Filter Results By:
Products
Applications
Manufacturers
- Virginia Panel Corporation
product
Signal Patchcord, RCV, SIM VTAC, 72", DVI-D Male Single Link, 4 Position
7-142706735
Signal Patchcord, RCV, SIM VTAC, 72", DVI-D Male Single Link, 4 Position
-
product
Area Scan Camera
Area Scan Cameras provide high-performance and high-resolution options that offer excellent image quality and many sensor options. They can connect over a variety of interface standards such as USB3 Vision, GigE Vision, and Camera Link. Models offer high frame rates and rolling or global shutters. Area Scan Cameras are well suited for a variety of applications, such as automated inspection, smart machine control, and factory automation.
-
product
Linescan SWIR Camera
LINECAM12
Princeton Infrared Technologies, Inc.
The LineCam12 is an advanced linescan SWIR camera with 14-bit digital data at 37klines/s on USB3 or Camera Link™ outputs. The SWIR camera currently comes in two varieties: 250 μm tall pixels for spectroscopy and 12.5 μm square pixels for machine vision applications. The camera has incredible versatility enabling full wells from 75ke- to 100Me- with 128 steps of variation as well as integration times from 10 µs to 150s. On chip optical pixel binning (where every other detector is disconnected from the ROIC thus signal is captured by neighboring pixels) is available by command to trade spectral resolution for increased signal level. Pixel skipping or binning is also available allowing for 48k lines/s at 512 resolution in the same camera platform, activated by a simple command structure. The TEC stabilized camera has 31 non-uniformity correction (NUC) tables with 15 factory set and 16 user defined tables to enable flexibility for the given environment.
-
product
Phoenix Camera Link Frame Grabber (D24-PE1)
AS-PHX-D24CL-PE1
Phoenix-D24CL is a PCI Express board for the acquisition of digital data from a variety of Camera Link sources, including digital frame capture and linescan cameras. It supports all the formats of Base configuration, i.e. single 8- to 16-bit data, through 8-bit RGB, to dual tap 12-bit sources.
-
product
Phoenix PMC Camera Link Frame Grabber
AS-PHX-D24CL-PMC32-B
Phoenix-Dig24CL is a PCI board for the acquisition of digital data from a variety of Camera Link sources, including digital frame capture and linescan cameras. It supports all the formats of Base configuration, i.e. single 8- to 16-bit data, through 8-bit RGB, to dual tap 12-bit sources.
-
product
PXIe-1435, Base-, Medium-, Full-Configuration Camera Link PXI Frame Grabber Module
781699-01
Base-, Medium-, Full-Configuration Camera Link PXI Frame Grabber Module—The PXIe‑1435 is a Camera Link image acquisition device designed for machine vision and scientific imaging applications that require high data throughput. The PXIe‑1435 works with any base‑, medium‑, and full‑configuration Camera Link camera, and it is ideal for many industrial, life science, and biomedical imaging applications. The PXIe‑1435 also supports Power over Camera Link (PoCL) and can power cameras through PoCL‑enabled cables. The onboard digital I/O includes four TTL, two optoisolated inputs, and one quadrature encoder.
-
product
Base/PoCL Camera Link frame grabber
Neon-CLB
Simplify your industrial, medical, or semiconductor imaging application with BitFlow's Neon-CLB, the easiest to use and most reliable Base/PoCL Camera Link frame grabber available anywhere. The Neon-CLB captures images at up to the camera's highest frame/data rate, with precision image acquisition suitable for the most demanding applications.
-
product
PXIe-1487, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO GMSL™ Interface Module
787457-01
The PXIe-1487 combines the Maxim Integrated Gigabit Multimedia Serial Link™ (GMSL™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1487 makes use of a combination of GMSL™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable GMSL™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the GMSL™ channels. The PXIe-1487 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). GMSL is a trademark of Maxim Integrated Products, Inc.
-
product
Software
Active Silicon computer vision products are supported by a variety of software tools. We provide powerful user software and SDKs for CoaXPress and Camera Link frame grabbers with support across several operating systems. Additionally, a wide range of drivers for third-party machine vision and scientific imaging packages is available.
-
product
Xtium2 Frame Grabber Family
The Xtium2 series leverages the PCIe Gen3 x8 platform to deliver high- speed image transfers to host memory without CPU overhead. Featuring Camera Link HS® interface standards, supports Active Optic Cable and SFP+ modules, CoaXpress® 12, and Camera Link®.
-
product
FastCamera
FC300
The FastCamera 300 is a high-speed 3 megapixel digital camera system, using a CMOS imager with an electronic global shutter. This camera has a the option of a high-speed, scalable, integrated FPGA, image processor, and memory subsystem which enables stand-alone high speed in camera image processing and extended storage. Options include back thinned versions with high QE in the visible and NIR range, ruggedized, Camera Link output. When integrated with a high powered frame grabber /coprocessor board, the resulting system capabilities can be expanded by adding processors and memory on the board according to the needs of the user.
-
product
FireBird Camera Link Frame Grabber (1xCLD-2PE4)
AS-FBD-1XCLD-2PE4
FireBird is designed for ultimate performance using Active Silicon’s proprietary DMA Engine technology, “ActiveDMA”. This technical innovation applies RISC based processor techniques and guarantees zero CPU intervention, high-speed and low-latency image data transfers.
-
product
FastCamera
FC200
The FastCamera 200 is a high-speed 2 megapixel digital camera system, using a CMOS imager with an electronic global shutter. This camera has a the option of a high-speed, scalable, integrated FPGA, image processor, and memory subsystem which enables stand-alone high speed in camera image processing and extended storage. Options include back thinned versions with high QE in the visible and NIR range, ruggedized, Camera Link output. When integrated with a high powered frame grabber /coprocessor board, the resulting system capabilities can be expanded by adding processors and memory on the board according to the needs of the user.
-
product
Dual Camera Link LPC FMC
FMC-CL
Sundance Multiprocessor Technology Ltd.
The FMC-CL is a dual port camera link LPC FMC card.
-
product
Xcelera Frame Grabber Family
The Xcelera Series leverages the PCI Express (PCIe) platform to bring traditional image acquisition and processing technology to new levels of performance and flexibility. This unified and scalable platform currently supports high-performance Camera Link™ cameras.
-
product
FireBird Camera Link 3U cPCI Serial Frame Grabber
AS-FBD-1XCLD-3CPCIS-2PE4
The FireBird Camera Link CompactPCI Serial card is a member of Active Silicon’s state-of-the-art FireBird frame grabber family. FireBird is designed for ultimate performance using Active Silicon’s proprietary DMA Engine technology, “ActiveDMA”. This technical innovation applies RISC based processor techniques and guarantees zero CPU intervention, high-speed and low-latency image data transfers.
-
product
Virtex-5 XMC/PMC
XMC-FPGA05D
Curtiss-Wright Defense Solutions
The XMC-FPGA05D high density I/O module controlled by a user programmable Xilinx Virtex-5 FPGA and supported by a range of front panel I/O modules including analog I/O, RS-485/422, LVDS and Camera Link.
-
product
Phoenix 3U cPCI Camera Link Frame Grabber
AS-PHX-D48CL-3CPCI32-B-CR
Phoenix-D48CL is a 3U CompactPCI board for the acquisition of digital data from a variety of Camera Link sources, including digital frame capture and linescan cameras. It supports all the formats of the Base and Medium configurations, i.e. single 8- to 16-bit data, through 12-bit RGB, to four tap 12-bit sources, as well as dual Base configuration, i.e. acquisition from two asynchronous Base cameras.
-
product
PCIe-1437, 80-Bit Camera Link, PoCL-Compatible Frame Grabber Device
785605-01
The PCIe-1437 is a Camera Link image acquisition device designed for machine vision and scientific imaging applications that require high data throughput. The PCIe-1437 includes an onboard FIFO for higher bandwidth use cases, and it works with any base‑, medium-, and full-configuration Camera Link camera. The PCIe-1437 is ideal for many industrial, life science, and biomedical imaging applications. The PCIe-1437 also supports Power over Camera Link (PoCL) and can power cameras through PoCL-enabled cables.
-
product
Area Scan Camera
Genie Nano-5GigE
Engineered for imaging applications that require high-speed data transfer, the all new Genie Nano 5GigE is an easy replacement for gigabit ethernet cameras built into current vision systems that rely on the existing GigE Vision interface standard. The new Genie Nano 5GigE models feature the brand new 5Gbps (5GBASE-T) link speed.
-
product
Xtium Frame Grabber Family
The Xtium series delivers higher bandwidth to sustain Camera Link 80-Bit modes over longer cable distances and supports a wide variety of area and line scan color and monochrome cameras, all in a compact, single slot solution.
-
product
Camera Link Adapter Module For FlexRIO
The Camera Link Adapter Module for FlexRIO supports 80‐bit, 10‐tap base‐, medium‐, and full‐configuration image acquisition from Camera Link 1.2 standard cameras. You can pair the Camera Link Adapter Module for FlexRIO with a PXI FPGA Module for FlexRIO for applications that require bit‐level processing and very low system latency. With the Camera Link Adapter Module for FlexRIO, you can use the FPGA to process images from the camera in-line before sending the images to the CPU, enabling more advanced preprocessing architectures.
-
product
Phoenix PC/104-Plus Camera Link Frame Grabber
AS-PHX-D24CL-PC104P32
Phoenix-D24CL PC/104-Plus is a PCI board for the acquisition of digital data from a variety of Camera Link sources, including digital frame capture and linescan cameras. It supports all the formats of Base configuration, i.e. single 8- to 16-bit data, through 8-bit RGB, to dual tap 12-bit sources.
-
product
CL PX4 SE Frame Grabber
Xcelera-CL PX4 SE
The X64 Xcelera-CL PX4 SE is a highly versatile PCIe frame grabber capable for one Camera Link™ Base, Medium, or Full camera and performing image transfers at rates up to 1024MB/s. Its low cost, combined with its ability to support multiple tap configurations from area and linescan monochrome/RGB cameras simultaneously; in addition to its onboard FPGA Bayer decoding and real-time shading correction makes the X64 Xcelera-CL PX4 SE an ideal solution to a wide variety of cost-sensitive applications.
-
product
Phoenix Camera Link Frame Grabber (D48-PE4H)
AS-PHX-D48CL-PE4H
Phoenix-D48CL x4is a PCI Express board for the acquisition of digital data from a variety of Camera Link sources, including digital frame capture and linescan cameras. It supports all the formats of the Base and Medium configurations, i.e. single 8- to 16-bit data, through 12-bit RGB, to four tap 12-bit sources, as well as dual Base configuration, i.e. acquisition from two asynchronous Base cameras.
-
product
FastCamera
FC1700
The FastCamera FC1700 is a high-speed 17 megapixel digital camera system, using a CMOS imager with an electronic global shutter, or rolling shutter. This camera has a high-speed, scalable, integrated FPGA, image processor, and memory subsystem which enables stand-alone high speed in camera image processing and extended storage. Options include ruggedized, Expanded Camera Link output, Gigabit Ethernet output, and in camera recording. When integrated with a high powered frame grabber /coprocessor board, the resulting system capabilities can be expanded by adding processors and memory on the board according to the needs of the user.
-
product
Accessories & Cables
Active Silicon offer a range of accessories for our hardware products, including CoaXPress and Camera Link cables and FireBird IO adapters for use with our frame grabbers. The products listed on our website are in stock and readily available. Other cable lengths or adapter types, are available on request, especially for higher order volumes.
-
product
Camera Link Simulator
CLS-221
The CLS-221 Camera Link Simulator is an affordable, high-performance video test pattern generator that supports all video formats including those introduced in the new version 2.1 specification. Fully programmable video timing enables the CLS-221 to mimic the characteristics of almost any camera. New features include enhanced timing performance, bayer color support, and additional video patterns. Control is via an RS-232 port, USB, or frame grabber COM port. The CLS-221 also incorporates the AIA validation test pattern.
-
product
Camera Link Frame grabber
Cyton-CXP
CoaXPress (CXP) is a simple, yet powerful, standard for moving high speed serial data from a camera to a frame grabber. Video is captured at speeds of up to 6.25 Gigabits/Second (Gb/S). Simultaneously, control commands and triggers can be sent to the camera 20 Mb/S (with a trigger accuracy of +/- 2 nanoseconds). Up to 13 W of power can also supplied to the camera.
-
product
PXIe-1487, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO GMSL™ Interface Module
787458-01
The PXIe-1487 combines the Maxim Integrated Gigabit Multimedia Serial Link™ (GMSL™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1487 makes use of a combination of GMSL™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable GMSL™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the GMSL™ channels. The PXIe-1487 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). GMSL is a trademark of Maxim Integrated Products, Inc.
-
product
Frame Grabbers
* Supporting most performance-demanding Machine Vision protocols, such as CoaXPress, Camera Link HS, 10 GigE, Fiber etc.* Ideally suited for industrial, defense and aerospace Machine Vision Systems.* These products are complimented by sophisticated application software package and SDK, for Windows and Linux OS’s.
