SCR ELEKTRONIKS
Our core competence is designing & manufacturing Customised Electrical Test Equipment & Compliance Verification Benches for electrical products.
- +91 9769251762
- contact@screlektroniks.com
- W-188(B),Phase - II MIDC
Dombivli ( E )
Maharashtra, Thane 421 204
India
-
product
High Voltage Inclined Plane And Erosion Tester
SCR ELEKTRONIKS have developed HIGH VOLTAGE INCLINED PLANE AND EROSION TESTER to carryout test specified in many standard to cover test method for the evaluation of the relative tracking and erosion resistance of insulating solid using liquid contaminant (ASTM D2303). Perform the Initial Tracking Voltage Test, Time to track Test, And Erosion Test as per selection.
-
product
High Voltage Tester
The High voltage tester for routine testing of MCBs combines a conventional high voltage tester with a specially designed robust fixture to hold 20 single pole MCBs at a time. The solution comes as a single trolley with easy-to-set test parameters with safety interlocks designed for user safety with respect to electric shock and mechanical fixturing. An advantage of the system is – it gives a high yield (20 MCBs are tested in about one minute) thus yielding user safety at a high value for money.
-
product
High Voltage Tester For Hair Dryer & Hair Straightner
Every electrical apparatus or machine consists of two distinct sections - one which carries the electricity, and other which is isolated (insulated) from the electric currents. The former may be called the `Live' side whiles the latter `Earth’ side. A person near about the apparatus or handling it can safely touch the Earth side, but not the live side, for obvious reasons. To ensure that the isolation of the two sections is effected properly, the apparatus is tested by subjecting it to a Voltage much higher than the normal working Voltage. If the insulation is good, it stands the test without breakdown otherwise high electrical stress punctures the insulation at its weakest spot foretelling a later calamity to unwary user. Government Department- when buying electrical equipments- and all reputable manufacturers test every piece of equipment by this test called HIGH VOLTAGE TEST. It weeds out poorly insulate apparatus.
-
product
Hot Wire Ignition Tester
The HWI test indicates a materials resistance to ignition when exposed to abnormally high temperatures resulting from a component failure such as a conductor carrying far more than its rated current. HWI performance is expressed as the mean number of seconds required to ignite a specimen when wrapped with an energized non-chrome resistive wire that dissipates a specified level of energy.
-
product
Impact Test Apparatus
SCR Elektroniks make Impact Test Apparatus is used to test the Electrical Accessories / appliances for their mechanical strength.
-
product
Needle Flame Test Apparatus
Needle Flame Test Apparatus is designed to carry out fire hazard testing. Flammability test is to check the ‘Resistance to Fire’ of electrical insulators that touch directly conducting parts & also parts of insulators. Testing with regard to fire hazards can be done by creating exactly the conditions occurring in practice. However, this is not possible in most instances. Hence for this test, the actual conditions are simulated as closely as possible by the Needle Flame Test Apparatus.
-
product
PC Based Comprehensive Test Setup for Luminaires
Our zest for innovation has resulted in continuous upgrades in the existing line of products. Till now we used to manufacture 3 different equipments for Driver, MCPCB and Luminaires Component testing. We at SCR Elektroniks have developed our comprehensive tester to incorporate all the 3 systems in a single bench. Here in this tester one can test all the three DUT in a single bench. Since all the 3 testing procedures have many tests in common, we have incorporated all the tests in a single bench such that testing of Luminaire driver, Luminaire PCB and Final Luminaire set is performed in single test bench. Only these tests are performed over the DUT else other are disabled for them.
-
product
PC Based High Current Test Set for Circuit Breakers and Temperature Rise Test Equipment
This equipment comprises of high current source for testing of circuit breakers with additional facility for temperature rise testing (thus incorporating testing for moulded case, vacuum & air circuit breakers as per IEC 60947-2). The system integrates a servo controlled source with closed loop current feedback to maintain the current constant. It has the necessary instrumentation for maintaining current at full load & other conditions arising in testing at high current. The bench has a PC based control system with temperature data logger (24 channel with ch-ch isolation amplifiers). The data logger displays as well as stores a set of temperature values with time.
-
product
PC Based Test Setup for Electric Iron Testing
SCR ELEKTRONIKS make PC Based Test Setup for Electric Iron Testing is useful to carry out various tests mentioned in IS 366:1991 clauses 10,11,12,13 & 14 on the Iron under test.
-
product
PC Based Test Setup for LED Driver of LED
The tests are Performed as Prescribed in IS the Panel Carries out high voltage, open circuit and performance tests, one by one and provides indication of the Test results as PASS or FAIL lamp for high voltage test. It is very useful and handy in line testing on Mass production line as well as type Testing. Special fixture can be provided for the specific product. This avoids the connections & disconnections of the product for different tests. The total time for entire testing is less than 80 seconds. Micro controller based sequential timer maintains the sequence of operation and displays the test status. The entire system is housed in sturdy M.S cabinet with powder coating.
-
product
PC Based Test Setup for LED PCB of Luminaire
The panel carries out different tests one by one and provides indication of the Test results as OK or NOT-OK. It is very useful and handy in line testing on Mass production line as well as type Testing. Special fixture can be provided for the specific product. This avoids the connections & disconnections of the product for different tests. The total time for entire testing is less than 40 seconds.
-
product
Abrasion Test Setup for Coating of Hair Straightener
SCR ELEKTRONIKS have developed "4 Stations Abrasion Test Setup for Coating of Hair Straightener" for Testing of Hair Straightener. It consists of Adjustable Constant Voltage source, Digital Timer, Digital Voltmeter, Digital Timer for carrying out Heating Test of Hair Straightener. It has got the capacity to check hair straightener that require test current 28 A at different Test Voltages.
-
product
Arc Ingintion Tester
The product is designed to carry out Arc Ignition Test as per IS/IEC 60947-1 Clause 8.2.1.1.2 (material used for electrical products). The adjustable current source is 230V AC @ 33A. The load is adjusted to get 32.5A at 0.5 power factor. Included on control unit are Digital Voltmeter, Digital Ammeter, Digital Power Factor Meter and Micro Controller based programmable Sequence Timer with LCD display for display & setting. The arrangement is made to mount the test piece with electrodes as per the specification given in the standard.
-
product
Ball Pressure Test Apparatus
The Ball Pressure Apparatus is designed to perform test specified in IS Standard where resistance of insulating material to elevated operating temperature is to be determined. It is used to test insulation materials used in Electrical Appliances, Electrical wiring accessories, luminaries, motors, connectors, etc. It is a precision engineered test instrument for use by safety and compliance testing laboratories.
-
product
Commutator Testing Unit
SCR ELEKTRONIKS have designed “Commutator Testing Setup” to provide Commutator manufacturers and users a simple and speedy method for testing their Commutators. This single station commutator testing set up therefore user can test one commutator at a time. In Automatic mode of testing this set up performs two tests automatically.
