Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 1.02k Ohm
50-294-021
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
-
product
Bench Power Supply, Linear, Programmable, 1 Output, 0 V, 60 V, 0 A, 2 A
72-2715
The 72-2715 from Tenma is a single channel programmable bench power supply. It is a digitally controlled industrial grade power supply with load for a long time. This compact design power supply has intelligent temperature controlled fan, low noise and low ripple. It also features knob lock function to avoid improper operation. This power supply has load regulation ≤0.01% +2mV (voltage), ≤0.1% +5mA (current) and line regulation of ≤0.01% +3mV (voltage), ≤0.1% +3mA (current). The setting accuracy (25°C ±5°C) is ≤0.5% +30mV (voltage), ≤0.5% +5mA
-
product
Programmable Single Channel DC Electronic Load, 150V/30A/300W
T3EL150303P
Programmable Single Channel DC Electronic Load, 150V/30A/300W.
-
product
High Temperature Axial Torsional Extensometers (1200 C or 1600 C)
Model 7650
Jinan Testing Equipment IE Corporation
Model 7650 extensometers are primarily used on round specimens tested in bi-axial test machines capable of simultaneous axial and torsional loading. All models are capable of bi-directional displacement in both axes and may be used for strain-controlled fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7650 models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to minimize crosstalk between axes and to provide high accuracy, high resolution measurements. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods with conical rod tips for specimen contact when testing to 1200℃(2200°F). Silicon carbide rods are used for the 1600℃ (2900°F) high temperature option.
-
product
DC Power Supplies
SG Series
AMETEK Programmable Power, Inc.
The Sorensen SG Series (hereafter SG Series) represents the next generation of high power programmable DC power supplies. The SG Series is designed for exceptional load transient response, low noise and the highest power density in the industry. With a full 15 kW available down to 20VDC output in a 3U package the SG Series leads the industry in power density. The power density is enhanced by a stylish front air intake allowing supplies to be stacked without any required clearance between units.
-
product
16CH Battery Cell Simulator
Chroma 87001
Chroma Systems Solutions, Inc.
Chroma 87001 Battery Cell Simulator is a high precision, programmable, and bidirectional DC power source with both voltage source and current source functions. In addition, the model can be used as a multi-channel DC power supply or an electronic load as well. A single simulator has 16 channels and each of them can set voltage and current respectively via Chroma software.
-
product
Bidirectional Programmable DC Power Supply(5kw ~ ±180kW)
FTB9000 Series
Shenzhen FaithTech Technology Co., Ltd.
FTB9000 series is a regenerative bidirectional programmable DC power supply, it is not only a stand-alone bidirectional DC power supply but also can be used as a regenerative electronic load, to absorb the consumed energy and feedback cleanly to the grid. The high-efficiency energy feedback efficiency not only saves electricity consumption and heat dissipation costs but also does not interfere with the operation of the power grid. It is widely used in high-power testing scenarios such as automotive electronics, new energy vehicles, photovoltaic energy storage, intelligent industrial equipment, battery simulation, etc.
-
product
PowerSync Programmable Load
Lower cost solutions for versatile 802.3at and 802.3bt Powered Device Emulation to support PSE system test and analysis
-
product
PXI Programmable Power Supply, 0-48VDC
41-743-001
The 41-743 is a fully isolated programmable power supply capable of delivering output voltages to 48V with a voltage setting resolution of less than 1mV. The output is capable of delivering up to 40W to the user load and requires no external power supply – power is drawn from two PXI backplane slots.
-
product
Controllable, Programmable Linear DC Source With Load
LAB / SL
*Linear laboratory power supply*Integrated electronic load*Linear regulated DC laboratory power supply*No thyristor pre-regulation, very little ripple*Various interfaces · Built-in electronic load*Protection against short circuit, overload and overtemperature*Constant current and constant voltage*Fast control times approx. 250 µS
-
product
Modular Power
RFP DC High Power
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
product
Electronic Loads
PeakTech Prüf- und Messtechnik GmbH
Can be used for important test procedures in quality assurance as well as e.g. testing of power supplies and control units, batteries, fuel and solar cells. For precise load control for various purposes, this device offers load control according to constant voltage (CV), constant current (CC), constant load resistance (CR) or constant power (CP) with a highly precise resolution of 1mW, 1mV, 1mΩ and 1mA. The device also offers additional test modes, e.g. the battery test or the dynamic test. The PC interface and software offer the option of implementing freely programmable test sequences with data evaluation.
-
product
4 Discrete/Switch I/O Channels (±100 V, 3 A/Ch.)
DT3
The DT3 module (the enhanced version) feature 4 independent, high current, isolated, programmable channels that can be used for input voltage measurements (±100 V), or as a bi-directional current switch (up to 3 A per channel). When programmed as a switch with the switch closed, both the current through the switch and the voltage across the switch can be monitored. These modules include diode clamping on each channel. Clamping is useful for inductive loads, such as relays and short circuit protection.
-
product
Digital I/O Module
ND-6050
- Interface: RS-485- 7 TTL digital inputs- 8 open collector DO- Output up to 30V, 30mA max. load- Programmable input polarity
-
product
Electronic Loads
SLH AC/DC
AMETEK Programmable Power, Inc.
From the leader in programmable power products, Sorensen introduces the SL series electronic loads which offer the best value with the most flexible platform. A wide range of loads are available from 75-1800W with both DC and AC input in benchtop, modular and standalone form factors.
-
product
Modular Power
RFP DC Load
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
product
Amplified Torque & Load Cell Indicator
9834
For use with amplified load cells and rotary torque sensors. Features 120 readings per second, programmable +/-10V or 4-20mA analog output, peak and valley monitoring, RS232. Packaged in an aluminum 1/8 DIN, panel mountable enclosure with a plug-in AC power cord. Sensor connection via 9-pin connector.
-
product
PXIe-4331, 102.4 kS/s, 24-Bit, 8-Channel PXI Strain/Bridge Input Module
781345-01
102.4 kS/s, 24-Bit, 8-Channel PXI Strain/Bridge Input Module—The PXIe‑4331 is a high-speed input module that provides integrated data acquisition and signal conditioning for dynamic strain, load, and pressure measurements. This module includes increased accuracy, high data throughput, and synchronization features, making it ideal for high-density measurement systems. To remove noise, the PXIe‑4331 offers antialiasing and digital filters per channel. Each channel also features an independent, programmable excitation voltage. Additionally, the PXIe‑4331 provides remote sensing, internal bridge completion, and shunt calibration options per channel.
-
product
Electronic Loads
SLM AC/DC
AMETEK Programmable Power, Inc.
From the leader in programmable power products, Sorensen introduces the SL series electronic loads which offer the best value with the most flexible platform. A wide range of loads are available from 75-1800W with both DC and AC input in benchtop, modular and standalone form factors.
-
product
Programmable Single Channel DC Electronic Load, 150V/30A/200W
T3EL150302P
Programmable Single Channel DC Electronic Load, 150V/30A/200W.
-
product
Medium Power Programmable DC Electronic Load(600W~3000W)
FT63200A/E
Shenzhen FaithTech Technology Co., Ltd.
The FT63200A/E series of Medium power programmable DC electronic load is designed for high reliability and high power density. It can achieve 2U/3kW, which is twice of the power density of the conventional load. The FT63200A/E series has three voltage ranges of 150V, 600V and 1200V, with a single power range from 750W to 3kW. Its wider working range, extremely fast dynamic frequency, effectively increase the testing capability and application range. The whole series of products have strong overload capacity, instant over power pull up to twice the rated power, can effectively reduce the test cost.
-
product
Programmable Oscillator Amplifier
Computer Conversions Corporation
The Computer Conversions Corporation POA90-3 is a programmable quadrature oscillator with a built-in power amplifier, capable of driving current loads of up to 200mA. The sinusoidal outputs are 2.5Vrms signals that are phased 90° apart as REF out and REF out +90 (Quadrature), allowing the unit to be used with Synchro, Resolver, LVDT/RVDT, Inductosyn, or similar inductive transducers.
-
product
Programmable DC Electronic Load
Programmable DC electronic load is a device that precisely regulates the load voltage and current dissipation power consumption of electrical energy. There are several important parameters to consider when choosing programmable DC electronic load, including maximum power, maximum current, maximum voltage, current slope, and so on. Each indicator is related to the needs and applications we actually test.
-
product
Electronic Loads
SLH DC
AMETEK Programmable Power, Inc.
From the leader in programmable power products, Sorensen introduces the SL series electronic loads which offer the best value with the most flexible platform. A wide range of loads are available from 75-1800W with both DC and AC input in benchtop, modular and standalone form factors.
-
product
FaithTech Regenerative High-power Programmable DC Load
FTR9000 Series
Shenzhen FaithTech Technology Co., Ltd.
FTR9000 series is a regenerative programmable DC electronic load. It not only has the function of traditional consumable load, but also cleanly feeds the energy consumed by traditional load back to the power grid to achieve the purpose of energy conservation. It can be widely used in new energy equipment testing, lithium ion, fuel and other battery discharge testing, automatic testing system, AC/DC, DC/DC and other one-way module product testing and aging. The product is equipped with rich communication, programming interfaces, color screens and a variety of text menu interfaces, which is easy to operate and intuitive. It is a common equipment in the power electronics, new energy, sensors, motor drives, system integration and other industries.
-
product
DC Electronic Load
Siglent SDL1000X series Programmable DC Electronic Load features an input range up to 150V/30A/300W. CC Dynamic mode frequency is up to 25 kHz. It delivers stability over a wide range of applications and can meet all kinds of testing requirements including: Power, battery/handheld device design, industry, LED lighting, automotive electronics, and aerospace.
-
product
Signal Splitters
The DAT4530 can convert any process signal (Thermocouples, RTD, mV, Voltage, mA Resistance and Potentiometer) to a voltage or current output (4-20mA, 0-20mA or 0-10V). Each output can be different and it also has a built in limit alarm which is an SPST relay. The DAT4530 is PC programmable with the aid of the Prodat programmer and the Datasoft software which is available from the Datexel down load page. The DAT4530 is also programmable with the aid of 3 DIP switches which can be found on the side of the DAT4530. There is full isolation between the input, power supply, limit alarm output and two outputs.
-
product
Test System
Maynuo Electronic Co.,Ltd a professional R & D and production of programmable DC electronic loads, programmable DC power supply, high power load, power supply, AC power supply, power supply, such as testing high-performance mobile phone test equipment and facilities, as well as electrical, electronic, aerospace, military, chemical, automotive, battery charger, battery, solar cell production lines and other industries to provide automated testing program. The company has many years experience in a number of outstanding technical R & D, product innovation by the majority of users. We are committed to provide users with more accurate and more stable more easily accessible to the higher cost of test instruments, to create the industry in testing the influence of an international brand of excellence.
-
product
Programmable DC Electronic Loads (conventional and regenerative)
Elektro-Automatik GmbH & Co.KG
Our programmable electronic loads are composed of an optimum mix of analogue- and digital technology (µ-controller/FPGA based). By combination of standardised electronic platforms out of a modular structure, we generate a large portfolio of electronic-load series, perfectly adapted in power, function, performance and cost to the numerous applications in industrial environment and R&D. EA programmable electronic loads are available in conventional technology (heat dissipating) and as “regenerative” loads. The latter allows, specifically under long-term testing condition (e.g. battery discharging) a full amortisation of its invested value by its energy-saving capability, similar as with Photovoltaic installations.
-
product
PXIe-4051 - PXIe, 1-Channel, 60 V, 40 A PXI Electronic Load Module
788179-01
The PXIe-4051 provides programmable load capable of sinking DC power for characterization, design validation, and manufacturing test. This module helps you sink current and absorb power out of a power source up to 300 W with programmable constant voltage, current, resistance, and power levels. You can use the PXIe-4051 to streamline the task of designing automated test systems for a wide range of applications—from aerospace and defense to automotive and semiconductor component test—by eliminating the need to mix multiple instrumentation form factors in a given test system and simplifying synchronization.
