Filter Results By:
Products
Applications
Manufacturers
Absorbers
dampen wave reflection.
- Taylor Dynamometer, Inc.
product
Towing Dynamometer
RS-125K
RS-125K towing dynamometer is designed for testing Class A trucks and is the most full-featured, reliable and accurate towing dynamometer in the industry. The RS-125K is built with a heavy-duty steel frame, heavy-duty industrial axles and rides on an air ride suspension. The RS-125K is designed to maintain 125,000 Newtons of constant drawbar pull and the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there are no lead-acid batteries to charge and testing is unlimited at low speeds
-
product
Heavy Duty Dynamometers
MD-250-HD
The MD-250-HD series dyno (SE/DE) was designed to be a performance dynamometer first with the added benefit of being able to test 2-wheel-drive heavy-duty vehicles such as truck, buses and commercial vehicles in addition to the standard car or light duty pick-up. The 250-HD is certified in the states of Colorado, Nevada and Utah for use in loaded-mode diesel smog testing programs because of its accuracy and reliability. No other dyno in its class offers more value or better in-house motor vehicle testing capabilities than the Mustang MD-250-HD. For starters, the MD-250-HD boasts a 1,500 horsepower measurement capacity at a top speed of 175 mph and a powerful air-cooled eddy current brake provides the MD-250-HD-SE with 900-hp worth ofloading capacity for steady state testing. Loading capacity can be increased to 1,500-hp via the optional DE model. The 250-HD can be upgraded to the 250-HD-SE-M via the addition of a 100 or 200 hp AC motor for transient testing of electric buses to measure range and regeneration or for emissions testing of IC engines. Do not be fooled by its compact size – the MD-250-HD is a serious dynamometer with serious tuning capabilities. The MD-250-HD uses a powerful eddy current power absorber, a frictionless, air-cooled braking device, to enable it to apply variable and steady state loading. A complete control and data acquisition system lets you design a wide range of tests or select from a host of pre-configured tests included with the standard system. The 250-HD’s four roller design makes setting up vehicles a snap – simply drive onto the 250-HD and let the tires settle in between the rollers. The 250-HD can be installed above-ground or below-ground, it’s your choice. The above-ground system utilizes an optional premium platform and ramp system with an above-ground restraint kit. The addition of an axle pull-down kit help keep the tires from slipping or trying to “climb out” of the rollers.
-
product
Towing Dynamometer
RS-8K
Taylor Dynamometer’s RS-8K Towing Dynamometer is designed for testing today’s mid-sized cars and SUVs. The RS-8K is built with an all aluminum frame, an aerodynamic body and rides on an independent, air ride suspension and uses an eddy current absorber with special high temperature coils to absorb energy. The RS-8K is powered by an industrial generator, so unlike battery/alternator Towing Dynamometers, there are no lead-acid batteries to charge and testing time is unlimited at low speeds.
-
product
Air Core Shunt Reactors
Shunt Reactors act as absorbers of reactive power to increase energy efficiency of the power system. Shunt Reactors are inductors that are used in order to compensate capacitive reactive power generated by long and lightly loaded transmission lines as well as underground cables, thus allowing the flow of more active power through the system and avoiding over voltages. The shunt reactors provide inductive compensation.
-
product
Structural Durability Solutions
Instron offers a variety of testing systems and rigs for static, quasi-static and dynamic loading of structures and components. This includes Component Test Systems, Shaking Tables, Road Simulators, Axle Test Systems, Full Vehicle Test Systems, Wheel Test Systems, Shock Absorber Test Systems, Elastomer Test System and Dynamic Torsion Test Systems.
-
product
Towing Dynamometer
RS-110K
RS-110K towing dynamometer is designed for testing Class A trucks and is the most full-featured, reliable and accurate towing dynamometer in the industry. The RS-110K is built with a heavy-duty steel frame, heavy-duty industrial axles and rides on an air ride suspension. The RS-110K is designed to maintain 110,000 Newtons of constant drawbar pull and the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there are no lead-acid batteries to charge and testing is unlimited at low speeds.
-
product
RF Shielded Enclosure for Pre-Compliance EMC and CTIA Testing
QuietBox-AR "Mini-Range"
The Raymond RF QuietBox-AR is a mobile solution for pre-compliance EMC and CTIA testing, 3D antenna pattern measurement, and total radiated power & total isotropic sensitivity testing. Fully equipped with client-specified broadband absorber, integrated antenna and rolling cart, the QuietBox-AR is a cost effective option for product verification prior to fully compliant testing.
-
product
Towing Dynamometer
RSL-5.4K
RSL-5.4K Towing Dynamometer is designed for testing today’s compact cars. The RSL-5.4K is built with an all aluminum frame, sheet metal body and rides on an independent, coil spring suspension. The RSL 5.4K uses an eddy current absorber for power absorption. The power is provided by batteries and an alternator.
-
product
Towing Dynamometer
RSL-8K
RSL-8K Towing Dynamometer is designed for testing today’s mid-sized cars and compact SUVs. The RSL-8K is built with an all-aluminum frame, sheet metal body and rides on an independent, coil spring suspension. The RSL-8K uses an eddy current absorber for power absorption. The power is provided by batteries and an alternator.
-
product
Antenna Testing Services
Our chamber measures 28' x 14' x 14' with 12" to 36" pyramidal anechoic absorbers and is fully shielded using a dual layer metal enclosure. Our test chamber is designed to for frequencies ranging from .700 to 6.00 GHz.
-
product
Diesel Dynamometers
Heavy-duty toroidal water-brake or large eddy-current absorber, S-beam electronic torque transducer, high-flow manual (or optional electronic) engine load control, DYNOmite data-acquisition computer, rigid-frame engine test stand, wall (or stand) mounted control console, absorber to engine-block mounting adapter, heavy-duty input shaft, calibration arm, stainless-braided hoses, and full-function data wiring harness.
-
product
GTEM cells
Meets IEC/EN 61000-4-20, SAE J1752/3, IEC 62132-2 and IEC 61967-2. The GTEM cell is, in principle, a tapered coaxial line (offset septum plate), which is terminated by a hybrid combination of discrete resistors and RF absorbers to achieve a 50 Ohm broadband match. It is applied for Measuring of Emission, Radiated, radio frequency field-immunity test.
-
product
High Power Thermal Sensors & Power Pucks – 1W to 120kW
15K-W-BB-45
The 15K-W-BB-45 is a water cooled thermal power/energy laser measurement sensor for very high powers with a 45mm aperture. It can measure power from 100W to 15,000W. It has a deflecting cone and annular absorber that withstands high power densities to 10kW/cm². It covers the spectral range from 0.8 - 2 and 10.6µm. The sensor comes with a standard 5 meter cable for connecting to a meter or PC interface.
-
product
High Frequency Retrofits and Relocations
Our services also include upgrades of existing HF chambers to meet new program requirements, absorber installations, and relocations of chambers from one site to another.
-
product
Industrial Shock Absorbers
ACE industrial shock absorbers work hard. Their application means moving loads are evenly decelerated over the full stroke. The result: the lowest braking force and shortest braking time. The MAGNUM series from ACE is viewed as the reference standard for medium-sized damping technology.
-
product
Antenna Test Chamber
Comtest provides Antenna test ranges fully covered with microwave absorbers for both near-field and far-field measurements. Because we always strive for new solutions, our R&D department developed our ‘Javelin Tip’ polystyrene absorbers. The enhanced material composition and altered shape, lead to improved performance and cleaner working space, enabling you to make high precision antenna testing fast, reliable, and worry-free.
-
product
EMC Test & Measurement Solutions
MVG provides anechoic chambers and absorbing materials for antenna and EMC measurement and testing as well as RF and EMP shielding. Our SmartShieldTM modular shielding and precision cut and coated absorbers are designed with the flexibility to meet specific customer requirements. Our knowledge gained from over 30 years of experience ensures the high quality and durability of our products and the expertise from our team.
-
product
Heavy Duty Dynamometers
MD-7500-HD
Today’s Fleet Managers are faced with many challenges – most important of which is maintaining a healthy bottom line. With fuel costs at an all-time high, these challenges have become increasing difficult. Fleets being transitioned from fossil fuels to electric propulsion also face challenges with durability and range to make sure routes can be completed on time each and every day. To help combat these problems and others facing fleet managers today, Mustang Dynamometer offers the MD-7500-HD Series Chassis Dynamometer – which features the most advanced diagnostic capabilities in the industry. The MD-7500-HD is designed to simulate the driving conditions that fleet vehicles encounter on the road every day in a safe and controlled shop floor environment so that critical engine and drivetrain systems can be evaluated to insure vehicles are performing properly and at maximum efficiency. What’s more, the MD-7500-HD offers several levels of testing capabilities in a modular, compact package and with capabilities that can be upgraded in the future as your needs change. Every vehicle in your fleet can now be tested and validated before and after a repair to ensure proper diagnosis and repairs have been performed. In addition to testing repaired vehicles, the MD-7500-HD can be used to test vehicles on a regular basis as a preventative maintenance measure which decreases unexpected breakdowns and allows fleet management to control fuel costs while reducing repair costs. Periodic testing keeps fuel consumption to a minimum and helps technicians identify suspect components before they fail. A proactive approach to Fleet Service can prevent unexpected engine and or drive-train failure which saves organizations thousands of dollars in lost fair revenues. At the heart of the MD-7500-HD is a set of three air-cooled eddy current power absorbers. Each absorber, or brake, can hold up to 600-hp (total power of 1,800-hp) – more than enough to simulate a fully loaded transit bus. As the systems PAU’s (brakes) are air-cooled, no water is required to or from the device – eliminating the high cost of water consumption and/or the cost of an expensive water recovery system – which can sometimes exceed the cost of the dynamometer system itself. Mustang is the only company that offers a Universal Fleet Test Bed without water supply requirements. AC Motors can be added to simulate regeneration and validate range for organizations that have transitioned to carbon free electric propulsion. The 7500 is the best solution for fleet managers looking to improve their bottom line and offer disruption-free public transportation.
-
product
Spring Fatigue Testing Machine
TPJ Series
Jinan Testing Equipment IE Corporation
Model TPJ Series Mechanical Computer Control Spring Fatigue Testing Machine is mainly used for the fatigue properties of all kinds of coil springs, disc springs, shock absorbers, and seal springs etc. The Spring Fatigue Testing Machine consists of motor, reducer on the connecting cams to drive the connecting rod and make reciprocating motion achieve the compression fatigue movement. The Spring Fatigue Testing Machine is efficient without any pollution to the environment. Equipped with different accessories, the Spring Fatigue Testing Machine can test springs of different sizes. Adopting the single-chip machine control, the Spring Fatigue Testing Machine realizes auto stop function when it reaches the preset test times. The Spring Fatigue Testing System is widely used in quality controls for spring, shock absorber production, and relevant applications.
-
product
Medium Voltage Iron Core Oil-Immersed Shunt Reactor
Iron core Oil-immersed Shunt Reactors act as an absorber of reactive power to increase energy efficiency of the power system.
-
product
Towing Dynamometer
RS-10K
RS-10K Towing Dynamometer is designed for testing today’s mid-sized cars and SUVs. The RS-10K is built with an all aluminum frame, an aerodynamic body and rides on an independent, air ride suspension and uses an eddy current absorber with special high temperature coils to absorb energy. The RS-8K is powered by an industrial generator, so unlike battery/alternator Towing Dynamometers, there are no lead-acid batteries to charge and testing time is unlimited at low speeds.
-
product
Large-Displacement Low-Frequence Vibration System
9363-LN-100
King Design Industrial Co., Ltd.
This tester is designed to assess the damage made to product packaging and internal objects caused from transporting environment; to discover the packaging flaw and product’s early failure from a long-term cumulative vibration fatigue; avoid man-made transporting damage and improve product’s reliability and quality of delivered products. With the use of high-performance foot absorber, the resonance effect to floor caused by the bounce test may be waived; and can reduce the pile’s destruction to industrial plants. Two displays can make comparative display on both frequency and rpm at the same time; thus no need to switch in order to read these two values. The dual-control mode of time accumulator and counter can avoid human error resulting from the conversion. Easy to operate; no need for complicate training program.
-
product
Net Radiation Measurement
NR Lite2
The design of the NR Lite2 is unique. The detector is based on a Teflon coated, weather resistant black conical absorber. In contrast to other sensor designs, NR Lite2 requires no fragile plastic domes. This results in a virtually maintenance free design. The vertical stick prevents birds from affecting the output signal.
-
product
Towing Dynamometer
RS-25K
RS-25K Towing Dynamometer is designed for testing today’s full-sized SUVs and light trucks. The RS-25K is built with a heavy-duty steel frame, an aerodynamic body and rides on an independent, air ride suspension using two eddy current absorbers with special high temperature coils to absorb energy. The RS-25K is powered by an industrial generator so there are no lead-acid batteries to charge and testing time is unlimited at low speeds.
-
product
Diesel Fleet Maintenance Chassis Dynamometer
MD-7500
At the heart of the MD-7500 is a set of three air-cooled eddy current power absorbers. Each absorber, or brake, can hold up to 600-hp (total power of 1,800-hp) more than enough to simulate a fully loaded transit bus. As the systems PAU''s (brakes) are air-cooled, no water is required to or from the device eliminating the high cost of water consumption and/or the cost of an expensive water recovery system which can sometimes exceed the cost of the dynamometer system itself. Mustang is the only company that offers a Universal Fleet Test Bed without water supply requirements.
-
product
Mini Compact EMC Test Chamber
EMC-MC
Very useful where space is restricted, the EMC-MC will settle into almost any office space. Its small overall size results from the use of our modular SmartShield chamber lined with our AEPH HyPyr-LossTM absorber technology requiring less volumetric space than in a traditional chamber. This mini compact chamber is applicable in pre-compliant EMC and general Research & Development RF testing.
-
product
DC Power / Energy Absorber Test System
AMETEK Programmable Power, Inc.
The Energy Absorber Test System includes power supplies and a regenerative energy absorber with a rating of 400VDC at ±150A. The system consists of DC power supplies, an AC distribution and interlock system, an energy absorber chassis and an absorber load resistor chassis. The power sources are equipped with a remote control option allowing control via GPIB or with front panel controls in local mode. The operation of the specific parts of the system is described in the sections below.
-
product
Testing Large Radar Sensors with CATR Technology
CATR Radar Test System UTP 5069
Modern driver assistance systems must recognize increasingly complex traffic scenarios and convert them into appropriate vehicle reactions with the help of artificial intelligence (AI) and specific algorithms. Imaging radar sensors with a higher spatial resolution, so-called imaging radar sensors, are therefore required. These can better distinguish larger from smaller objects and, due to the larger antenna apertures, also require larger dimensions of the test environment or larger far-field distances. Testing these sensors in the direct far field ( UTP 5065 ) would therefore require very large absorber chambers up to ten meters in size and more.Our efficient test system UTP 5069 offers exactly the right solution:By using CATR technology (Compact Antenna Test Range), 4D, imaging and other radar sensors with large far-field distances are calibrated with high precision in a small footprint. With the extremely low-reflection NOFFZ absorber chamber, the system is very well suited not only for validation, but also for EOL tests.
-
product
Towing Dynamometer
RS-200K
RS-200K towing dynamometer is designed for testing Class A trucks and is the most full-featured, reliable and accurate towing dynamometer in the industry. The RS-200K is built with a heavy-duty steel frame, heavy-duty industrial axles and rides on an air ride suspension. The RS-200K is designed to maintain 200,000 Newtons of constant drawbar pull and the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there are nolead-acid batteries to charge and testing is unlimited at low speeds.
-
product
Anechoic chambers
The anechoic chambers are built up as a modular construction. Due to individual modules any size of chamber can be manufactured. Big chambers may require an outer supporting structure or alternatively the shielding material can be attached direct to the building. The absorbers are fixed to rails bars or wooden base construction which is inserted into the shielding modules.
-
product
Towing Dynamometer
RS-80K
RS-80K towing dynamometer is designed for testing Class B trucks and is the most full-featured, reliable and accurate towing dynamometer in the industry. The RS-80K is built with a heavy duty steel frame, heavy-duty industrial axles and rides on an air ride suspension. The RS-80K is designed to maintain 80,000 Newtons of constant drawbar pull and the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there are no lead-acidbatteries to charge and testing is unlimited at low speeds.
