Filter Results By:
Products
Applications
Manufacturers
Substation
transform and distribute electrical power.
See Also: Power Distribution, Switchgear, High Voltage Transformers
- CTRL Systems, Inc.
product
Electrical Inspector
The UL101 Electrical Inspector utilizes airborne attachments to safely inspect sealed electrical panels and substations. The UL101 Electrical Inspector allows for early, long-distance detection of arcing, corona discharge, and tracking. Save time and money by reducing transmission/distribution loss and outages.
-
product
Measuring And Testing Equipments For Substations
Measuring and testing equipments for substations
-
product
Substation Equipment Test Van
ETL-250
Apart from insulation withstand testing with DC (rectified) voltage up to 60 kV and ability to measure very small leakage currents, the system can be used for testing various objects with small electrical capacitance with AC voltage of up to 250 kV and measuring dielectric dissipation factor (Tan Delta) at industrial frequency.
-
product
HardFiber System
IEC 61850
The HardFiber System is a KEMA tested IEC 61850 Process Bus Solution that allows the mapping of measurements made in the switchyard to protection relays located in the control house using secure communications. The HardFiber System addresses the key technical and logistic challenges affecting the labor required for substation design, construction and maintenance.
-
product
DC High Voltage Break Down Tester
High Voltage Breakdown Testers also known as Hipot Testers or Insulation Testers are a necessity for any Transformer testing, Substation equipment testing, Cable testing, Panel testing and testing of various insulating materials. Insulation testing is very important to ensure and maintain the safety of electrical equipments and also for the safety of operator.
-
product
Protection Relays
ROCON designs and manufactures large variety of world-class intelligent electronic devices (IEDs) for relay protection and automation. They are applicable for all kind of utilities in industry - for all power system facilities (in production, distribution and transmission of energy to the end user) for transport companies, for factory substations etc.
-
product
IRIG B Booster
Signals & Systems India Private Limited
IRIG B Booster – SIB-1010 is used to boost the IRIG-B AM and PWM/TTL signal which is received from the GPS unit. It provides easy and affordable connectivity to substation equipment and power generation and distribution equipment. With this Plug-N-Play unit, you can expand your IRIG B connections to multiple devices instantly. It is rugged and surge-protected equipment. Its cabinet can be mounted directly on a wall, panel or DIN Rail, without the need for additional brackets. It has an inbuilt power supply module, therefore, doing away the need for an external power adapter.
-
product
Three Phase Power Meter
929A
Model 929A Three Phase Power Meter is an economical alternative to both the Model 931A Power System Analyzer and the Model 930A Three Phase Power Analyzer when serial communication, dc voltage measurement, transducer calibration and timer features are not required. The Model 929A has the same ac accuracy as the Model 931A with PowerDSA™ Digital Signal Analysis, and is a complete diagnostic tool for use in the substation and industrial power environment.
-
product
Remote Terminal Unit (RTU) Replacement
Schweitzer Engineering Laboratories, Inc.
Compared with typical RTUs, SEL automation controllers provide improved reliability, extended I/O contacts, and advanced automation and control for remote substations and field applications.
-
product
Annunciators
RAU-D is designed to be used for alarm and warning signalization in Conventional and Digital substation automation projects.
-
product
Automation Control
Schweitzer Engineering Laboratories, Inc.
Monitoring and controlling substation power systems requires comprehensive solutions. SEL’s complete solutions and hardened devices help maintain system stability with deterministic control; streamline access to valuable IED data, communications processors, and field devices; and improve visualization and control with local HMIs and access to SCADA systems.
-
product
Digital Power and Energy Measurement
EPM 2200
The EPM 2200 meter measures more than 40 electrical power parameters providing a low-cost, multifunction monitoring solution for industrial and power generation applications. EPM 2200 can easily be mounted in a panel for generator monitoring, substation automation and more. The meter can also provide data to RTUs, PLCs and other control devices.
-
product
Hybrid Signal Analyzer
DANEO 400
DANEO 400 is a hybrid measurement system that records and analyzes all conventional signals (voltages, currents, hard wired binary status signals) and messages on the communication network in a substation.
-
product
Electrical Power Transducers
Manufactured for utilities since 1969, TransData Power Transducers are used for measuring AC and DC power variables in Substation, Generation, Load Control and Industrial applications where ±1ma or 4-20mA analog signal are required by the SCADA/Energy Management System. Models are available for measuring Current, AC Voltage, DC Battery Voltage, Watts, VARs, Frequency and more.
-
product
Primary Test Equipment
LET-2000-RD
It allows to perform with sufficient power, all the primary current injections to test the proper function and wiring of all the elements that compose the protection and measuring section in a substation.
-
product
Compact Unmanaged Ethernet Switch
ML600
The MultiLink ML600 is a Compact Unmanaged Ethernet Switch that is ideal for Industrial Facilities, Substations, and Transportation environments that have few Ethernet devices in one location. As a very cost effective solution, the ML600 will supply you with high speed networking in your harsh environments and is equipped with Link Loss Learn (LLL) that allows for use in redundant architectures thus ensuring you will always have access to your devices.
-
product
Surge Arrester Testing
Weshine Electric Manufacturing Co., Ltd
This instrument can be widely used in equipment maintenance of substations and power plants, and to measure insulation resistance, absorption ratio and polarization index of high-voltage electrical equipment such as transformers, reactors, capacitors, and circuit breakers. The leakage current of the low-voltage arrester of the power distribution cabinet is automatically tested.
-
product
Megohmmeter
GM-20kV / 782
Wuhan Huatian Electric Power Automation Co., Ltd.
It is suitable for testing the characteristics of electrical insulation resistance in substations, power plants, remote power cables or buried cables.
-
product
UV Cameras
Solar blind UV cameras are imaging devices optimized to detect ultraviolet light of wavelengths below about 280nm. Such cameras are insensitive against sunlight due to negligible sensitivity to visible and long wavelength UV light. Solar blind UV cameras are used in a series of applications like corona detection, fire detection, combustion analysis, plasma research, testing UV lamps, etc. However, highly sensitive corona detection is the main mass application and these devices are of crucial importance in electric power industry. These imaging devices enable easy detection of degraded insulators of high voltage transmission lines, distributions and substations. They can see the emission of UV light when discharges occur at defect insulators. From design point of view solar blind UV cameras are actually bispectral imaging systems built by combining true UV camera with typical visible camera. These bispectral imaging system generate output image as overlay of typical visible image with UV image of analyzed UV source.
-
product
Earth Tester
TAURUS PRECIOHM ET
The TAURUS PRECIOHM ET is one of the specially designed products by TAURUS to measure earth resistivity and earth resistance in a power station. These tests are performed based on 4 point (Wenner) and 3 point (fall of potential) methods respectively. All electrical equipment in the substation and power stations are electrically connected to station earth mat with earth electrodes. The earth electrode ensures that in the event over voltage on the system due to system fault or lighting discharges etc., the parts of the equipment which are normally ”dead” as far as voltages are concerned; do not attain dangerously high potentials. An earth electrode will only be effective so long it has a low resistance to the earth and can carry large currents without deteriorating. Thus the resistance of earth electrode should be low to give good protection and it must be continuously measured and monitored in all the substations and power stations.
-
product
Routers
Schweitzer Engineering Laboratories, Inc.
Routers forward data packets to and from different networks. In utility networks, routers are often used to create security perimeters around substation LANs.
-
product
Polarity Checker
PW-VP50
PW-VP50 CT Polarity checker is the favorable meter which can be used for field CT and transformer polarity test in power plants, substations and any other application which may need to check the polarity. There are 2 units included in PW-VP50. One master machine which can automatically inject...
-
product
Bushing Monitoring
Qualitrol Bushing Monitor System is an on-line Tanδ (PF) and Capacitance monitoring system for substation bushings. It measures the phase difference induced by capacitive layers of bushings and calculates the rate of change to predict defects in bushing insulation.
-
product
Installation Support
Schweitzer Engineering Laboratories, Inc.
Completing a substation, panel, or a control house requires more than relays. SEL provides contact arc suppressors, linear power supplies, displays, selector switches, panel-mount hardware, bezels, dust covers, cables, and other accessories essential for a successful power system project.
-
product
Primary Test Equipment
LET-400-RDC
The LET-400-RDC is designed to perform most of the primary tests that are necessary in substations commissioning. It allows to perform with sufficient power, all the primary current injections to test the proper function and wiring of all the elements that compose the protection and measuring section in a substation.
-
product
Distributed I/O
Schweitzer Engineering Laboratories, Inc.
Expand the I/O of SEL relays and communications processors, reduce copper in substations by transferring I/O from remote locations over fiber, and provide electrical isolation to avoid ground paths and induced noise and interference.
-
product
Multifunction Substation Test Set
STS 5000
STS 5000 is a multifunction substation maintenance & commissioning test system for current, voltage and power transformers designed to perform primary tests requested in substations commissioning. It allows to perform accurate tests on CTs, VTs, PTs and ground grid.
-
product
Low-Voltage Arrester Analyzer
Weshine Electric Manufacturing Co., Ltd
1. This instrument can be widely used in equipment maintenance of substations and power plants, and to measure insulation resistance, absorption ratio and polarization index of high-voltage electrical equipment such as transformers, reactors, capacitors, and circuit breakers. The leakage current of the low-voltage arrester of the power distribution cabinet is automatically tested.
-
product
Current-transformer
Beijing GFUVE Electronics Co.,Ltd.
Are the current-sensing units of the power system and are used at generating stations, electrical substations, and in industrial and commercial electric power distribution.
-
product
Primary Injection Test Systems
Primary current injection testing is utilised in high current/high voltage scenarios found at large electrical installations such as substations. A large current (between 100A and 20,000A depending on system specifications and test requirements) is injected directly on the primary side of the electrical system such as a circuit breaker. The objective of the test is to identify how the system operates under various levels of current load.
-
product
Primary Injection Test Systems
Primary current injection testing is utilised in high current/high voltage scenarios found at large electrical installations such as substations. A large current (between 100A and 20,000A depending on system specifications and test requirements) is injected directly on the primary side of the electrical system such as a circuit breaker. The objective of the test is to identify how the system operates under various levels of current load.
