Filter Results By:
Products
Applications
Manufacturers
Fibre
cylindrical dielectric waveguide, which transmits light through total internal refraction.
See Also: Fiber, Fiber Optic
- Pickering Interfaces Inc.
product
PXI Single 2 x 2 Fibre Optic Mux LC
40-860-412
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
Fibre Channel Testing
The storage area network (SAN), created in response to enterprises' data storage needs, is a grouping of interconnected devices and servers that use a common communication infrastructure, combining and capitalizing on the best of both the storage and network worlds. The protocol used for this infrastructure is Fibre Channel.
-
product
Comb Generator
RefRad X
A comb generator is built inside a conical antenna element. Therefore no cable between antenna and generator is required. Thus leads to repeatable measurement results and reliable simulation of radiation performance.Optionally a fibre link for synchronisation with the receiver is used.Frequency Range 10 kHz - 3 GHzFrequency Spacing 10 kHz, 1 MHz, 5 MHz
-
product
PXI Dual 2 x 2 Fibre Optic Mux LC
40-860-422
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
"Signal Transporter"
LTX-5510
The LTX-5510 enables precise conveyance of analogue plus four channels of digital information over fibre optic links ranging from meters to more than 10 kilometers. Incoming analogue data is digitised to 12-bit precision at 50 mega-samples per second and transmitted over optical fibre at a 1 Gb/s data rate.?
-
product
Copper & Fiber Network Troubleshooter
NAVITEK NT
The new NaviTEK NT is a network tester for troubleshooting and maintenance of active and passive copper and fibre networks. Incorporating an improved graphical interface NaviTEK NT allows network technicians to pinpoint and solve network connectivity issues faster than ever before. Subsequently, tests can be saved as pdf reports and shared with colleagues and clients using the free IDEAL AnyWare™ app.
-
product
PXI Single 4 Channel Mux Fibre Optic MU
40-850-314
The 40-850-314 4-channel multiplexer is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
Digital Video Inspection Microscope
Contamination is the first reason for troubleshooting optical networks. Proactive inspection and cleaning of fibre connectors can prevent poor signal performance, damage to equipment, and network downtime. DIAMOND’s Video Microscope Kit contains all necessary tools for proper inspection and cleaning of the connector’s front-faces to help ensure optimal connector performance.
-
product
Barcol Impressor Hardness Tester
3101
The Elcometer 3101 Barcol Impressor Hardness Tester is easy to use and ideal for measuring the hardness of soft metals, plastics, glass fibre and leather.
-
product
1-Slot Thunderbolt 2 PCIe Expansion
EB1T
Power, Performance, Portability: Enhance the power of your laptop with the Magma ExpressBox 1T and harness lightning-fast throughput up to 20 Gbps over a single cable via Thunderbolt-2 technology. ExpressBox 1T enables serious professionals to use specialty PCIe cards with any Thunderbolt-equipped computer, so that you can achieve high performance wherever your work takes you. Add a PCIe card to ExpressBox 1T and your computer turns into a powerful workstation capable of HD video capture and editing, media transcoding, audio processing, data processing, or high-speed storage and networks. The ExpressBox 1T offers the largest card length slot (7.75”) among all 1-slot Thunderbolt chassis on the market, giving your Mac the power to achieve maximum performance with any compatible half-length PCIe card. Whether your mission involves professional video capture, audio interface, SAS & SATA HBA, 8Gb Fibre Channel, 10 Gigabit Ethernet, or a RAID controller card, Magma’s family of Thunderbolt products provide the perfect outsidethe-box solution for your project.
-
product
Additional Components
High-quality Splitter, Coupler and RF over Fibre Solutions. Made in Germany.
-
product
Optical signal transmission
Digital
The fibre optic cable are used to transmit digital signals from the device under test under EFT/burst interference.
-
product
Semiconductor Laser
·Fibre coupling semiconductor laser·The product range of wavelengths is 450nm~1550nm ·The product range of power is 2mW~300W ·A Variety of package coupling form,can be integrated indicator light,a photoelectric detector, a semmiconductor refrigerator,optical switch function·Solution of flexible and diverse,providing customized service sub system
-
-
product
PXI Single 2 x 2 Fibre Optic (M Mode)STM62.5
40-860-512-M62.5
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
O/E Converter
TIA-525
The TIA-525 optical receiver is a convenient, easy to use optical to electrical converter. It is extremely useful in a variety of laboratory and field service situations where a quick check of the operation of a laser source, optical transmitter, or the output of a fibre optic communications link is required.
-
product
O/E Converter
TIA-4000
The TIA-4000 is comprised of a fibre coupled InGaAs APD detector combined with a variable reverse bias voltage network and fast transimpedance amplifier. The output of the unit is brought out to a type K female SMA connector. Light falling on the detector generates a positive-going proportional current. This current, multiplied by the transimpedance produces a voltage that is proportional to the light incident on the detector surface.
-
product
SONET/SDH/OTN and Multiservice Analyzers
In the lab and network equipment manufacturing (NEM) environment, research and development engineers require scalable testing solutions with port density, multi-user accessibility and automation capability. EXFO’s IQS testing solutions provide R&D and carrier lab engineers with the right offering of multiservice test modules covering a wide range of technologies, including SONET/SDH, Ethernet, OTN, Fibre Channel, etc.
-
product
Electrical measurements
Instruments for measurement and analysis in accordance with the regulations of single / triphasic low voltage networks and data networks via cable or fibre.
-
product
Passive FTTx
Shenzhen Wiitek Technology Co.,Ltd
Fiber to the x (FTTX; also spelled "fibre") or fiber in the loop is a generic term for any broadband network architecture using optical fiber to provide all or part of the local loop used for last mile telecommunications. As fiber optic cables are able to carry much more data than copper cables, especially over long distances, copper telephone networks built in the 20th century are being replaced by fiber.
-
product
Signal Transporter E/O - O/E Converter pair
LTX-5515
The LTX-5515 enables the precise conveyance of one analog channel plus four digital channels of information over fibre optic links ranging from metres to more than 10 kilometres. Incoming analogue data is digitised to 12-bit precision at 100 megasamples per second and transmitted over optical fiber at one giga-bit per second.?
-
product
10 Gb/s SFP/SFP+ Evaluation Board
EV-SFP-171
The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceiver such as 10 Gb/s(up to 16 Gb/s) SFP/SFP+ transceiver compliant with ANSI Fibre Channel FC‐PI‐5 for high speed electrical and optical specifications. This board provides SMA connectors for high speed TX and RX signals. The low speed control signals such as Tx_Fault, Rx_LOS and Rate_Selects can be controlled by using on board switches and test points. A connector for 2 wire serial interface to the module is also provided.
-
product
PXI Express Instrument
PXIe-FC4-DCE
Avionics Interface Technologies
Single PXI Express Instrument that is reconfigurable to operate as a PXIe-FC4 or a PXIe-DCE module. Save system slots with this instrument by getting both Ethernet (10/100/1000) and Fibre Channel in a single instrument in a single PXI Express Slot.
-
product
Environmental Test Chamber
The chamber is produced by SUS304 Steel, the temperature keeping material is produced by Polyurethane hard foam and ultra-fine fibre glass, the doorframe heat insulated by Double high temperature aging silicone rubber door sealing strip.The temperature controller is used by Korean TEMI display in English/Chinese and German Siemens PLC, it can be communicated to PC via RS-232. The temperature accuracy is 0.1 and humidity is 0.1%R.HThe temperature sensor is platinum PT100 Ohms/MV resistor
-
product
Optical Probes - Low Bandwidth
P6701B/P6703B
Depend on Tektronix to provide you with performance you can count on, and industry-leading service and support.- Broad Wavelength Response 500 to 950 nm or 1100 to 1700 nm- High-bandwidth DC up to 1.2 GHz- High Gain 1 V/mW- Low Noise <11 pW/√Hz- Probe Connects to DPO7000*1 and DPO/DSA/MSO70000*2Series- SONET/SDH and Fibre Channel Reference Receiver Performance
-
product
Linear Equalizers
Macom Technology Solutions Holdings Inc.
MACOM offers high-performance linear equalizers for use in high speed copper connections for Ethernet, InfiniBand and Fibre Channel. The product line supports NRZ and PAM-4 multi-level signal connectivity and builds upon MACOM’s long-standing expertise in equalizers for broadcast video applications. The equalizers can support up to 112Gbps per lane data rates for 50 Gbps to 800 Gbps copper cable assemblies. In addition to copper cables, the linear equalizer can be used for wired backplane and on-board applications. Adding linear equalization to a passive copper cable can enable the same copper cable to carry higher data rates for longer distances. MACOM’s new linear equalizer product line can extend a typical copper cable’s performance to 7.5 meters at 56 Gbps and 5 meters at 112 Gbps data rates. Customers can consider active copper cables as an alternative to passive copper cables or active optical cables. Key benefits include low power consumption from a single 3.3V supply, low latency, hardware and microcontroller management modes. The products are suitable for SFP, QSFP, QSFP-DD and OSFP connector form factors.
-
product
PXI Dual 2 x 2 Fibre Optic (M Mode) STM62.5
40-860-522-M62.5
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
DCA Equivalent-time Sampling Oscilloscopes
Equivalent-time (sampling) oscilloscopes are also known as digital communication analyzers (DCA). They are designed to visualize and analyze the analog properties of high-speed signals used in data center and wireline telecom applications. The Keysight DCA platform features a wide variety of optical, electrical, and TDR/TDT modules, compliance applications, and a common FlexDCA user interface to ensure more efficient testing in both R&D and manufacturing. Due to an ultra-low jitter and low-noise acquisition system, the Keysight DCA series provides industry-leading measurement accuracy for high-speed digital designs including 400G/800G Ethernet and Fibre Channel.
-
product
Variable Optical Attenuator - MATRIQ
The VOA MATRIQ Series is a MEMS-based variable optical attenuator with fast attenuation speed, low insertion loss and in-built power meter. Its advanced power stabilization function lets you set and maintain the output power stability even when the input power fluctuates.It is available in singlemode, multimode and polarization maintaining fibre types and various wavelengths to suit a wide range of applications.With a stackable, space-saving design and intuitive software controls make it a valued addition to the optical lab or test bench.
-
product
PXI Single 4 Channel Fibre Optic Mux FC/PC
40-850-114
The 40-850-114 4-channel multiplexer is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
NVM Express
NVM Express is a scalable host controller interface designed to address the needs of Enterprise, Data Center and Client systems for supporting chip-to-chip, board-to-board, adapter and distance solutions. The protocol can efficiently use interconnect and fabric technologies such as PCI Express, Ethernet and Fibre Channel. Teledyne LeCroy provides protocol analysis, emulation, exerciser and other test equipment to service all NVMe storage applications.
