SLSC Cards
SET GmbH (Steiner Elektronik Technologie)
SET offers a variety of different signal conditioning cards for connecting DUTs. The platform is designed to allow additional cards to be developed effectively in terms of cost and time.
-
product
Routing Card
SET-2010
With 64 single-ended or 32 differential channels, the SET-2010 provides exceptional signal routing capabilities in a small form factor. Unlike traditional routing matrix cards, the SET-2010 is designed specifically for the challenges of signal routing in HIL systems.
-
product
Real Time Fault Module
SET-2315
The main function of the module is to multiplex signals on the fault buses.With 16 channels, the SET-2315 provides real time fault connection capabilities in a small form factor.The fault bus leads to the base cards connector to connect any fault device.
-
product
Fault Insertion Unit Card
SET-2110
Each line of the 32 single-ended or 16 differential channels can be connected individually and flexibly to the high current fault injection bus. For this, one of the both fault bus signal pairs can be selected dynamically for every channel. The SET-2110 Fault Insertion Card also provides the ability to generate short circuits between a channels positive and negative signal.
-
product
32Ch Isolated Output Card
SET-1320
This card offers 32 optically separated open collector outputs that can switch up to 100mA at 60V. SET-1320 combines tight IO with high isolation voltages and an extensive output voltage range.
-
product
32Ch Isolated Input Card
SET-1310
This card provides 32 optically isolated digital inputs. SET-1310 combines high-density IO with high isolation voltages and a wide input voltage range. It allows to break ground loops and protect your system from high-voltage spikes, but also to connect high voltage signals to standard logic level acquisition devices. The channel-to-channel isolation allows to connect signals from different DUTs to a single acquisition system without compromises.
-
product
Resistor Simulation Card
SET-1210
The card has two ranges of values that meet the requirements of most functional test systems.The SET card is designed for applications in which resistive sensors provide information about parameters such as temperature (e.g. when testing motor controls)Each channel of the SET-1210 resistor simulation card is able to simulate the common short-circuit and no-load conditions, which can occur in a system due to faulty wiring or sensors.
-
product
RTD-SIM Card
SET-1215
The simulation range is from 90 Ohm to 410 Ohm and 900 Ohm to 4100 Ohm with an accuracy up to 1°C.It contains 16 galvanic isolated channels which can be connected in 2-terminal sensing and 4-terminal sensing.Each channel of the SET-1215 card is able to simulate the common short circuit and open circuit conditions, which could be experienced in a system due to faulty wiring or sensors.
-
product
Capacitance Simulation Card
SET-1220
The SET-1220 device is a designed capacitive fuel sensor emulation for NI-SLSC. This card provides eight isolated channels that can emulate capacitance values between 10pF and 800pF. It was designed to emulate capacitive sensors that are typically connected between an excitation voltage on one end and a virtual ground on the other end.
-
product
xVDT emulator card
SET-1240
In addition, the card offers 8 independent, galvanically separated channels. In addition to a wide excitation frequency range from 400Hz to 10kHz, the card also offers various self-test options. The transformers are located on an exchangeable sub-card and can thus be easily exchanged or specified by request from us.
-
product
32CH 4-20mA Current Sink Card
SET-1250
Each channel provides an isolating relay and a short-circuit MOSFET with which opening and short-circuit errors can be simulated. The short-circuit MOSFET has overcurrent protection with integrated current limitation.
-
product
32 Channel Pass Through Card
SET-2090
The input signals can be configured by customers. Each input channel can be tested, conditioned or measured in different ways. Various inductors, filters, pull-up or pull-down resistors can be used for this purpose. In standard configuration, the input signals are transmitted directly to the output.
-
product
ARINC 429 Card
SET-1623
The SET 1623 ARINC Card has 32 Tx/Rx Channels. These 32 Tx/Rx channels are structured in 4 banks (P0.x to P3.x) 8 channels each. Each bank is controlled by a dedicated SPI (SPI0 to SPI3) located on RTI.
-
product
PSI5 Sensor Interface Card
SET-1640
PSI5 is an open standard based on existing sensor interfaces for peripheral airbag sensors and has already proven itself in millions of airbag systems.
