James Instruments Inc.
James Instruments Inc. is the leading manufacturer of non-destructive test equipment for concrete and other coarse grained materials. We supply the instruments that measure and analyze strength, structure, corrosion and moisture in concrete.
- 1-800-426-6500
773-463-6565 - 773-463-0009
- info@ndtjames.com
- 3727 N. Kedzie Avenue
Chicago, IL 60618
United States of America
-
product
Air and Water Permeability in Concrete Both At and Below the Surface
Poroscope
Poroscope Plus measures the time it takes for air to flow into a known volume of a sealed, evacuated chamber in the concrete. While the vacuum reduces from -55 Kpa to -50 Kpa, a measure of air permeability is determined. For water permeability, Poroscope Plus uses the same chamber filled with water, and measures the total time in seconds for a volume of 0.01 ml of water to escape.
-
product
Moisture Master
T-M-170
The James Instruments Moisture Master utilizes the latest electronic technology to measure the quantity of water within its sensing field. The unit has two modes of operation the pin mode, and search mode. In the pin mode, two pins are pushed into the material and a high frequency field is created between these two pins.
-
product
Trident
T-T-90
The Trident T-T-90 utilizes the latest microwave and microprocessor technology to measure moisture content in various fine and coarse-grained materials. The prongs of the probe are inserted into the material to be tested and the percentage of moisture content is instantaneously shown on the easy to read display.
-
product
Impact Echo SystemFor Field Evaluation of Concrete Structures
Vu-Con System
The Vu-Con Analyzer provides the engineer with the sturdiest, most reliable system for impact echo analysis. No moving parts and implementation of the latest microcomputer technology has created a system that is both sophisticated and reliable. The unit comes with a 90 mm (3.5?) by 115 mm (4.5?) graphic display screen that is easily viewed in daylight
-
product
Concrete Hardness Tester
W-C-7312
It is recommended that calibration of the test hammers be checked regularly usually after about 2000 strokes.The James Calibration Anvil (W-C-7312) has been designed for just that purpose.
-
product
Moisture Testing
Determine moisture in concrete and other construction materials. Meter for rapid determination of moisture content in sand and other fine or coarse aggregates. moisture content in Solid Materials. Includes Meter, Test Cable and Case. Meter for the Rapid Determination of Moisture Content in Different Types of Soil. Determination of Water/Cement Content Ratio in Fresh Concrete. (Type R for Regular Water Cement Ranges. Type L for Low Water Cement Ranges.)
-
product
Aquameter
T-M-160
he James Instruments? Aquameter MK II utilizes the latest electronic technology to measure the quantity of water within its sensing field. The T-M-160 using a high frequency capacitive sensor, samples a large volume of material, approximately 460 mm x 670 mm x 25 mm (1 13/16? x 2 5/8? x 1?), instantaneously.
-
-
product
Resonant Frequency Testing
E-Meter MK II™
Determines resonant frequencies of the three modes of vibration. Material characteristics such as Youngs Modulus of Elasticity, Modulus of Rigidity, Poissons Ratio and Damping Constant can be calculated. Frequencies are automatically scanned in one of four ranges. The system can determine flexural resonance of concrete under accelerated freezing and thawing cycles and aggressive environments.
-
product
Digital Test Hammers
James Instruments? digital test hammers are an advanced, completely automated system for estimating concrete compressive strength. Its calculation, memory and recording functions allow for quick, easy and accurate test results.
-
product
Ultra-sonic Test System
V-Meter
The V-Meter is an advanced ultrasonic, pulse-velocity test system widely used for quality control and evaluation of concrete structures. It can identify non-homogeneous conditions such as voids, cracks, honeycombs and frozen concrete.
-
product
Concrete Measuring and Monitoring System
IQM-Meter
Designed specifically for monitoring and analyzing fresh concrete, the IQM Module is programmed with the required Equivalent Age of the concrete under test. Once this preset maturity number is reached, a visual indicator will flash continuously, providing an effective, automatic indication that the concrete has reached the desired level of maturity.
-
product
Hand Held Microwave Moisture MeterFor Water/Cement Ratios of Fresh Concrete
Cementometer
The James Cementometer represents a break-through in modern moisture measurement technology. By utilizing the latest microwave and microprocessor science, the Cementometer can determine the moisture content of freshly mixed cement, concrete, and mortar. Simply insert the prongs of the probe into the material to be measured and instantaneously the water cement ratio is shown on the easy to read display.
-
product
Concrete Hardness Tester
W-M-350
The W-M-350 Recording Test Hammer gives you the same quality as the W-M-250 but with the added feature of a built-in automatic chart recorder. Every test you take is automatically recorded as a bar chart on a paper strip.This creates a field record to verify your findings.In addi- tion to this paper record,you can see each test as it happens through the large easy to read window
-
product
Ultrapulse
The James Ultrapulse is ideally suited for the testing of ceramic materials, refractories, plastics and laminates. Ultrasonic velocity measurement permits accurate and repeatable calculation of modulus of electricity, bulk density and the detection of cracks. Stored data can be uploaded to a PC with the optional hand-held terminal. The Ultrapulse can be used with a wide range of ultrasonic stansducers for all of your ceramic testing needs.
