Filter Results By:
Products
Applications
Manufacturers
- Valhalla Scientific Inc.
product
Digital Igniter Tester
Alpha 4314
The Alpha 4314 Digital Igniter Tester is a portable digital ohmmeter which has been specifically designed for ultra-safe resistance testing on explosive devices (i.e. squibs, detonators).
-
product
Network Test LanCaster Pro ST
The NEW Lancaster Pro-ST is a low-cost wire map tester which tests and certifies structured cabling continuity to a TIA568A/B, USOC and ISDN standards. The new Lancaster Pro-ST displays on screen wiring configurations showing the length of all 4 pairs and length of pair to fault up to 150m (500ft).
-
product
Telephone Line Tester for ISDN Lines
1EA065
ISDN line checker shows the correctness of your ISDN So bus line connections. Indication of the problem is presented with 4 LED (combination of them shows different states and working conditions of the ISDN So bus). The tester uses Phantom power - no need for additional power supplay.
-
product
Line Tester
CAT 1 TEST
Monacor International GmbH & Co. KG
Line tester for continuity testing of Cat 5, Cat 6 and ISDN network cables*Connection test with LED display for 8 individual wires and shielding*Continuity, miswire, open, short, crossover, and ground detection*Connector compatibility with the following modular plugs: RJ45 (8P8C), RJ12 (6P6C), RJ11(6P4C, 6P2C)*Network standards supported: Token Ring, 10Base-T, 10Base-T2, 285A, TIA568A/568B*Separate receiver for particularly long and complex cables*The main unit and separate receiver can be attached to one another using a guide rail on the side*Power supply via 9 V block battery (not included)*Supplied with protective bag
-
product
LAN Tester / Wiremap Tester & Cable Fault Locator
RapidTrace 700
Compact, Powerful and Easy to use. This high performance low cost LAN Tester / Wiremap Tester and Cable Fault Locator is the perfect tool to enable you to test and certify structured cabling continuity to TIA568A/B, USOC and ISDN standards.
-
product
Call Generator (Voice / Data)
Qosmotec Software Solutions GmbH
The Mobile Network Tester LTS is an automatic call generator, that establishes voice and data calls to and from actual mobile devices in the test system. Voice calls can be generated via the wireless PLMN network using actual mobile devices, via the PSTN network through analogue or ISDN lines or via Voice over IP. Wireless data sessions can be setup through the 3G or 4G network or over WiFi.
-
product
ISDN-Testers
Is an ISDN Tester for use in the installation and maintenance of BRI S/T/U and POTS accesses – including BRI S/T NT and monitor modes.
-
product
PAM4 Bit Error Rate Tester.
BERT-1102
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
product
MTM-Bus Tester
PXIe-1149.5
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
product
Bit Error Rate Tester - PXI
BERT 1001/1005 Series
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
KVS Rugged Igniter Tester With Current Monitor
4314
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
product
Bit Error Rate Tester - MATRIQ
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
Automated Coherent Receiver Tester
CoRx Tester.
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
product
ISDN Chip Set
Emutel Symphony
Emutel Symphony is a convenient and flexible Basic Rate ISDN, Primary Rate ISDN and Analog PSTN network simulator. With support for S, U, E1, T1 and PSTN analog interfaces you can use the Emutel Symphony to test and develop a full range of ISDN(E1/T BRIS BRIU) and PSTN analog (FXS) equipment.
-
product
2 PRI + 16 BRI-U ISDN Simulator
CH-16BRI-U-MOD-2PRI
This unit has two PRI ports and 16 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network
-
product
4 Port T1/E1/PRI ISDN Simulator
SIM-4PRI
The most inexpensive ISDN simulator on the market. This unit has four PRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network.
-
product
8 Port BRI-U ISDN Simulator
BRI-8U
The unit has 8 U ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
-
product
2 PRI + 16 BRI-S/T ISDN Simulator
CH-16BRI-ST-MOD-2PRI
This unit has two PRI ports and 16 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network
-
product
8 Port BRI-S/T ISDN Simulator
BRI-8ST
The unit has 8 S/T ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
-
product
Basic Rate ISDN and IDSL Network Simulator
Emutel Solo
Emutel Solo is a small, portable lightweight battery powered basic rate ISDN and IDSL network simulator. With 2 software switchable S/U interfaces and the choice of either Euro-ISDN, North American or NTT support. Emutel Solo allows you to test and demonstrate all types of BRI equipment on one compact unit. Providing all the standard features but also many others that its compeditors don't include.
-
product
2 Port BRI-S/T-U ISDN Simulator
BRI-2UST
The unit has two S/T and two U ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
-
product
Rub Tester and Abrasion Tester
RT4
This comparative test works by abrading a printed sample against a reference material under known conditions. The results can be used to identify alternative substrates, better ink and coating formulations or the suitability of finished cartons, films or printed books, magazines and promotional materials.
-
product
Qualification Tester
LQ404
Computer Gesteuerte Systeme GmbH
The qualification tester LQ402 is designed to support up to 12 DUTs (Device under Test), for which the loads are installed in separate load boxes. The system consists out of 3 cabinets. One is for the electronic components with the primary measurement devices and the other two hold the 12 load boxes.
-
-
product
Multifunctional testers
MI 3152 EurotestXC
MI 3152 EurotestXC is an instrument from the new generation of Metrel’s multifunctional measuring instruments. The already well known functions like complete installation safety testing according to IEC/EN 61557 and AUTO SEQUENCE testing of TN, TT and IT earthing systems are managed by a completely new user interface based on large colour touch screen display. A wide range of functions is included: from on-line voltage monitoring, phase sequence testing, varistor testing, earth resistance measurement, illuminance measurement and TRMS current measurement up to RCD tests, line and loop impedance tests, specific earth resistance measurements as well as ISFL measurements and the IMD tests.
-
product
Insulation Testers
The Zeta series consist of the insulation testers. Zeta series insulation testers have proven invaluable in the testing of insulation resistance measurement for industrial applications such as motors, electrical panels, cables, telecom industry, defense and many more.
-
product
EMI Tester
The EMI tester automatically measures the noise distribution of the electric field and the magnetic field radiated from electronic equipment with high accuracy.・ Even if PCB and IC parts have complicated bumpy shape and surface. The movable assembly can automatically trace them.・ EMI noise distribution is expressed as a variety of maps, such as 4D/3D/2D graphics and cross section view.
-
product
Motor Testers
Changzhou Chanlon Electronic Technology Co., Ltd.
This machine is applied to test steel casing motor such as pump, fan, air-condition motor, mower, paper shredder and refrigerator etc. Its LCD shows all technical data which obtained by industrial control computer, which check and verify the quality of testing stator.
-
product
EMF Testers
Shanghai Beha Electronics Co., Ltd.
*Handy EMF tester*Digital EMF Tester for Measurement of Magnetic Field Strength*direct display in Tesla or Gauss*Measurement Range:0...199,9 μT0...1999 mG
-
product
Peel Testers
Imada offers motorized peel testers in vertical or horizontal configurations.The motorized test stand, digital force gauge and peel fixture apply tension to a safety seals, tapes and laminates.Special attachments and fixtures facilitate 45°, 90°, 180°, ‘T’ and rotary peel tests.Motorized peel testers offer speed control and highest degree of repeatability with the ability to set a constant test speed and range of movement.All peel testers with digital force gauges have data output capability for analysis by optional data acquisition software.
