Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI 5A Mux 1-Bank 48-Ch Isolated COM + Ind Isolation
40-651-111
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel. Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
product
DC Power Supply
Instrumentation is needed for a wide variety of experiments. This category includes both power supplies and measuring devices.
-
-
product
Micsig AC & DC Current Probes
CP2100
Shenzhen Micsig Instruments Co., Ltd.
*Split design, small and exquisite appearance, easy to test *Compatible with all BNC-connected oscilloscopes, adapters can also work with multimeters.
-
product
110 GHz Frequency Extender, Pulsed DC Bias
N5293AX52
The Keysight N5293AX52 is a broadband frequency extension module designed for use with Keysight’s new PNA / PNA-X-based millimeter-wave solutions. It is a compact, lightweight, and ruggedize frequency extender module with built-in bias tee for pulsed DC bias operation. It interfaces with the Keysight N5292A test set controller. The modules allow users to extend the frequency coverage of a base PNA / PNA-X Series network analyzers to a range of 10 MHz to 110 GHz. For more information about cable and accessories for use with network analyzers, please visit Network Analyzer Accessories.
-
product
HIGH FREQUENCY DC BIAS
6565 SERIES
The 6565 HF DC Bias Unit is intended to be used with a Wayne Kerr 6500 analyzer, either the 6500B Precision Impedance Analyzer or the 6500P HF LCR Meter. Its function is to provide a source of DC bias current through the Device Under Test (DUT) while the analyzer is making AC measurements. Each 6565 unit can provide up to 10 A of DC current, and up to six 6565 units can be connected in parallel to supply a maximum 60 A. A digital ammeter on the front panel allows the user to see the dc bias current value and an indicator LED shows when the bias current is enabled.
-
product
PXI Hybrid Coaxial Switch: DC to 40 GHz, Dual Transfer
M9156CH40
The Keysight M9156CH40 PXI hybrid dual transfer switch module provides an exceptional 0.03 dB insertion loss repeatability, high isolation, low SWR with a long operating life up to 10 million cycles.
-
product
STP-25 Replaceable Step Probe
STP-25
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 135Full Travel (mm): 3.43Full Travel Remark: Varies with tip (min. 135 mil / 3,43 mm)Recommended Travel (mil): 120Recommended Travel (mm): 3.05Overall Length (mil): 1300Overall Length (mm): 33.02
-
product
High Current / High Voltage Pulsers
DEI Division
Berkeley Nucleonics Corporation
is optimized for high impedance capacitive loads, driving extraction grids and deflection plates, and pulsing or gating power tube grids. It generates an output voltage of 6,000 volts with rise and fall times less than 60ns, with very flat voltage pulses from 160 nanoseconds to DC into a capacitive load.
-
product
Resistors for Calibration of Current Measuring Systems and Sensors/Transducers
ChenYang Technologies GmbH & Co. KG
Is designed and made according to the Standard JB/T8225-1999 for DC resistors used in laboratory and electrical engineering.By using full closed structure and automatictemperature control it ensures resistor good long-term stability and small temperaturecoefficient. This DC resistor is very suitablefor DC current measurement and calibration of current measuring systems and current sensors. The maximal measuring current is 100A with measuring accuracy of ±0.02%
-
product
Line Injector
J2120A
While the injection transformer is a very wideband adapter, it is not useful for measuring ripple rejection (PSRR) of a power supply or even an opamp. This is because the attributes that make the injection transformer perform so well also result in a transformer that is intolerant of DC current. Even very small DC currents (5mA or less) can greatly reduce the signal capacity or even totally saturate the transformer. For this reason, the Picotest line injector (J2120A) is another essential test adapter.
-
product
Tx/Rx SignalBlade
This ATCA compatible test card offers the flexibility to verify the performance of Advanced TCA fabric and base channels. The set of four Transmit pairs and four Receive pairs allows access to a full channel's eight pairs for backplane path characterization. The card includes a HM-ZD connector segment for access to the backplane and edge-launch SMA connectors for ease of test cable attachment. DC blocking capacitors are included on the receive pairs as required by Advanced TCA.
-
product
Static Elimination
Fraser Anti-Static Techniques Ltd
Cost-effective passive, AC or 24 V DC technology solutions for static neutralisation, dust removal and cleaning.
-
product
Solenoid Valve Tester
DZ800
Shanghai Aoboor Electric Co., Ltd.
Insulation resistance, HIPOT, coil DC resistance, turn to turn surge tests can be automatically completed in one time. Applicable to electrical performance test of solenoid valves, changeover valves
-
product
Slip Ring Test System
This is a high specification tester that will measure many cable parameters. It measures cable resistance very accurately using the Kelvin 4-wire method. It also tests for shorts between pins at a low voltage. The next test is to measure insulation between connections at a higher voltage. This is carried out at up to 1500 Volts DC with resistances of 10 to 500 Meg ohms.
-
product
AC & DC Analog Leakage Meters
506 EL
Standard Electric Works Co., Ltd
● Optional for pivot or taut band movement.● Compact and lightweight; easy to use and store.● Mirror scale: for easier viewing & reading.● Built-in stand makes reading and measuring easy.● 200μA full scale value.● Fuse-protected.● Low battery indication.
-
product
Guardian Hipot Tester AC/DC/IR/SCAN
19050
Chroma Systems Solutions, Inc.
The Chroma Guardian 19050 series of Hipot Testers are comprised of three models. The Guardian 19052 is equipped for AC/DC/IR Hipot testing and insulation resistance (IR) measurements. The Guardian 19053 combines both AC and DC Hipot tests and IR measurements with 8HV scan channel capabilities. The Guardian 19054 combines both AC and DC Hipot tests and IR measurements with 4HV scan channel capabilities.
-
product
HandyScope HS6-DIFF With SafeGround & SureConnect: 1 GS/s, 250MHz BW, 4 Channel (256MS/ch), USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS6-DIFF-1000XMSG-W5
- 1GS/s sampling and flexible resolution of 8-16 bit.- Four input channels up to 250 MHz analog bandwidth- Highly accurate 1 ppm time base- DC Accuracy of 0.25 % and 0.1 % typical- Very fast 200 MSamples per second USB streaming Data logger- Spectrum analyzer with 32 million bins- Optional SureConnect connection test on all channels- Up to 256 MSamples memory per channel
-
product
4-in-1 OSLT Calibration Kit, DC to 70 GHz, Type-1.85 mm (m)
CK058M
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
product
SCR CONTROLLED DC POWER SUPPLY
PS Series
Variable DC power supplies are AC to DC power supplies with a variable DC output. The output can be varied with an SCR controller. The AC input power can be single phase or three phases. With single phase AC input, the DC output ripple is very high (50%). With three phase AC input, the DC output ripple is low (5%). This would be a key benefit for selecting three phase AC input instead of single phase.
-
product
DC Electronic Load
EE30140A
The EE30140A DC Electronic Load / Works @ 0.0 Volts Input & real time I/O control. attach the electronic load block to a heat- sink and your up and running used them with D to A's, A to D's, Pots, PLC's to control the current. These Electronic Loads can be used for both Discharge & Charging Batteries & Devices
-
product
Energy Saving Static Converter
The ENERGY SAVING static converter serves to generate a controlled squarewave single-phase alternate voltage (low frequency: 25 ÷ 125Hz) for industrial applications requiring high load power supplied by an external matching transformer. The power supply, sectioned by remote control switch and external fuses, is fed by a three-phase electric line via uncontrolled diode bridge and filtered by inductor and capacitor battery. The DC voltage thus obtained is converted into single-phase alternating voltage via “H”-shape bridge of semiconductors in order to control impressed frequency single-phase transformers.
-
product
DC Resistance and Current Measurement System
DC Resistance and Current Measurement System including: 6622A Series Bridge, 6634A Temperature Stabilized Resistance Standards, 6664C Scanner(s), world’s most precise and stable 6623A Precision Current Source/Range Extender, Wired Equipment Rack, and Bridgeworks Software.
-
product
Power Divider, DC to 18 GHz
11636A
The Keysight 11636A is a dc to 18 GHz power divider for direct power dividing applications. The excellent impedance match of all three ports improves fault location measurements by reducing re-reflections. The Keysight 11636A power divider/combiner is recommended when making wideband comparison measurements with a Keysight 8757 scalar vector network analyzer.
-
product
PXI Chassis
PXI Chassis are compatible with PXI, PXI Express, and PXI hybrid modules and meet the cooling requirements of the most power-demanding PXI modules. You can also choose chassis options that minimize the overall system acoustic emissions. Chassis can provide up to 18 slots, with a mixture of both PXI and PXI Express module compatibility, and you can choose between AC and DC power options.
-
product
Bench Power Supply, Switching DC, Adjustable, 1 Output, 0 V, 12 V, 0 A, 30 A
T3PS11230
Bench Power Supply, Switching DC, Adjustable, 1 Output, 0 V, 12 V, 0 A, 30 A.
-
product
WiFiScope WS6: 200 MS/s 250MHz BW, 4 Channel, Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
WS6-200XM-W5
*Oscilloscope / Spectrum analyzer / Voltmeter*14 bit (0.006 %) resolution (16 bit enhanced resolution)*200 MS/s sampling*250 MHz bandwidth*Up to 64 MSamples memory per channel*0.25 % DC vertical accuracy*1 ppm timebase accuracy*WiFiScope advantages
-
product
DC Blocking L-Band Splitter Combiner
PD5960
INSTOCK Wireless Components, Inc
PD5960 is an IP67 outdoor, weather resistant, DC blocking, six way, RF broadband, 50 ohm, power divider, power combiner furnished with TNC coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5960 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 6 way power divider input rating tables for additional power handling info.
-
product
Sound Level Meter, 94 dB, 114 dB, 0 °C, 50 °C
72-2680
The 72-2680 from Tenma is a sound level calibrator. It is a useful tool to calibrate the sound level meter. It has two heavy duty or alkaline type, DC 9V batteries 006P, MN1604 (PP3).
-
product
Low Noise Differential Preamplifiers
Provide a high gain amplification to 1MHz with an AC output derived from a very low noise FET instrumentation amplifier. Each model has fixed gain settings of x1 (0dB), x10 (20dB), x100 (40dB) and x1000 (60dB) over a selectable bandwidths of 100Hz, 1kHz (HP), 3kHz, 30kHz, 100kHz and 1MHz (7000 model only). Noise referred to input is 7nV√Hz and common mode rejection is >100dB at 1kHz. Momentary pushbutton switches are provided that control coupling, bandwidth, gain and channel on/off selections. BNC connectors are provided for single-ended and differential input, ac output, and dc output (optional) connections.
-
product
High Voltage 50 Ω Pulse Generator
TLP-4010C
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Ultra fast 50 Ω high voltage pulse output with typical 100 ps rise time*Built-in HMM (IEC 61000-4-2) pulse up to ±10 kV*High pulse output current up to ±40 A*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns*Optional pulse width extender increases pulse width up to 1.6 µs in 68 programmable steps*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurement of complete wafers*High performance and high quality components
