Filter Results By:
Products
Applications
Manufacturers
LTE
Long Term Evolution with 100Mbit/s downlink, 50Mbit/s uplink and < 10 ms ping.
See Also: LTE-Advanced, LTE-M
-
product
LTE RRM Test System
T4010S
The T4020S LTE RRM tester is the Keysight platform for LTE RRM conformance testing of LTE UEs. T4020S belongs to the Keysight LTE product family and, as the other LTE T4000S test platforms, is based on the T2010A LTE Wireless Communications Test Set.
-
product
Test Automation Platform / LTE, GSM and WCDMA
MLT1600
The MLT1600 addresses the testing challenges of IoT products across multiple cellular radio technologies – such as GSM, WCDMA and LTE – with a 70-MHz to 6-GHz frequency range. With its portable design and small footprint, the MLT1600 leverages W2BI’s existing cloud-based test management platform to acquire on-demand test cases and publish test results as required across all test parameters.
-
product
Spectrum Analyzer
S3531
Saluki S3531 series RF spectrum analyzer is designed based on the concept “Smaller, lighter, easier” . S3531 series takes a small desktop space and easy to carry. Most of nowaday RF applications are in this band, like mobile communication (GSM, CDMA, LTE even low frequency 5G), WIFI (2.4GHz), remote control etc, so S3531 series is a good tool for the test, maintenance, R&D of these applications.
-
product
FieldFox C Handheld RF Analyzer, 4 GHz
N9913C
Capture elusive signals with up to 120 MHz gap-free, real-time bandwidth. Measure all four S-parameters simultaneously with 115 dB dynamic range. Make accurate spectrum analyzer measurements (± 0.3 dB) without warmup. Perform over-the-air measurements for 5G NR and LTE. Use GPS/GNSS for geolocation and timestamping.
-
product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781339-03
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781775-03
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
product
Network Test and Security
Ensuring high performance of wired, Wi-Fi, and 3G/4G/LTE and 5G networks in both pre-deployment and real-world environments while enabling dynamic security intelligence to help stay one step ahead of attacks.
-
product
Boards, Blades, and Appliances
Adax Signaling Controllers; DPI, IPsec and GTP Packet-Processing Accelerators for LTE, 3G and IMS; 1U and 2U Communications Appliances; and Security Gateways.
-
product
DAS / 4G LTE Power Dividers, Combiners
INSTOCK Wireless Components, Inc
INSTOCK Wireless offers wideband RF power divider / combiners optimized for DAS (Distributed Antenna System), 3G, and 4G LTE modem gateway splitting applications. INSTOCK cell-band and DAS splitters are commonly used for in-building wireless (IBW) network deployments. Available in 2-way thru 48-way configurations spanning 698-2700 MHz with exceptional performance. Type N, SMA, TNC, BNC, and QMA connector configurations INSTOCK.
-
product
SparkFun LTE GNSS Breakout
SARA-R5
The SparkFun SARA-R5 LTE GNSS Breakout is a robust development tool for u-blox's impressive SARA-R510M8S module. The SARA-R510M8S combines u-blox's UBX-R5 cellular chipset with their M8 GNSS receiver chipset to provide a 5G-Ready wireless IoT device complete with positioning data all on a single chip. As an asset tracker, the LTE GNSS Breakout offers Secure Cloud LTE-M communication for multi-regional use and has an integrated u-blox M8 GNSS receiver for accurate positioning information.
-
product
14th Gen Intel® Core™ Ultra 7/5-Based Advanced Embedded Box PC
EMP-520 Series
- 14th Gen. Intel® Core™ Ultra 7/5 Processors (Meteor Lake-H/U)- DDR5-5600MHz up to 96GB (48GB per DIMM)- 4x independent displays support EDID Emulation- 2x 2.5GbE, 1x COM, 6x USB ports, Type C Thunderbolt (optional)- 2 x Wi-Fi/BT/LTE antenna holes- M.2 2280 (SSD), M.2 3042 (LTE), M.2 2230 (Wi-Fi/BT)- VESA mount (optional)
-
product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781426-03
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
product
GNSS Modular Receiver
R750
Save time, money and headaches with the Trimble R750 GNSS Modular Receiver, Trimble's reliable, easy-to-use base station solution. With remote monitoring and alerts, an internal radio, LTE modem and rover capability, the R750 is designed to meet all your needs.
-
product
Digital Signage Player With 8th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, 3 HDMI 2.0, 4 USB And GbE LAN
DSP500-523
*8th gen Intel® Core™ i7/i5/i3 & Pentium® processor (Coffee Lake)*2 DDR4-2400 SO-DIMM for up to 32GB of memory*3 HDMI 2.0*4 USB 3.1 and 1 GbE LAN*1 M.2 Key E 2230 for Wi-Fi/BT*1 M.2 Key B 3042 for 4G LTE*1 M.2 Key M 2280 for storage
-
product
5G Switch LNA Modules
Macom Technology Solutions Holdings Inc.
MACOM offers a complete portfolio of high-power switch and LNA modules to cover many sizes and classes of 5G base stations, including Macro Cell, Small Cell, and massive-MIMO AAS in frequency bands up to 6GHz. SOI-based switch modules with up to 20W LTE power handling are extensively used in mMIMO and Small Cell radios, and MACOM proprietary PIN diode Switch modules with up to 160W LTE power handling are widely deployed in Macro radios. Featuring ultra-broadband, low noise figure and excellent power handling and reliability, the family of Switch LNA modules are also well suited for a variety of TDD based communication systems in commercial and military applications.
-
product
Mobile Amplifiers
Qorvo's amplifiers for mobile products include multi-mode multi-band power amplifiers (MMPAs) and other integrated front-end modules that span a variety of wireless standards and support 3G, 4G and LTE.
-
product
GPS Clock
TK 42
A reliable and accurate GPS clock for LTE. The TK 42 is a plug-in board specifically designed for use in Long Term Evolution (LTE) cellular network base stations.The clock outputs 10MHz and 1PPS differential signals and will continue to operate in extreme temperature variations. The clock has typically 5 s of drift in a 24hr period whilst under holdover.
-
product
MXG X-Series RF Vector Signal Generator, 9 kHz to 6 GHz
N5182B
Take your designs to their limit with outstanding hardware performance, including unmatched phase noise & spurious characteristicsDrive power amplifiers & characterize nonlinear behavior with industry-leading ACPR & output powerTest wideband devices with factory-equalized 160 MHz RF bandwidthReduce the time spent on signal creation with Signal Studio software, including LTE, WLAN & GNSSLower your cost of ownership with 3-year cal cycles & comprehensive solutions for self-maintenance
-
product
FieldFox Handheld RF Analyzer, Up To 10 GHz
N9912C
Select from cable and antenna analyzer (CAT), Vector Network Analyzer (VNA), and/or Spectrum Analyzer with desired maximum frequency. Capture elusive signals with up to 40 MHz gap-free, real-time bandwidth. Measure all four S-parameters simultaneously with 115 dB dynamic range. Make accurate spectrum analyzer measurements (± 0.3 dB) without warmup. Perform over-the-air measurements for 5G NR and LTE. Use GPS/GNSS for geolocation and timestamping.
-
product
Anite Application Testing
Verify higher level protocols and application enablers for a more effective roll-out of LTE-IMS based services to end-usersPerform rapid and cost-effective application testing associated with device acceptance test plans mandated by major mobile operators such as China Mobile, Verizon Wireless, AT&T and T-MobileGain access to comprehensive IMS LTE test plans mandated by standardization organizations such as GCF and PTCRB
-
product
400 MHz to 4.4 GHz, GPS-Disciplined OCXO, Reconfigurable USRP Software Defined Radio Device
783151-01
400 MHz to 4.4 GHz, GPS-Disciplined OCXO, Reconfigurable USRP Software Defined Radio Device - The USRP-2952 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless communication systems. Built on the LabVIEW reconfigurable I/O (RIO) architecture, USRP RIO delivers an integrated hardware and software solution, so researchers can prototype faster and shorten time to results. You can prototype a range of advanced research applications that include multiple input, multiple output (MIMO); synchronization of heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding. The USRP-2952 is equipped with a GPS-disciplined 10 MHz oven-controlled crystal oscillator (OCXO) reference clock. GPS disciplining delivers improved frequency accuracy and synchronization capabilities.
-
product
Baseband Signal Generator
Find the right T&M solutions for applications requiring baseband signal generation. Our product portfolio includes the well-established baseband generator, supporting many wireless standards such as WCDMA, LTE, HSPA and WLAN802.11a/b/g/n/ac, using WinIQSIM2™. Our solutions selection also includes function generators.
-
product
MIPI Radio Front-End
RFFE
Mobile phone radios have developed into highly complex, multi-band and multi-standard designs that often have multiple radio frequency (RF) signal chains. The MIPI Alliance Specification for RF Front-End Control Interface (RFFE) was developed to offer a common and widespread method for controlling RF front-end devices. The RFFE Master IP core typically resides in the RFIC in a mobile platform, and utilizes the RFFE bus to identify, program and monitor the registers in RF front end Slave devices through programmed IO. It is designed to support existing standards such as LTE, UMTS, HSPA and EGPRS, and is usable in configurations ranging from single Master/single Slave to multi-Master/multi-Slave.
-
product
Conformance Test System
TS-RRM
The R&S®TS-RRM 5G and LTE test system is a test solution for running 5G NR and LTE inter-RAT RRM test cases for certification of wireless devices.It is a fully automated conformance test system for running validated RRM conformance test cases. In addition to the RRM test cases required by GCF/PTCRB, the R&S®TS-RRM also supports carrier acceptance specific RRM tests.
-
product
IMS-SIP Network Emulator Software
E6966B
Wireless telephony networks are increasing capacity for high throughput Internet Protocol (IP) packed-data by utilizing radio access technologies such as LTE and HSPA. Session Initiation Protocol (SIP) and IP Multimedia Subsystem (IMS) are progressively being adopted as part of the network infrastructure to carry traditional wireless telephony services over an all-IP network. SIP provides control of communication sessions whilst IMS is the framework that allows delivery of multimedia services over IP. With this new capability comes the need for developers and operators to move their focus to testing user equipment (UE) in this new network environment.
-
product
Edge Gateway
Arm-based industrial gateways are based on NXP, Qualcomm, Rockchip, and TI, delivering LTE, 5G and Wi-Fi with wide operating temperature range.
-
product
Real-time RF Channels Simulator
RF-LiveSim
Covering a frequency range from 50 to 900 MHz, RF Live Simulator can emulate RF channels propagation modes in real-time for a signal bandwidth from 20 kHz to 20 MHz (gaussian noise, multipath, Doppler and frequency drift tools). RF-LiveSim is a cost effective solution for intense automatic non regression tests at the physical layer level. RF-LiveSim includes 1x RF input and 1x RF output ports, and provides a complete set of channel models, either for fixed or mobile propagation environments. Whatever the standard, any type of receiver can be tested. Thanks to its real-time process, from your basic original signal, RF-LiveSim can perform, for instance, efficient regression testing of LTE solutions to check the good behavior and the limits of your receiver when multipathes, Doppler and Gaussian noise are applied.
-
product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781259-01
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
product
CAN Data Logger
Rebel LT
The Rebel LT is an intermediate level CAN 2.0 data logging solution with the options to upgrade to GNSS with high meter level accuracy and 4G LTE. In addition these data loggers have 4 high speed analogue input channels and 3 digital I/O as standard.
-
product
Desktop Network Appliance Platform With AMD G-Series Processor GX-210 (LX Family) And 4 LANs
NA130
The NA130, a cost-effective desktop network appliance platform with four LANs, powered by the low power consumption AMD G-Series GX-210 processor. This slim-type network appliance is perfect for space constricting environments while also providing reliability, flexibility, scalability and cost effectiveness. The feature-rich NA130 comes with four Gigabit Ethernet ports to enable super-fast connections and supports one optional pair of LAN bypass to ensure continuous network communication. Moreover, it features two PCI Express Mini Card slots - one with USB and another with SATA interface - enabling the addition of Wi-Fi/3G/4G/LTE wireless cards for extensive communication options,
