Filter Results By:
Products
Applications
Manufacturers
- TEAM SOLUTIONS, INC.
product
PCIe Digital I/O Board, 64 Optically Isolated I/O Channels, 24V
APCIE-1564
32 digital inputs, 24 V, isolated16 interruptible inputs32 digital outputs, 24 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
product
High Performance 50 MHz Dynamic Digital I/O PXI Subsystem
GX5960 Series
The GX5960 digital subsystem represents the highest level of performance available for PXI-based digital instrumentation and features high performance pin electronics and a timing generator / sequencer in a compact, 6U PXI form factor. The GX5960 series consists of the GX5961 clock generator board with 16 driver / sensor channels and the GX5964 driver / sensor board which supports 32 bi-directional I/O channels. Up to 528 digital I/O channels can be supported by the GX5960 digital subsystem. Each digital channel features a wide drive / sense voltage range of -14 V to +26 V (maximum swing of 24 volts) which can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and a load value (with commutation voltage level) – offering the user complete flexibility when creating test programs and fixtures for multiple UUTs. In addition, each channel offers a parametric measurement unit (PMU) for DC measurements.
-
product
ISSRs for Mounting on Printed Circuit Boards
Series LS10
Series LS10 DC solid-state relays are designed for mounting on printed circuit boards. They facilitate heat-sinking by providing an interface surface. They can switch loads with high starting currents. The nominal switched currents depend on the size of the heat sink These relays use a direct-bonded copper substrate for thermal efficiency and long life.Available options include:LS60DC10C-21 10A, 7-36 Vdc Load; 3-10 Vdc ControlLS60DC10F-21 10A, 7-36 Vdc Load; 7-30 Vdc Control
-
product
High Temperature Diametral Extensometers (1000 C)
Model 3580
Jinan Testing Equipment IE Corporation
This model is for diametral strain measurement with furnace and induction heating systems. Quartz rods and water-cooling allow the unit to be used for high temperature testing of metals, ceramics and composites. With induction heating, this model often can be used without water-cooling. When used in furnaces, the extensometer is often mounted directly to the furnace side cut-out. Optional load frame mounting brackets are available for supporting the extensometer in cases where furnace mounting is not possible. These optional mounts are used with induction heating or furnace systems. The Model 3580 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Load Boards
The Hartmann Load Boards were originally designed for in house use to test, setup and qualify standard chassis and custom systems. As demand for these products presented itself, Hartmann answered the call with a lineup of high quality load boards.
-
product
Digital I/O with Per Channel Timing, Programmable Logic Levels and PMU PXI Card
GX5296
The GX5296 offers the most performance and features of any 3U PXI dynamic digital I/O board on the market today. The 32-channel, GX5296 offers timing per pin, multiple time sets, data formatting, and an advanced sequencer – providing users with the capability emulate and test complex digital busses for system, board or device test applications. Offering 1 ns edge placement resolution per pin and a PMU per pin, the GX5296 has the ability to perform both DC and AC parametric testing. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level).
-
product
Single-Inline Package (SIP) Relays
Series LS
Series LS single-inline package (SIP) relays are designed for mounting on printed circuit boards. LS relays facilitate heat sinking by providing an metallic interface surface. The relays use a direct-bonded copper substrate for thermal efficiency, thermal stress performance and long-life expectancy. Optional heat sinks are available.Available options include:LS24D16C 50A, 90-280Vac, 600Vpeak Load; 4-20mA ControlSHP24N50R 50A, 100-280Vac, 600Vpeak Load; 8-30Vdc Control
-
product
Bi-Directional Level Translator
IFB-10001
Easily connect Arduino or other 5V microcontrollers to ~3.3V sensors. Based on the TI TXB0108 auto-sensing, bi-directional level translator, this module provides access to all 8 channels of the TXB0108 and has a built-in 300mA LDO with 200mV max dropout voltage at full load. Regulated 3.3V output allows this single board to both interface withandpower 3.3V sensors. An important feature of this module is the ability to operate SPI and other digital lines (not including I2C) at high-speed, whereas the 'NXP level shifter' maxes out at 400kHz and resistor dividers fail much earlier. The TXB0108, integrated with the LP3981 LDO, provide a fast, reliable solution to mismatched interface voltages that exceeds the performance of other solutions.
-
product
In-Line Full Automatic Testing System
ALMAX
Automated press unit with board loading belt.ALMAX can become automated in-line type in-circuit tester in case our ICT is integrated. And it also can become automated in-line function tester as well.PLC is not used in order to reduce cost as a PC control mechanical part.Press unit is 4 shaft structures which reduce unbalanced load and contact fail of probe pins.
-
product
Load Board
cPCI 6U
Load boards are essential in keeping any system in top running shape. As a full-system provider, Hartmann strives to not only provide the systems you need, but the supporting hardware as well.
-
product
Meter Qualification Board
MQB
Power-up and apply load to electric watt-hour meters for functionality testing with TESCO’s multi-position MQBs. These boards assist with AMI Meter Certification process and AMI meter qualification and communication testing.
-
product
Load Board
cPCI 3U
Load boards are essential in keeping any system in top running shape. As a full-system provider, Hartmann strives to not only provide the systems you need, but the supporting hardware as well.
-
product
Load Cell Measurement
Designed specifically as a single-board solution for material testing system (MTS) applications, the PCI-9524 combines a high 24-bit resolution with 1/200,000 count accuracy to provide the most precise load cell measurement PCI board available in the market today.
-
product
Seam Fold Test Device
FFR1000
This equipment is designed to bend a flexible printed circuit board, which has a high degree of freedom and versatility, and at that time, apply a load to the bending point at the initial stage or each time, and repeat bending and unfolding to confirm the durability.
-
product
Signal Conditioning and Filtering
MSXB 067
The MSXB 067 Signal Conditioning Expansion Board provides analog signal conditioning for strain gauges, load cells, RTDs, and other resistive sensors. MSXB 067 provides a flexible interface for quarter-bridge, half-bridge, and full-bridge sensors, with two to six wires for each sensor, with or without voltage sense feedback. A small daughterboard supports user-supplied bridge completion resistors.
-
product
Universal Relay Driver Control - PXIe, 32 Channel Direct Relay Drivers
33011
PXI-e based universal relay control for semiconductor load boards, 32CH direct relay drivers, 2 lanes of SPI relay control interface
-
product
Digital I/O Board, 32 Isolated I/O Channels, 24V
APCIE-1500
The PCI-Express 32 digital I/O board APCIe-1500 has 32 digital inputs/outputs (24 V or 12 V), 14 inputs are interruptible. The 16 digital power outputs are equipped with protection diodes and filters. The board is fully compatible to the PCI board APCI-1500. It is especially suited for applications like industrial I/O control, signal switching, ON/OFF monitoring of motors, lights etc. in the harsh industrial environment. The APCIe-1500 has interruptible inputs. They supersede continuous cyclical query processes (polling) for routine monitoring and evaluation tasks. This takes load off the processor and the software. At a change of state of the digital inputs the APCIe-1500 generates an interrupt, so that the system reacts on the event through the interrupt routine and herewith fulfils real-time criteria.
-
product
Load Board
cPCI Serial 3U
Load boards are essential in keeping any system in top running shape. As a full-system provider, Hartmann strives to not only provide the systems you need, but the supporting hardware as well.
-
product
Utility Power Source
SE-UDPS
Load boards for applications like mixed signal, analog and RF require active components. To drive these active components multiple utility power supplies are needed. The SE-UDPS from Salland Engineering is an economical way of adding more utility power supplies to your Advantest™ V93K to drive op-amps, buffers, relays and switches. The SE-UDPS extends the usefulness of your current fleet of V93Ks. You can also minimize the need to add external power supplies on your load boards.
-
product
LOAD BOARD
The semiconductor manufacturing process is divided into a front process (WAFER) and a post process (PACKAGE). The LOAD BOARD is an INTERFACE device for inspecting the function and performance of a package state IC, which is a post process, It is an INTERFACE key device for inspection. In particular, LOAD BOARD is widely used in non-memory semiconductor inspection equipment.
-
product
Power Supply Testers
Qmax Test Technologies Pvt. Ltd.
Power Supply Tester is an integrated package of hardware such as AC/DC Power Sources, DC Loads, Noise Measurement Unit, and DMM etc configured as per user applications, which makes it suitable for testing wide range of Power Supplies and provide economic solution for testing AC/ DC and DC/DC power supplies and converters. The Power Supply Boards that passed in the first level of screening for Go-No Go tests will undergo a second level testing. The second level of testing measures all the key parameters of the power supply such as line regulation, load regulation, efficiency etc and check whether the results are within the mentioned limit, if not declare the UUT (Power Supply Board Under Test) as a failed one.
-
product
Meter Qualification Boards
WECO 8020, 8030
WECO Meter Qualification Boards by Radian Research enable extensive functional testing of single-phase and three-phase revenue grade electricity meters. Unlike Warm-up Boards and Load Boards that are limited to just powering the meter or applying a fixed current, WECO Meter Qualification Boards can test a variety of communications, disconnect and safety features. The WECO 8020 and 8030 have varying capabilities based on your requirements. They feature an innovative open socket design exclusive to RADIAN that ensures optimum operator safety. Capability, versatility and safety combine to make WECO Meter Qualification Boards THE logical choice.
-
product
Thermal Load Boards
Thermal Engineering Associates, Inc.
A Thermal Load Board (TLB) is used to simulate an application printed circuit assembly (PCA) either before all the heat-producing components are available for mounting on the application PCA or if the heat-producing components require complex electronic circuitry to create heat within the components. The TLB is typically designed to be as mechanically and thermally equivalent to the application PCA and usually offers a way to vary the power dissipation of the elements that simulate the heat-producing components.
-
product
Darlington Arrays
Darlington devices are high-voltage, high-current switch arrays containing multiple open-collector Darlington pairs or multiple Darlington transistors with common emitters, and integral suppression diodes for inductive loads. The nominal current rating of each output is 500 mA for the 7- and 8-output devices and up to 1.5 A for quad-output devices. The inputs are pinned opposite the outputs to simplify the application board layout. These devices interface standard logic families.
-
product
Test Contactor
MiCon
The MiCon™ Test Contactor is spring pin footprint compatible supporting advanced temperature requirements as well as advanced power/current requirements. The footprint compatibility allows for easy and cost-efficient conversion from spring pin setups. The fully decoupled load board side of the spring ensure no degradation of the load board pad.MiCon features a single piece design, which ensures a long lifespan, low and stable contact resistance, high current carrying capability and an extended temperature range. The MiCon allows for testing at full specification values. The extended operating range accommodates device lead trim and form variability such as device alignment accuracy and device lead coplanarity.
-
product
High Impedance Differential Clock Divider
Alliance Support Partners, Inc.
he ASP-DCD-00 board is a high impedance input clock divider circuit. It is designed to provide minimum load to a clock source for frequency measurement. It accept single ended (Unbalanced) or differential (Balanced) signals with amplitudes as little as 100mV rms; it divides the input signal frequency from 2 to 256 times depending on shunt jumper selections on J3. The board requires 5VDC 500mA power source to operate. The output is capable of driving 5V TTL logic levels.
-
product
Solid-State Inline (SIP) Four-Pin Relays
Series AS4
Series AS4 solid-state single inline (SIP) four-pin relays are designed for mounting on a printed circuit board. The relays offer built-in voltage protection and can withstand very high current overloads. The relays have a low zero-cross window. The compact size and triac output make the AS relay the perfect retrofit for electromechanical relays. All Series AS relays are Zero-Cross switching.Available options include:AS24D4E/R 4Arms, 12-275Vrms, 600Vpeak Load; 4-30Vdc ControlAS24D4E-X1 4Arms, 12-275Vrms, 600Vpeak Load; 6-30Vdc Control; DIN-rail clip+LEDAS24D4E-X2 4Arms, 12-275Vrms, 600Vpeak Load; 6-30Vdc Control; DIN-rail clipAS46D4E/R 5Arms, 12-460Vrms, 800Vpeak Load; 4-30Vdc Control
-
product
SparkFun I2S Audio Breakout
MAX98357A
The SparkFun I2S Audio Breakout board uses the MAX98357A digital to analog converter (DAC), which converts I2S (not be confused with I2C) audio to an analog signal to drive speakers. The I2S Audio Breakout converts the digital audio signals using the I2S standard to an analog signal and amplifies the signal using a class D amplifier which can deliver up to 3.2W of power into a 4Ω load. The board can be configured to output only the left channel audio, right channel, or both.
-
product
High-Voltage, High Current I/O Module
Model JI-4516
The JI-4516 module is a versatile, easy-to-use device for adding high-voltage, high-current digital I/O capability to a computer system via a USB connection. The module is comprised of 8, low-side power MOSFET switches, and 8 high-voltage inputs. I/O ground isolation eliminates ground-loops and provides protection from noise and switching transients during high-current load switching. The JI-4516 is available as either a desktop unit or low-cost OEM board.
-
product
VME/VME64x Load Board
VECTOR Electronics and Technology, Inc.
The 6U VME and VME64x load board functions to test a system’s cooling capability by applying a variable load to the power supply for verification, then generating necessary heat to confirm the chassis’ cooling. This enables locating hot spots in the chassis so the airflow can be properly directed.
-
product
Stainless Steel Junction Box
JB104SS
The JB104SS junction box model is designed to connect and trim up to four load cells per board. It may also be used in combination with additional juction boxes through the use dof an expansion port on the main board to connect multiple junction boxes thus allowing the summing of more than four load cells.
