6TL Engineering
6TL is a pioneer in applying the modularity concept to the design of Automated Test Equipment for electronics products. FastATE® Technology is the core to developing turn-key solutions that are truly modular, scalable and flexible, and thus we help to make the job of both test engineers and budget managers much easier. Thanks to FastATE, test engineers do not have to address the recurrent tasks of every project: a 6TL module completes these tasks for them. Each module selected is a high-level block that covers a function of the ATE and works together with the rest making in the end a real modular and flexible production test solution. The resulting test solution will be easily documented and will smoothly become the standard for the production, since the standardization is in the genetics of the FastATE® Technology.
- 34 937 270 074
- info@6tlengineering.com
- PASSATGE DE LA NOGUERA, 2
CASTELLAR DE LAS VALLES, BARCELONA 08211
Spain
-
product
POF Ext Ø 1,5mm 600mm, from Light Probe to VPC ITA Contact (R)
YAV90CLR11
600mm Length 1,5mm External diameter
-
product
10-CH Pneumatics CAN
YAV90PNE
The YAV90PNE is a complete “plug & play” pneumatics subsystem controlled by CAN, for ATEs with Virginia Panel receiver. Thanks to this module, pneumatics actuators that are commonly used in the fixture side of an ATE, can be controlled. 10 3-way micro-valves are able to contorl 10 simple effect actuators or else 5 double effect ones. The module includes input for the position sensors. A pressure sensor is also included, so that the system air mains working pressure can be set between a minimum and a maximum.
-
product
64-Ch SPDT 2A-240VAC 24VDC Switching
YAV90164
64 relays SPDT, 2A Switching 2A 250Vac. Up to 62,5VA CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
product
8-Ports Gigabit Ethernet RCV Interface (R)
YAV90058
8x RJ45 LAN connectors to VPC RCV 192 pins module.
-
product
10-Ch. 0… 5V 400mA Isolated
YAVAP955
The YAV board AP955 contents 10 CAN Bus programmable bipolar Isolated precision and low noise 0 to 5VDC voltage sources up to 400mA output, with Tripaddle VPC connector.
-
-
product
32-Ch High Voltage Relays & Multimeter
YAV90HVT
The YAV90HVT is used as an automatic CAN bus controlled floating AC/DC true RMS digital volts/milliamps meter with built-in scanner, able to work directly in appliances and industrial mains powered electric/electronic equipment.Its powerful microcontroller allows to work as a distributed device able to data acquire, compare and return high level messages, reducing test operation time.The analog output is used as a set value for the optional high voltage programmable power supply for Hipot tests up to 1500V.The board uses Tripaddle connection modules and can operate as stand alone or be mounted on a standard Virginia Panel receiver.The board includes National Instruments LabView virtual control panel and operating software for a true Plug & Play operation.
-
product
4x IDC to 192 Pin Quadrapaddle
YAV90Q04
The interface YAV90Q04 permits to connect two YAV90096 boards to one 192-Signal contacts Quadrapaddle module. As the Mini-D 50 connectors let 2 free pins (1 and 26), these pins are interconnected to a test point, with the possibility of be grounded. Cable P/N J6200540: Mini-D-50 to Mini-D-50 IDC connectors with 400 mm flat cable.
-
product
ATE Self Test Fixtures
AL663
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
product
21-Ch 6A-250VA 2-Bus Fault Insertion
YAV90077
21 channels 1 thread 6A 250V 2 Fault Insertion Buses Switching up to 250W CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
12-Ch 10A RCV Power Distribution Unit
AR438
AR438 module helps with interconnection, power supply and load switching, monophasic and triphasic, adding the current measurement capability up to 10A.Enable input helps for a safe relay disconnection. It is a quick electrical -hardware- disconnection of the relays and is designed to be an auxiliary safety element, so that loads cannot reach the device under test.
-
product
USB 3.0 And RJ45 Cat6 To VTAC Interface
YAVAM852
USB and RJ45 sockets to VTAC VPC contactsHigh speed interface between connectors up to 1GbpsAvoids noise and interferences on signals thanks to VTAC contacts technology
-
product
Electronics Manufacturing Services
In many cases variability of production and test platforms available restricts production flexibility and may cause bottlenecks in factories. Therefore, standardization of existing test equipment and reusability of fixtures/needle beds in off-line and in-line platforms are essential aspects.
-
product
48 Optocoupled Open Drain 42V 6A Digital Outputs
YAV90048
6×8 Isolated Ouput Banks Trigger IN and OUT Termic and Overcurrent protection CAN Control (or Ethernet with Ethernet to CAN Gateway.) Drivers dll & VIs available.
Related
-
Virginia Panel Corporation
Virginia Panel Corporation (VPC) provides VPC provides Interconnect Solutions that enable simultaneous connection of multiple test and measurement signal types through one modular interface. Designed to accommodate signal, power, RF, thermocouple, pneumatic/vacuum, and fiber optic connector modules in multiple configurations, VPC’s innovative products meet the demands of test & measurement interconnect requirements.
-
Columbia Elektronik AB
COLUMBIA ELEKTRONIK AB is an expert organisation delivering complete test fixturing solutions to the Nordic electronics industry. Having pioneered the Swedish, Norwegian, Finnish and Danish markets back in 1977 we have today an absolute leadership in fixturing and test technology and enjoy a solid, major share of the market. We cover the whole spectra with testsystems, testfixtures, mass interconnect solutions and both hardware and software support and services. We design and produce both our own and vendor delivered testfixtures and mass interconnect solutions for functional and in-circuit test of electronic products and assemblies from component and PCB level to subassemblies and finished products. Columbia excels in all modern fixturing technologies – be it vacuum actuated, mechanical or pneumatic – applied to stand-alone, tester-integrated or inline fixtures.
-
DFT - MG-Products BV
DFT, Designed for Testing. is part of MG-Products and is specialized in the delivery of functional Testfixture solutions from both MG-products and 6TL. DFT also stands for Design For Test, perhaps the most important step in the development process of your product. DFT ensures that your product can be contacted and tested efficiently and reliably.
