Filter Results By:
Products
Applications
Manufacturers
CAT 7
telecommunication premises cabling standard operating at 600 MHz. AKA: Category 7
- Pickering Interfaces Inc.
product
PXI 8-slot BRIC Multiplexer, 80-Channel, 10-Pole (7 Sub-cards)
40-570A-415
The 40-570A-415 is a 80-channel, 10-pole High-Density Multiplexer and is part of our BRIC family. The 40-570A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
product
7/16 DIN Connectors
Pasternack 7-16 DIN connector category includes many part numbers, most are RoHS and REACH compliant. 7-16 DIN connector series in this category will terminate to coax or terminal. Our 7-16 DIN connectors are built to precise industry specifications. 7/16 DIN connector items are available in male or female gender with 50 Ohm impedance. 7-16 DIN connectors are available in straight or right angle versions, as well as, 4 hole flange, bulkhead, 4 hole panel or mountless options. These DIN 7-16 connector designs include clamp/solder, crimp/solder, field replaceable or solder attachment methods. Like the other over 40,000 RF, microwave and millimeter wave Pasternack products, this 7/16 DIN connector series is in-stock. Not only are the 7 / 16 connectors in stock, but they will also ship the same day as they are purchased.
-
product
Low Cost Splitter Systems
RATCAT Family
The CAT Snake Stage Box allows four lines of balanced analog audio to be run down a shielded CAT5/6/7 cable. Each of its four channels can carry balanced analog, AES/EBU, DMX, and Clear-Com signals hundreds of feet away. The CAT Snake is a fully passive unit which can be input directly into analog or digital consoles. Each channel is isolated which means channel 1 can send a DMX Signal while channel 2 is sending balanced analog all down the same shielded CAT5 cable. Multiple CAT Snake stage boxes can be daisy chained to allow the same four analog channels to be dropped in multiple locations. Each CAT Snake stage box has an Ethercon input and Ethercon parallel output that allows the CAT Snake to be used as a hard-wire split.
-
product
Circuit Breaker Analyzers & Timers
CAT Standard Series
Circuit breakers are being tested during manufacturing, commissioning or maintenance stages. The most basic test requires timing measurement using circuit breaker timer. Their primary role is timing and motion measurement of medium and high voltage circuit breakers. Devices from CAT Standard series have suitable application in:electric power generation,distribution system,part of the electric power transmission system,contractors testing,and industrial environments.CAT Standard series meets the requirements of an easy to use circuit breaker timer and analyzer with an attractive price. Furthermore, they are portable and lightweight (weighs only up to 7 kg). Finally, the plastic case is unbreakable and has IP67 protective rating when the lid is closed.CAT Standard series includes five models:Three circuit breaker timers – CAT03, CAT31, and CAT61Two circuit breaker analyzers – CAT34 and CAT64CAT03 is a basic model intended only for timing measurement of main contact operations on the circuit breaker with one break per phase. Unlike CAT03, CAT31 has the possibility of circuit breaker operation initiation, coil current measurement, and auxiliary contact timing measurement. CAT61 differs in comparison to CAT31 by its ability to measure up to two breaks per phase.CAT34 and CAT64 are more advanced compared to CAT31 and CAT61, respectively, since they have additional analog channels. Also, they have the possibility of a travel curve recording.A user can download the test results to a USB memory stick or save it to internal memory. The CAT Standard series internal memory can store up to 500 test results (numerical and graphical data). Optional thermal printer prints test results in tabular and graphical form on 80 mm (3.15 inch) paper rolls. CAT Standard series instruments are compatible with DV-Win software. It provides full control of all CAT functions from a PC, as well as acquisition and analysis of test results.
-
product
LAN Tester RJ45
CZ20250
This easy to operate LAN tester enables you to test your wiring and connections at installation or after maintenance, and is a great Cat 5, Cat 6 and Cat 7 cable tester, making it one of the most convenient tools on the market. With the press of a single button you can automatically run a barrage of tests, including tests for Continuity, Opens, Shorts, Crosses and Splits. You can also identify which pairs require correction; The unit will scan all combinations without you having to do anything other than initiate the test. Even cable shield is tested for continuity! And it tests for all these at lightning speed, saving you as much time as possible.
-
product
7 Tesla Optical Cryostat
OptiCool®
The OptiCool by Quantum Design is a new optical cryostat using an innovative design that puts the sample volume in the heart of your optical environment. A custom 3.8 inch bore, split-coil, conical magnet offers fields perpendicular to the optical table up to ±7 tesla. The highly integrated design means, even with a magnet, your sample isn’t buried inside a large cryostat, far away from the optics. Seven side optical ports and one top optical port allow for optical access to your sample from a wide array of directions.
-
product
CompactPCI Chassis 7 Slots
4U 42HP
The Hartmann CompactPCI 4U system platform provides an intelligent, practical packaging solution for high-performance processors. This versatile desktop model provides a 7 slot 3.3 or 5V I/O 3U cPCI backplane for vertical mounting of boards.
-
product
IND AC/DC CAT IV TRMS Clamp Meter
ACDC-3400
The Amprobe ACDC-3400 clamp multimeter is CAT IV rated to add an extra level of safety for high voltage, industrial or utility testing applications. It is an AC/DC current clamp meter and a voltage meter all in one.
-
product
TB-2621, 37-Pin D-Sub (Female) terminals, 150V CAT II
779444-01
37-Pin Female D-Sub to 37-Pin Female Screw Terminal, PXI Module Mount Terminal Block - The TB-2621 provides an industrial PXI front-mounting terminal block for 37-pin D-SUB modules such as the PXI-6521 PXI Digital I/O Module. It features a 150 V CAT II rating, 2 A max current, screw-terminal connectivity, and a strain-relief bar.
-
product
Carrier - Virtex 7 W/FMC Site
VPF: 3U VPX
The VPF is a VPX form factor (VITA 46), FPGA processor board designed to meet the needs of challenging, embedded high‐performance digital signal processing applications at a competitive price point. AMD Virtex 7: VX330 and VX690 population options are available. The Virtex 7 FPGA provides impressive processing capabilities and supports operations such as: FFTs, FIR filters, fixed‐point and repetitive processing tasks. The VPF FPGA node processes input from the FMC HPC (Vita 57.1) site, allowing for maximum application configurability and performance when coupled with DEG’s market leading ADC and DAC FMC modules (250MSPS to 4.0GSPS). The VPF is fully compliant with the OpenVPX standard and accommodates the PCIExpress Gen 3.0 communication protocol. Delphi also offers a VPF FPGA Design kit which allows customers to leverage and modify DEG source code, develop within an open architecture, and rapidly integrate FPGA HDL. The DEG FPGA Design kit includes: Source code, simulation test bench and utilities to support custom algorithm development. Embedded Linux, VX Works and Windows software drivers are available. HPC FMC Site, Fully Compatible with all Delphi ADC and DAC FMC Modules.
-
product
CAT III Digital Multimeter
82600
Measures AC/DC voltage/current up to 600V and 10A, capacitance, diode, duty cycle, frequency, resistance, temperature and transistor. Includes 13 Functions and an operating temperature range between -40° to 1000°C. Features manual or auto shutdown after 15 minutes of inactivity, protection against overload at all ranges, data hold, low battery indicator and warning alarm. Also includes a LED flashlight for low light situations. Rubber outer case adds protection against drops and a stand bracket to hold meter at viewing angle and test probe holding clips.
-
product
NEXTest 7
PK-2030/2032/2033/2036/2037/2038
NEXTest 7 is an advanced and unique tester in the market. It's designed to check and troubleshoot the pin connections of Display port & HDMI prior to installation on equipment. By using advanced technology to verify the integrity (20 pins + shield) of both display port and HDMI cables, especially for HDTV installation and DIY termination in the field, solving your cable testing need, unlink all of the other testers verify 9 circuits only. It checks for opens, shorts, miswires and intermittent faults in all conductors plus shield continuity, most tester only test for opens. It displays cable map results of both TX (near end) and RX (far end) on the main unit, either on testing before or after installation cables. User can easily read and determine the actual 21 pins configuration on main unit. It employs both auto and manual scanning of 21 wires. Tone Generator mode transmits two selectable tones on each pin for use with Net Probe (PR-06P) optional, enables one to quickly locate a cable. It's capable of testing up to 8 cables and locations at one time. NEXTest 7 especially features a self-learning mode to memorize cable pin out for testing large quantity standard or custom cables for PASS/FAIL a snap, makes testing quick and more efficient.
-
product
7 Round Pin Tractor-Trailer Circuit Tester
IPA7865
Troubleshoot male and female 7 round pin tractor trailer electrical circuits on both the truck and trailer side. Allows bypassing of troubled circuitry while on the road.
-
product
7 Flat (Spade) Pin Trailer Circuit Tester
PT7893
Easily test trailer plug circuitry on most new light trucks, SUV's and RV's. Just plug the plug tester into the trailer plug socket and activate the lights, brakes, turn signal etc.
-
product
PXI 8 Slot BRIC 105x16 1-Pole (7 sub-cards)
40-561A-121-105X16
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
Triple Alarm CAT IV Non-Contact Voltage Detector with Flashlight
FLIR VP50-2
The FLIR VP50-2 is a durable, CAT IV-rated non-contact voltage detector featuring light, vibration, and beeper feedback alarms and a powerful LED flashlight. Use the VP50-2 to reliably check if an AC circuit is live before beginning work; detect voltage on exposed conducting parts or through insulation; identify live wires within electrical panels, switches, and outlets; or trace live wires and map circuits. With an ergonomic and drop-tested design, the FLIR VP50-2 is the right choice for professionals performing field troubleshooting and verification of electrical installations within residential, commercial, and industrial buildings.
-
product
Near Field Microprobe E-field 7 MHz to 3 GHz
ICR E150
The near field microprobe is used to measure electric fields at extremely high resolution and sensitivity. The optimal distance to the object being measured is < 1 mm. Due to its small probe head dimension, the probe has to be moved by a manual or automatic positioning system, e.g. Langer-Scanner.
-
product
7 Spade Pin Circuit Tester / Maintenance Kit
#8028
Innovative Products of America
Test, clean and restore 7 spade pin connections.The tester will verify that the tow vehicle is sending proper signal to the connector, while accompanying cleaning tools will remove corrosion, and verify proper pin size on both male and female truck/trailer plugs. For use with 7 spade connectors. Quickly tests, cleans and repairs truck and trailer connectors Extends harness life Great preventative maintenance tool Promotes safety and limits road hazardPatentedKit Includes: #7893: 7 Spade Pin Circuit Tester, #8023: Connector Cleaners, and #8030: 2 ml DeoxIT Cleaner
-
product
Signal, Contact, ITA, TriPaddle, 7 Amp, 26-28 AWG
610110169
Primary mating contact 610110167. (May mate with other Receiver contacts, as well.)Specifications Operating Voltage & Current 7 Amps Max. Continuous (20 AWG)Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 4000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
-
product
PXI 12-Slot BRIC Matrix, 154x8 1-Pole (7 sub-cards)
40-562B-321-154X8
The 40-562B-321-154X8 is a high density BRIC12 matrix module with a size of 154x8 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
PXI 8-slot BRIC Multiplexer, 40-Channel, 20-Pole (7 Sub-cards)
40-570A-315
The 40-570A-315 is a 40-channel, 20-pole High-Density Multiplexer and is part of our BRIC family. The 40-570A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
product
Decade Box, Calibrated W/Data, Resistance, 7, 1ohm to 11.11111Mohm, 1 %
72-7270 CAL D
The 72-7270 CAL D from Tenma is a resistance decade box. It is ideal for service, prototype and experimental use. This useful tool may be set resistance value from 1 to 11,111,110 ohm in one ohm increments. The decade accuracy is ±1% resistors used throughout. It has weight of 320g/0.70lb and dimension 14.7cm × 11.7cm × 5.5cm (5.79" × 4.61" × 2.16"). It is typically used in general applications, troubleshooting, maintenance, education and vocational training, production line testing, radio and TV services, working standards, research design & develop, physics laboratory work.
-
product
PXI 8-Slot BRIC Matrix, 203x8 2A 2-Pole (7 Sub-cards)
40-565B-102-203X8
These modules are 2 Amp high-density large PXI matrix modules with the ability to switch up to 2 Amps at 150VDC/100VAC. These 2A switch matrix modules are available in 2, 4 or 8-slot PXI sizes for most high-performance PXI matrix requirements. Constructed using quality electro-mechanical relays for high switching confidence.
-
product
Signal, Contact, Receiver, TriPaddle, 7 Amp, 20-24 AWG, Crimp/Solder
610110125
Signal, Contact, Receiver, TriPaddle, 7 Amp, 20-24 AWG, Crimp/Solder.p/n 610110125 TriPaddle Receiver 50µ" AU platingp/n 610110101 TriPaddle Receiver 30µ" AU platingThis contact primarily used in CASS applications.
-
product
PXI 8-Slot BRIC Matrix, 308x4 2-Pole (7 sub-cards)
40-562B-122-308X4
The 40-562B-122-308X4 is a high density BRIC8 matrix module with a size of 308x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
PXI 8-slot BRIC Multiplexer, 5-Channel, 160-Pole (7 Sub-cards)
40-570A-015
The 40-570A-015 is a 5-channel, 160-pole High-Density Multiplexer and is part of our BRIC family. The 40-570A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
product
IND CAT IV TRMS Clamp Meter with Temperature
ACD-3300
This CAT IV rated ACD-3300 IND Clamp On Tester is ideal for industrial applications and utilities that require an extra level of safety. Including True-rms sensing for accuracy, this clamp on meter’s extra large jaws can clamp on to those wide diameter wires making taking measurements in industrial environments simple.
-
product
8-Slot BRIC, 896x4, 1 Pole, PXI Matrix (7 Sub-cards)
40-559-801-896x4
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
PXI 8-Slot BRIC Matrix, 2A 1-Pole 406x6, 7 Sub-cards
40-596A-107
The 40-596A-107 is a PXI 1-pole 406x6 matrix in BRIC8 format and is part of a range of high density matrix modules able to switch up to 2 A or 300VDC/250VAC. The 40-596A BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
product
PXI 8-Slot BRIC Matrix, 35x32 1-Pole (7 sub-cards)
40-562B-121-35X32
The 40-562B-121-35X32 is a high density BRIC8 matrix module with a size of 35x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
PXI 8-slot BRIC Multiplexer, 20-Channel, 40-Pole (7 Sub-cards)
40-570A-215
The 40-570A-215 is a 20-channel, 40-pole High-Density Multiplexer and is part of our BRIC family. The 40-570A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
