Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI/PXIe Microwave Multiplexer, Single SP8T, 40 GHz, 50 Ω, SMA 2.9, Terminated, Remote Mount
42-788-051-TE
The 40-788-051-TE (PXI) and 42-788-051-TE (PXIe) are single SP8T 40 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays.
-
product
13 GHz Programmable Attentuator
PA13
This device has low impedance mismatch, high bandwidth, wide dynamic range and is capable of rapid state change. The PA13 can be an attractive alternative to either the manually operated microwave attenuator switches, which are expensive and are switched very slowly, or the relay attenuators which are expensive and wear out quickly.
-
product
Camera Detector
P7030
The easy to use Camera Detector is so small it can be carried or stored anywhere. Discreet sweeps of the home, office or hotel room can be done quickly and efficiently. When a camera is discovered, a LED light flickers and an audible alarm sounds. An auto adjusting sensitivity tuner allows you to scan variable distances and can check multiple channels. It can detect frequencies anywhere from 50 MHz to 3 GHz, picking up most wireless cameras.
-
product
Comb Generator, 10 MHz to 26.5 GHz
U9391C
The Keysight Technologies, Inc. U9391C comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
VDI - Erickson Power Meters
The VDI Erickson PM5 Power Meter is a calibrated calorimeter-style power meter for 75 GHz to > 3 THz applications. It offers power measurement ranges from 1 W up to 200 mW. The PM5 is the de facto standard for > 100 GHz power measurement.
-
product
110 GHz Frequency Extender, Pulsed DC Bias
N5293AX52
The Keysight N5293AX52 is a broadband frequency extension module designed for use with Keysight’s new PNA / PNA-X-based millimeter-wave solutions. It is a compact, lightweight, and ruggedize frequency extender module with built-in bias tee for pulsed DC bias operation. It interfaces with the Keysight N5292A test set controller. The modules allow users to extend the frequency coverage of a base PNA / PNA-X Series network analyzers to a range of 10 MHz to 110 GHz. For more information about cable and accessories for use with network analyzers, please visit Network Analyzer Accessories.
-
product
Infiniium V-Series Oscilloscope: 33 GHz, 4 Analog Channels
DSOV334A
33 GHz analog bandwidth4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with low noise floor (2.09 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
product
PXI Hybrid Coaxial Switch: DC to 40 GHz, Dual Transfer
M9156CH40
The Keysight M9156CH40 PXI hybrid dual transfer switch module provides an exceptional 0.03 dB insertion loss repeatability, high isolation, low SWR with a long operating life up to 10 million cycles.
-
product
PXI RF Multiplexer, 10x SP4T, 1.3 GHz 75 Ω, Multiway Connectors
40-755-210
The 40-755-210 is a 10xSP4T 75 Ω multiplexer and is part of a range of high density RF multiplexers available in 50 Ω and 75 Ω variants with up to 10xSP4T switches in a single PXI module. They are available with two connector options; SMB that provides a frequency range of 1.8 GHz (50 Ω) / 1.3 GHz (75 Ω), or multiway which limits the bandwidth to 1.3 GHz but offers a high density solution occupying one PXI slot. The connectors used are fully supported by the range of Pickering Interfaces connection solutions.
-
product
Streamline Vector Network Analyzer, 100 KHz To 44 GHz, 2-port
P9377B
Compact, faceless, vector network analyzer (VNA). Affordable full two-port VNA which dramatically reduces your size of test. Up to 44 GHz.
-
product
PXIe Microwave Multiplexer, Single SP8T, 26.5 GHz, 50 Ω, SMA, Remote Mount, Failsafe
42-788-041-E
The 40-788-041-E (PXI) and 42-788-041-E (PXIe) are single failsafe SP8T 26.5 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
-
product
ALL-OUTDOOR RADIO SYSTEM
FreeMile 5 GE
SAF FreeMile 5 GE MIMO all-outdoor system is a Licence-free 5 GHz gigabit radio for Ethernet packet data transmission. Making use of ground breaking 2x2 MIMO technology, the SAF FreeMile 5 GE MIMO delivers up to 210Mbps (105Mbps full-duplex) of real throughput combined with a high packets-per-second performance.
-
product
PXI/PXIe Microwave Transfer Switch, Single, 18 GHz, 50 Ω, SMA, Failsafe, Remote Mount
42-782B-521-E
The 40-782B-521-E (PXI) and 42-782B-521-E (PXIe) single failsafe transfer switches with remotely mounted relays are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 18 GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
product
4-in-1 OSLT Calibration Kit, DC to 70 GHz, Type-1.85 mm (m)
CK058M
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
product
Microwave Testing
50A
The GGB Industries, Inc., MODEL 50A probe sets new standards in microwave probing performance. Using low loss coaxial techniques, the Model 50A achieves an insertion loss of less than 1.0 db and a return loss of greater than 18 db through 50 GHz.
-
product
Micro Power or Micro Coax, SIM Insert, ITA, 26 GHz, 2 POS, 6 Slot (not loaded)
510181110
Micro Power or Micro Coax, SIM Insert, ITA, 26 GHz, 2 POS, 6 Slot (not loaded)Micro Power or Micro Coax patchcords need to be purchased separately.
-
product
6U CompactPCI Intel® Atom™ Processor Blade
MIC-3398
The MIC-3398 is a Low-Power 6U CompactPCI® CPU blade with best in class price/performance ratio tailored for applications that require a state of the art processor platform based on Intel® Architecture with full IO capability at an attractive cost point. The MIC-3398 supports Intel® Atom™ E3845 and Celeron N2930, J1900 SoC (system on a chip) family previously codenamed Bay trail with a maximum of quad-core 2.00 GHz processing performance. Intel® Atom™ technology provides significant increases in performance and energy efficiency by using the 22nm Intel® manufacturing process making it an ideal choice for control and workstation applications that require passive cooling with a power dissipation as low as 10W. Up to 8GB, dual channel 1333 MHz DDR3L memory with ECC support provide a high performance and robust memory interface for demanding applications. With built-in graphics based on Intel® HD Graphics Technology this blade offers a significant improvement in graphics performance compared to previous generation platforms. Support for an onboard 2.5” SATA-II drive as well as CFast SSDs adds comprehensive mass storage support. On the system side, the MIC-3398 supports 32-bit, 33MHz and 64-bit, 66MHz PCI bus interfaces to a CompactPCI backplane. A rich set of I/O interfaces such as DVI-D, USB3.0/2.0, Gigabit Ethernet and RS-232/422/485 ports round off the feature set. In addition to the single slot wide (4HP) board offering, a dual slot wide (8HP) version of the blade offers additional network connectivity by increasing Gigabit Ethernet port count from two to four.
-
product
FieldFox Handheld Microwave Analyzer
N9913A
4 GHz max frequency Carry the world's most integrated handheld RF analyzer: standard model includes cable and antenna analyzer Expand capabilities with optional VNA, spectrum analyzer, built-in power meter, vector voltmeter, and more Save time by measuring DTF and TDR in the same sweep Simultaneously measure all four S-parameters Make accurate spectrum analyzer measurements ( 0.5 dB) without warm-up Calibrate simply with QuickCal Lightest all-in-one analyzer at only6.6 lb. (3.0 kg) Industry-leading 3 year warranty Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
cRIO-9049, 1.60 GHz Quad-Core CPU, 4 GB DRAM, 16 GB Storage, -20 to 55 °C, Kintex-7 325T FPGA, 8-Slot CompactRIO Controller
785618-01
1.60 GHz Quad-Core CPU, 4 GB DRAM, 16 GB Storage, -20 to 55 °C, Kintex-7 325T FPGA, 8-Slot CompactRIO Controller - The cRIO-9049 is a rugged, high-performance, customizable embedded controller that offers Intel Atom quad-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 325T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
product
Limiters
Macom Technology Solutions Holdings Inc.
At MACOM we offer a complete line of RF and microwave limiters, LNA/limiters and limiting amplifiers up to 18 GHz. These products use the latest thin-film hybrid manufacturing techniques to obtain the highest levels of performance, repeatability, reliability and cost-effectiveness. Using the latest technology available in the industry for silicon and GaAs FET MMICs, these products are ideal for multi-market and aerospace and defense applications.
-
product
CATV & SAT IF Optical Receiver Module
MRS-26D
Hangzhou Huatai Optic Tech. Co., Ltd.
*Ultra low noise push-pull technology *Band width of 2.7 GHz* 46dB CNR (typ.) for NISC with OMI = 4% at –8dBm optical input power @ 1550nm* 20dBmV RF output level (-5dBm,1550nm,OMI=4%)* Very low intermodulations *Low power consumption *Small package with single-mode fiber pigtail *Integrated optical demultiplexer (WDM filer) for RF overlay applications *Monitor voltage output and output disable input
-
product
Signal Integrity Evaluation up to 50 GHz
N5225BT
The N5225BT provides the N5225B 50 GHz PNA, application software including PLTS and Enhanced TDR and accessories for signal integrity evaluation of cables, backplanes, and BGA packages.
-
product
Radar Level Transmitter
DR5400
DR5400, FMCW 24 GHz open air radar is a market entry level transmitter for liquids in basic process applications. This model has proven PP Drop antenna design which is insensitive to condensation.
-
product
Power Divider, DC to 18 GHz
11636A
The Keysight 11636A is a dc to 18 GHz power divider for direct power dividing applications. The excellent impedance match of all three ports improves fault location measurements by reducing re-reflections. The Keysight 11636A power divider/combiner is recommended when making wideband comparison measurements with a Keysight 8757 scalar vector network analyzer.
-
product
Handheld RF Spectrum Analyzer (HSA), 3 GHz
N9340B
Obtain field-ready performance: portable, rugged, fanless design, clear viewing both day and night, maximum 4-hour batteryGet benchtop performance with 144 dBm DANL, 1.5 dB amplitude accuracy, and < 0.1 s full span sweep timeAchieve powerful measurements: spectrogram, AM/FM/ASK/FSK modulation analysis, AM/FM IBOC measurement, xDSL measurement, and more
-
product
PXI/PXIe Microwave Relay, Single SPDT, 12.4 GHz, 50 Ω, N-Type, Failsafe
42-780B-511
The 40-780B-511 (PXI) and 42-780B-511 (PXIe) are single failsafe SPDT 12.4GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
product
Normally Open, Low PIM, SP3T, SP4T, or SP6T, Multi-Throw Switch, 50Ω Impedance, N Connectors, DC-3 GHz
Part No. CCP-18N
Normally Open, Low PIM, SP3T, SP4T, or SP6T, Multi-Throw switch, 50Ω impedance Available with N connectorsDC-3GHz
-
product
Waveguide Power Dividers
2-way power divider that operates from 220 to 330 GHz. The power divider offers a typical insertion loss of 2.3 dB and typical isolation of 20 dB. All ports are well-balanced and in-phase for power dividing or combining applications across the band. The power divider is configured as a right-angle package with WR-03 waveguides and UG-387/U-M anti-cocking flanges at all ports.
-
product
Adapter, 1.0 Mm (m) To 1.0 Mm (m), DC To 120 GHz
Y1910A
Provides measurement accuracy, versatility, and ease of use for on-wafer and coaxial measurements.
-
product
Hybrid Amplifiers
LNA
Macom Technology Solutions Holdings Inc.
MACOM’s portfolio of hybrid amplifiers cover a frequency range of 10 kHz to 6 GHz. Each amplifier is designed to be unconditionally stable and have excellent cascadability. Our amplifiers are designed using thin film technology and are integrated components that include internal DC biasing circuitry, allowing them to maintain excellent electrical performance over the 55˚C to 100˚C range. Hermetically sealed and screened up to space level, these amplifiers are ideally suited for hi-reliability and mission critical applications.
-
product
2.5G DPSK Demodulator
Optoplex’s Optical DPSK Demodulator, also known as Delay Line Interferometer (DLI), converts phase modulation to amplitude modulation over the entire C+L band in support of data transmission rates of 2.5, 10 or 40 Gb/s. The DPSK demodulator is designed for phase modulated optical communication systems utilized in commercial, defense and space exploration markets. The device plays a key role in improving signal quality and performance to meet the expanding demand for higher data rates and more complex transmission formats within current and next generation systems without major capital expenditure. Optoplex’s DPSK Demodulator is based on a patented free-space optical design, which is compact, athermal and polarization-independent. Themeasured frequency drift over temperature is only ~0.02 GHz/°C for our standard passive device. Further, this DPSK Demodulator exhibits a total polarizationdependent phase shift of less than 2 degrees over the entire operating temperature range with a high extinction ratio. Optoplex’s DPSK Demodulators can be configured to be fully tunable, colorless tunable or purely passive. Dual-Rate DPSK Demodulator is also available.
