Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PCI Simulation Modules For Sensor Simulation
Does your test strategy require simulating environmental sensors, including temperature, pressure, altitude, and strain gauges.
-
product
Test Engines
Verified Systems International GMBH
The test system cluster architecture is based on dual CPU or 4-CPU PCs acting as cluster nodes. The nodes communicate and synchronise over a high-speed network (Myrinet or InfiniBand). A modification of the Linux operating system allows to run the test execution and evaluation algorithms in hard real-time on reserved CPUs, where scheduling is non-preemptive and controlled by the test system itself. The interrupts caused by interfaces to the system under test may be relayed to CPUs designated explicitly for their handling. This approach offers the opportunity to utilise high-performance standard hardware and the services provided by the widely accepted Linux operating system in combination with all mechanisms required for hard real-time computing. The cluster architecture presents an opportunity to distribute interfaces with high data throughput on different nodes, so that PCI bus overload can be avoided. In addition, the CPU load can be balanced by allocating test data generators, environment simulations and checkers for the behaviour of the system under test ("test oracles") on dedicated CPUs.
-
product
Panel-mounted Power Amplifier
PAC2000B
PA series amplifiers are specially designed for power network real time simulation applications,which requires large power output,high accuracy even at high current output for all kinds of load.
-
product
Vehicle Communication Buses
Vehicle Communication Buses provide native support for Controller Area Network (CAN), Local Interconnect Network (LIN), and FlexRay frames and signals. Use these products for hardware-in-the-loop simulation, bus monitoring, automation control, and more.
-
product
Network Analysis
Network analysis includes a powerful set of analytical tools that allow for simulation, prediction, design and planning of system behavior utilizing an intelligent one-line diagram and the flexibility of a multi-dimensional database.
-
product
Comprehensive Simulation of Master, Slave and End Nodes in A 2 B ® Networks
Infotainment Test Device ITD 1024
The complexity, cost and weight of audio systems are significantly reduced with the Automotive Audio Bus (A 2 B ® ) from Analog Devices Inc. Regardless of their hierarchical structure or use as master or slave, all A 2 B ® products must be adequately tested before use. This applies, for example, to HiFi amplifiers/loudspeakers, head units, eCall systems, microphones, vibration/noise suppression units, actuators or sensors.Our small and very compact infotainment test system ITD 1024 takes on this task for you: It comprehensively and extremely reliably tests all A 2 B ® signals and communication in all phases of the product development process - during development, for validation and in production.
-
product
XDSL Testers
GAOTek offers a wide range of xDSL testers that are specifically manufactured to meet the requirement of xDSL testing, along with ADSL, ADSL2, ADSL2+, READSL, and VDSL for sale to the United States, Canada and Globally. They are mainly used by field operators for telecommunication installation, troubleshooting of xDSL network and maintenance. xDSL testers not only tests the physical structure but also evaluates whether the line is fit for xDSL service and consider the quality of service. The devices can be operated in “ATUR+PC” simulation without any external ADSL2+/VDSL2 modem or computer as they can be easily operated by digital multi-meter. These devices evaluate line quality, carry out PPPoE dial-up, suggest web page browsing to determine the connection to the ISP, and emulates a PC+ modem. These testing devices also help with PING, IP config, route and tracert tests. Moreover, these devices can also function as a computer for examining broadband IP lines or begin a PPPoE dial-up to determine IP network connection and troubleshooting a computer or modem issues.
-
product
NI-9861, 1-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module
781962-01
1-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module—The NI‑9861 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The NI‑9861 is ideal for applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other data acquisition measurements in the same NI CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same NI CompactRIO chassis.
-
product
Automotive Audio Bus (A²B) Analyzer System
A simulation and analysis solution for automotive audio networks based on the emerging Automotive Audio Bus® standard. The A2B Analyzer System is designed specifically for development teams servicing automotive OEMs, Tier 1s, and audio connectivity equipment suppliers. The deterministic nature of the A2B technology makes it particularly well-suited for automotive audio devices (active speakers, microphones) and newer applications such as Active Noise Cancellation (ANC), In-car Communications, etc.
-
product
PXI-8513, 1‑Port, Software-Selectable PXI CAN Interface Module
780688-01
1‑Port, Software-Selectable PXI CAN Interface Module—The PXI‑8513 is a software-selectable Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. NI‑XNET Software‑Selectable CAN Interfaces offer the best flexibility for CAN development with onboard transceivers for High-Speed/Flexible Data‑rate, Low-Speed/Fault Tolerant Single Wire CAN as well as any external transceiver. The PXI‑8513 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
product
Precise Testing & Simulation of A2B® Networks
A2B®-Component-Tester
The Automotive Audio Bus (A²B®) is a bus developed by Analog Devices Inc. for infotainment systems in automobiles. It is increasingly being used in other applications such as AV conferencing systems. Typical A²B® -products are Hi-Fi amplifiers/speakers, head units, eCall systems, microphones, vibration/noise suppression units, actuators, or sensorsCommunication happens via a simple two-wire UTP (Unshielded Twist Pair) cable. All A²B® -components are connected in a master/slave architecture to form a network. The complexity of audio systems in these A²B® -networks is reduced, and with it the cost and weight.
-
product
AINC 429 Multichannel Interface with Additional ARINC-717 Receive & Transmit Channels
DAS-429UNET/RT8-717
The DAS-429UNET/RT8-717 is an ARINC 429, multichannel interface card with additional ARINC-717 receive and transmit channels. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the ARINC 429 & ARINC-717 bus, both in the lab and in the field.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.The EXC-429UNET/RT8-717 adapter is supplied with C drivers, including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application (only versions 8.1 or higher).
-
product
CAN, CANopen, J1939 Tester
X-Analyser3
Warwick Control Technologies Ltd.
Graphical User Interface ideal for Windows PCs and tablets.• CAN, J1939, NMEA2000, CANopen, LIN and OBD – included into one tool• On-Board Diagnostics Scan Tool Features for Emissions ECUs.• CAN and LIN signal reverse engineering• Signals displays – text, scope and graphical such as gauges and lamps• Can be used for ECU or even network simulation• SAE J1939 database integrated with over 4000 PGNs and signals
-
product
Vector Network Analyzer
SNA5000A
The SIGLENT SNA5000A series of Vector Network Analyzers have a frequency range of 9 kHz to 8.5 GHz, with 2 and 4 port models available. Designed to give you instant insight into scattering, differential, and time-domain measurements. They are effective instrumentation for determining the Q-factor, bandwidth, and insertion loss filters and feature impedance conversion, movement of measurement plane, limit testing, ripple test, fixture simulation, and adapter removal/insertion adjustments. There are five sweep types: Linear-Frequency, Log-Frequency, Power-Sweep, CW-Time, and Segment-Sweep mode. The SNA5000A series VNAs also support scattering-parameter correction of SOLT, SOLR, TRL, Response, and Enhanced Response for increased flexibility in R&D and manufacturing applications.
-
product
PCI-8512, 2-Port, High‑Speed/FD CAN Interface Device
780683-02
The PCI‑8512 is a high-speed controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. The PCI‑8512 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
product
sbRIO-9866, Non-Enclosed, 1-Port C Series LIN Interface Module
785965-01
Non-Enclosed, 1-Port C Series LIN Interface Module—The sbRIO‑9866 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The sbRIO‑9866 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals such as hardware‑in‑the‑loop (HIL) simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other DAQ measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO Chassis. Non-enclosed modules are designed for OEM applications.
-
product
Line Monitor
LE-170SA
LE-170SA is a compact hand-held size line monitor for CAN/LIN. It has a touch screen and can be control as for smartfones. It has 1 CAN channel and 1 LIN channel and it can monitor both CAN and LIN communication thus monitoring of the network which has both CAN and LIN is available. The monitor function can diplay the communication data in real-time while saving it. The simulation function can send/receive the test data instead of the original communication partner. The ID filtering and trigger function make your development/evaluation more efficient. It also can measure 4 external signals as degital signals or analog signals while monitoring the communication data.It is light (300g) and convenient for field testing. The line monitor is useful for not only development but also maintenance.
-
product
BusTools/1553 BusTools Software Analyzer
Abaco Systems' BusTools-1553 is an integrated, Microsoft Windows-based, application solution for MIL-STD-1553 test, analysis and simulation. BT-1553 software harnesses the power of Abaco Systems' hardware interfaces on PCI, PCI Express, CompactPCI, PMC, ExpressCard, PCMCIA, USB, XMC, PC/104-Plus, VME and VXI platforms for simplified control over simulation, display, data logging, playback, and protocol analysis of MIL-STD-1553/1760 A and B networks.
-
product
High Speed Optical Avionics Network Test Instrument
PXIe-25G
Avionics Interface Technologies
PXI Express Instrument for test and simulation of Fibre Channel and Avionics Ethernet (10G and 25G). Instrument provides 4 optical network interfaces and is software configurable to provide 4 ports of Ethernet, 4 ports of Fibre Channel, or 2 ports of each.
-
product
Network Testing Tools
Network IP traffic packet generators are used for network performance testing under maximum or partial throughput conditions. Network health can be analyzed by network traffic measurement in a testbed network, using an IP network traffic generator such as IP Traffic Test and Measure. The traffic generator sends packets, often with a unique packet identifier, making it possible to keep track of the packet delivery in the network.Network impairment simulation (emulation) is a technique for testing the performance of real applications over a virtual network. The aim is to assess performance, predict the impact of change, analyze impairment conditions or otherwise optimize technology decision-making. Measurements usually focus on simulation of conditions like delay, jitter, latency, dropped packets and limited bandwidth.
-
product
BusTools Software Analyzer
AFDX-A
BusTools/AFDX-A is a Windows 7/10-based GUI application solution from Abaco Systems that establishes new levels of power, flexibility and ease-of-use for AFDX (Avionics Full Duplex Switched Ethernet) traffic monitoring, analysis and simulation. Available for use with our powerful CNIC interface, BusTools/AFDX offers an intuitive interface to view, log, analyze and generate AFDX network traffic at the Adapter, End System, Virtual Link (VL) and Port levels. Contact Goleta factory for listing of supported products.
-
product
Rugged Ethernet
ES-1553RUNET/Px(S)
The ES-1553RUNET/Px is an intelligent, rugged single channel, MIL-STD-1553 adapter. Its small size and ability to interface through Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the MIL-STD-1553 bus, both in the lab and in rugged environments.The ES-1553RUNET/Px shares its API with the entire Px family so that applications currently running on PCI, PCIe, ExCARD or PCMCIA boards will run without change on this device.Multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.
-
product
PCI Switch & Simulation Cards
Instrumentation grade PCI switch and simulation cards can be cascaded to form more extensive switching networks.
-
product
ARINC818 Cards
> ARINC818 is a specification which has become an Industry standard for the transmission of uncompressed digital video. This commercial standard uses Fibre Channel as a point-to-point communication link for low latency with the ARINC818 defining the packetized protocol for transmission of the digital video information. It is highly flexible and can be used for a variety of onboard display systems in both commercial and military applications. AIM’s ARINC818 cards use our field proven Common Core hardware design giving the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with one dual core RISC processor per port, massive DDR3 memory and IRIG-B time encoder/decoder functions are standard. The ARINC818 modules are available in PCIe formats.The new ultra high performance intelligent 4-lane PCIe 2.0 interface modules offer 2 ports with full function test, simulation, monitoring and analyzer functions for ARINC818 interfaces. The dual core processor provides onboard processing and data transfer capabilities for the most demanding applications including ARINC818 support done on board level. Large and high data throughput DDR3 RAM is accessible for the onboard processor as is a high performance FPGA implementing the customized ARINC818 Interfaces enabling the board to analyze incoming data in real time. Each module provides 2 ARINC818 compliant ports. SFP cages make it suitable for different media types as optical or electrical network technologies. Each module is delivered with a Board Support Package (BSP) containing the onboard driver software, a full Application Programming Interface (API) and detailed getting started and programming guides. Powerful PBA.pro databus test and analysis software is optionally available for all our ARINC818 cards.
-
product
TDL Network Simulation
Curtiss-Wright Defense Solutions
The need for realistic and effective military training simulations is fundamental to prepare warfighters for the challenges they may face on the field. The TCG portfolio of advanced tactical data link solutions enables the creation of configurable high-fidelity simulations, both real-time or scripted, of the industry’s most prominent data link protocols and standards.
-
product
Communication Network Lab (5G, 4G, 3G, 2G, IP, TDM)
GL’s End-to-End Wireless Network Simulation Test Suite provides you an advanced full-fledged “Live Network” at your company premises in any customized package to suit test requirements.
-
product
Network Simulation and Load Testing
EXFO offers a complete range of high-performance test solutions, covering the entire converged network from RAN to IMS. By mimicking real-world customer behavior in lab environments, our solutions allow mobile operators and equipment manufacturers to verify their wireless networks before deployment.
-
product
Avionics Network Simulation Systems
Avionics Interface Technologies
Support for up to 30 Network Interfaces (Fibre Channel & Ethernet)Time Synchronization with IRIG-B & IEEE 1588 Master ClocksFull Data Capture with time stampingData simulation with precise timing & synchronizationNetwork data replay from previously captured trafficPerform Network analysis using AIT's intuitive, easy to use, Ethernet & Fibre Channel simulation tools
-
product
TesT Software
61850
Simulate, monitor and test IEDs on your digital substation network with Doble's 61850 TesT Software.Use with Doble's F6150sv and Protection Suite software to apply sampled values (SV) and generic substation event (GSE) simulations to functionally test, receive status messages and get more data from substation devices.
-
product
Fibre Channel Modules
AIM’s Fibre Channel test, simulation and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with one dual core RISC processor per port, massive and scalable DDR3 memory and IRIG-B time encoder/decoder functions are standard. The new ultra high performance intelligent 4-lane PCIe 2.0 interface modules offer 2 ports with full function test, simulation, monitoring and analyzer functions for Fibre Channel networks. The dual core processor provides onboard processing and data transfer capabilities for the most demanding Fibre Channel applications including upper layer protocol support done on board level. Large and high data throughput DDR3 RAM is accessible for the onboard processor as is a high performance FPGA implementing the customized Fibre Channel interfaces enabling the board to analyze incoming and modify outgoing data in real time. Each module provides 2 Fibre Channel compliant full duplex ports, implementing the full link level services. SFP cages make it suitable for different media types as optical or electrical network technologies. Ports operate either in Traffic Simulator or Analyzer/Monitor mode with support for port related Frame Statistics. Sophisticated packet capturing mechanism and monitoring features are complimented with powerful triggering and filtering capabilities.
-
product
Avionics Test & Simulation Interfaces
Connect your PC laptop, desktop and tablet computers to avionics databuses with pocket-sized Ballard USB interfaces. Ease of use, versatility and comprehensive databus functionality have made these rugged adapters the industry favorite for avionics test, analysis and simulation in the lab and in the field. Avionics labs routinely integrate Ballard interface cards and full-featured network appliances into their test setups for powerful and reliable databus connection.
