Filter Results By:
Products
Applications
Manufacturers
-
product
Tabletop Mask Aligner
Model 200
The OAI Model 200 Mask Aligner is a cost-effective high performance mask Aligner that has been engineered with industry proven components that have made OAI a leader in the photolithography capital equipment industry. The Model 200 is a tableop mask Aligner that requires minimal cleanroom space. It offers an economic alternative for R&D, or limited scale, pilot production. Utilizing an innovative, air bearing / vacuum chuck leveling system, the substrate is leveled quickly and gently, for parallel photo mask alignment and uniform contact across the wafer during contact exposure. The system is capable of one micron resolution and alignment precision.
-
product
Tabletop Front & Backside Mask Aligner
Model 200IR
The OAI Model 200IR Mask Aligner is a tabletop system that requires minimal clean room space. It is a cost-effective alternative for R&D or limited scale, pilot production. Utilizing an innovative, air bearing / vacuum chuck leveling system, the substrate is leveled quickly and gently, for parallel photo mask alignment and uniform contact across the wafer during contact exposure. The Model 200IR Mask Aligner is capable of one micron resolution and alignment precision. It has an alignment module which features mask insert sets and quick-change wafer chucks that enable the use of a variety of substrates and masks without requiring tools for reconfiguration. The alignment module incorporates micrometers for X, Y, and z-axis.
-
product
Automated Front & Backside Mask Aligner System
Model 6000
With over 4 decades of manufacturing in the semiconductor industry, OAI meets the growing challenge of a dynamic market with an elite class of production photolithography equipment. Built on the proven OAI modular platform, the Model 6000 has front and backside alignment that is fully automated with a submicron printing capability as well as submicron top to bottom front side alignment accuracy which delivers performance that is unmatched at any price. Choose either topside or optional backside alignment which uses OAI’s customized advanced recognition pattern software. These Mask Aligners have OAI’s Advanced Beam Optics with better than ±3% uniformity and a throughput of 200 wafers per hour in first mask mode, which results in higher yields. The Series 6000 can handle a wide variety of wafers from thick and bonded substrates (up to 7000 microns), warped wafers (up to 7 mm-10mm), thin substrates (down to 100 micron thick), and thick photo resist.
-
product
Large Substrate Mask Aligner
Model 6020
The Model 6020 is a large substrate Production Mask Aligner or Auto-flood Exposure System for RDL First Level Advanced Packaging (PLP) and markets requiring exposure of large glass panels. It is engineered with OAI’s precision, reliability, and quality that is found in all of OAI’s products. The features include wedge effect leveling, superb process repeatability, ≤ 2.0µm printing resolution, and remote diagnostics. Using robotic handling, the system can stand alone or be fully integrated with photo resist processing.
-
product
Traffic Photo Enforcement
LidarCam 2
Automatically collect a video + multiple high-resolution photos every time you capture a traffic violation. Built-in Automated License Plate Recognition (ANPR/ALPR) Technology can automatically check for wanted plates or other violations. Hand-held or mounted to a tripod, in a patrol vehicle or from the side of the road, the Stalker LidarCam 2 is the next generation of photo enforcement.
-
product
MASK DR-SEM
Our defect review SEM tools perform detailed reviews of minute defects on photomasks.
-
product
Testing Solutons for Facial Masks
Guangzhou Biaoji Packaging Equipment Co., Ltd.
GBPI offers mask testing machines for surgical face masks, N95 masks, Melt-blown fabric. BFE Tester, PFE Tester, N95 Tester, Melt-blown fabric Tester
-
product
Photo Detectors
Our photo detectors are offered for both power or energy measurements. Measure as low as a few femtojoules in energy or a few picowatts in power, thanks to our highly sensitive sensors and performant electronics.
-
product
Medical Face Masks Flammability Tester
Sataton Instruments Technology CO., Ltd
Medical face masks flammability tester is to determine the fire resistance performance of medical face masks and full face masks. The tester can provide a specific flame and make the dummy head with facepiece move to the flame under a specific speed. The operator can observe the effects of the flame on the masks and facepiece. The tester is suitable for medical face mask, respiratory protective equipment and full face masks.
-
product
Automated Mask Aligner with Integrated Mask Changer
Model 6000A-MC
The Model 6000A-MC is a precision system combining OAI’s Model 6000, Automated Production Mask Aligner, with an integrated mask changer. The mask changer can handle from 10 to 150 masks. Ideal for both semiconductor and bio-tech applications. It also is designed with a bar code reader to assure each mask is coordinated to the right process. Please contact OAI for further product information.
-
product
DUV Mask Aligner
Model 200E
OAI’S Model 200E DUV Mask Aligner performs all the functions of the tabletop Model 200 Mask Aligner but utilizes a 185nm Excimer Lamp as the UV light source. It is used for Biotechnology Processing.
-
product
Photo Type Tachometer
DT-2234A
MEASUREMENT RANGE:2.5～99,999r/min. ACCURACY:±(0.05%n+1d) . POWER SUPPLY:4X1.5V AA(UM-3)BATTERY
-
product
Photo Detector Testing
With the rise of 5G technology and popularization mobile devices, more and more advanced photoelectric sensors are used in our daily lives. In order to be better applied to mobile devices, the photosensitive area of these advanced photodetector is getting smaller and smaller. However, these applications place higher and higher requirements on the light sensing performance of advanced photodetectors. In the process of shrinking the photosensitive area, it also brings the challenge of accurate measurement of quantum efficiency. Enlitech adopts the spatial light homogenizing technology and follows the ASTM standard “Irradiance Mode” test method, which is proven that it can accurately perform quantum efficiency and other key parameter measurements of advanced photodetectors.
-
product
Photo Gate Logger Sensor
NUL-209
This sensor can be used to study various kinds of motion. With six modes of operation, time, velocity or acceleration can be measured with one or two photo gates and associated timing cards, as well as showing pictorially the status (digital 1 or 0) of the voltage output of the photo gate as timing cards pass through it.
-
product
Mask Testing Instrument(N95,KN95,Disposable Mask)
Sanwood Environmental Chambers Co ., Ltd.
Is used to test the filtration level of aerosol particles by respirator filter element under certain environmental conditions.
-
product
Large Photo Signal Generator
DDS9m
170MHz 4-Channel Signal Generator. The DDS9m generates four independent, phase synchronous sine wave output signals and is programmable in 0.1Hz steps from 0.1Hz to 171MHz. Programming is via an RS232 serial interface. Phase is 14-bit programmable and amplitude is 10-bit programmable. The DDS9m is accurate to 1.5ppm when using the on board TCXO timebase or you can use an external timebase. It requires 3.3 VDC power. SOF8_409 windows software is available as an extra cost accessory.
-
product
Medical Mask Gas Exchange Pressure Difference Tester
DRK371-II
Shandong Drick Instruments Co., Ltd.
It is used to measure the gas exchange pressure difference of medical surgical masks and other products.
-
product
NanoLattice Pitch Standard for Mask Handling Tools (NLSM)
The NanoLattice™ (NLSM) 100 nm pitch standard utilizes gratings with near perfect periodicity to calibrate magnification and scan linearity of CD-SEM and Atomic Force Microscopes (AFM). Make the grade, with the only pitch standard of its kind available below the 130 nm node.
-
product
Mask ventilation resistance and pressure differential tester
WKS-3102
Mask ventilation resistance and pressure differential tester is used to measure the inhalation and exhalation resistance of mask under specified conditions. Applicable to mask manufacturers, labor protection equipment inspection agencies to carry out related testing and inspection of mask products, mask breath resistance tester, breathing valve air tightness tester, breath resistance machine for measuring respirator and mask protection products in Inspiratory resistance and expiratory resistance under specified conditions.
-
product
Medical Masks Flammability Tester
TF361
TESTEX Testing Equipment Systems Ltd.
Medical Masks Flammability Tester is used to test the flammability of medical masks, to ensure the safety of masks to wear in. Medical Masks Flammability test Chamber complies with EN 149, GB 2626, GB 19083.
-
product
DisplayMate Multimedia with Test Photos Edition
DisplayMate Technologies Corporation
DisplayMate Multimedia with Test Photos Edition is an enhanced version of the standard Multimedia Edition that adds a carefully chosen set of very high quality high resolution photographs for calibrating, testing, evaluating, and tweaking monitors, projectors and HDTVs, automatically scaled to the native resolution of the display. It has everything in the standard Multimedia Edition including all of its 500+ test patterns up through 4100 x 4100 resolution.
-
product
Photo Detector with Integrated Transimpedance Amplifiers
ADN3010-11
Analog Devices optoelectronic amplifiers include a range of germanium photodiodes that, through a proprietary process, have been monolithically integrated with silicon transimpedance amplifiers and limiting amplifiers. This process eliminates the need for bond wires connecting the photodiode to the transimpedance amplifier, which leads to improved performance and greater manufacturing reliability. Our portfolio of products also supports the growing need for optical and electrical interface miniaturization.
-
-
product
Masks Particle Filtration Efficiency Tester
Sataton Instruments Technology CO., Ltd
Face masks particle filtration efficiency (BFE) tester is device to determine the particle filter penetration and filtration efficiency for respiratory protective devices and face masks. The tester with particle generator can provide sodium chloride particles and paraffin oil particles. It can measure the particle penetration, filtering efficiency and the breathing resistance delta P. It is widely used in quality control, research and development, certification, manufacturing or testing industry, etc.
-
product
Masks Synthetic Blood Penetration Tester
Sataton Instruments Technology CO., Ltd
Medical face masks synthetic blood penetration resistance tester is to evaluate the penetration – splash resistance property of medical face masks by the impact of a small fixed volume of a high-velocity stream of synthetic blood which is projected horizontally. The pneumatically controlled valve will simulate the splatter of blood or other body fluid to disburse at the specimen mask. The tester is suitable to determine the synthetic blood penetration of materials or certain materials used in medical face masks.
-
product
Mask UV Sterilizers
UV-MASK
Mask UV Sterilizer applies to sterilizing the surface of masks, protective clothing, food, toys and other objects. It is widely used in hospitals, food, tea food and beverage processing and packaging equipment, food factories, cosmetics factories, dairy factories, breweries, beverage factories, bakeries and refrigerators, etc.
-
-
product
Mask Produce and Test Machine
LISUN produce the bfe tester for face mask, pfe tester, melt-blown cloth electrostatic electret generator according to ASTM F1862-17, ASTM F2299-03 (2017), ASTM F2100-2019, BS EN14683-2019, BS EN 14387-2004+A1 2008, BS EN 136-1998, BS EN 140-1999, BS EN 143-2000 +C1-A1, BS EN 149-2001+A1
-
product
Reticle / Mask Particle Detection System
PR-PD2HR
In semiconductor plants, where high performance and demanding functionality are required, the HORIBA PD Series'' high operating rate and long-term dependability have earned it a solid reputation. Inheriting a transfer system that has proven to provide stable, high performance and superior throughput over long operating periods, the PR-PD2HR now offers the most sensitive detection in the series with exclusive signal processing that can detect particles as small as 0.35 m.
-
product
Photo Detectors
Vishay has the broadest portfolio of PIN photobodies on the market. Vishay's photo detectors, photo transistors, and light detectors offer lower capacitance, provide high-speed response, and low noise and low dark current along with excellent sensitivity. They are ideal for high-speed data transfer, light barriers, alarm systems, and linear light measurement.
