Filter Results By:
Products
Applications
Manufacturers
Couplers
enable a signal to be used in another circuit.
- LBA Group, Inc
product
Digital RF Power Monitor
3024
The COMM-connect 3024 RF Power Monitor from LBA Technology can control up to 8 external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. The Power conversion algorithms handles multi carrier, multi mode, peak, average and RMS signals. The power readout is auto scaled and VSWR can be calculated between any probes. Also the measured and calculated results along with alarms can be shown in the local LCD. The instrument has SNMP support to allow network management. The instrument can be configured for VSWR and Power limits to give alarms. The alarms can be configured to operate relay drivers or isolated Optcouplers. The alarms can also be configured as SNMP traps sending relevant information to the network control center. The COMM-connect 3024 WEB enabled RF Power Monitor gives an unlimited number of applications to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
product
Simulating Optical Design Components
Wave Optics Module
The Wave Optics Module provides dedicated tools for electromagnetic wave propagation in linear and nonlinear optical media for accurate component simulation and optical design optimization. With this module you can model high-frequency electromagnetic wave simulations in either frequency- or time-domain in optical structures. It also adds to your modeling of optical media by supporting inhomogeneous and fully anisotropic materials, and optical media with gains or losses. It is straightforward to simulate optical sensors, metamaterials, optical fibers, bidirectional couplers, plasmonic devices, nonlinear optical processes in photonics, and laser beam propagation.
-
product
FBT Coupler
TRIPLE WINDOW
MAINTAINS OPTICAL OUTPUT UNIFORMITY.- Telcordia Standard- Minimal effect of Temperature change- High Stability- Low Insertion Loss
-
product
Directional Couplers & Bridges
A complete line of coaxial single and dual port directional couplers, and bridges for isolating, separating, and combining RF and microwave signals in such applications as power monitoring, source leveling, swept transmission and reflection measurements.
-
product
Pump Combiners
Pump combiners, also called pump couplers, are special application fiberoptic couplers used for sending pump and signal light into an amplifier or laser fiber. Because of these applications, pump combiners are specially designed for high-power use.
-
product
3x3 1x1 2x2 1x2 Couplers
Couplers can be used to split light from one or more fibers onto two or three fibers or to combine light from two or three fibers onto one or more fibers.
-
product
Analog Output Module For Remote I/O
The Analog Output Module for Remote I/O features a 2-wire spring terminal connection, selectable output ranges (0 V to 10 V, ±10 V, 0 V to 5 V, ±5 V, 0 mA to 20 mA, 4 mA to 20 mA, and ±20 mA) output ranges, and short circuit proof outputs. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Analog Output Module for Remote I/O from a real‐time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low‐cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high‐speed or specialty measurements.
-
product
Hybrid Coupler
Broadband 90 and 180 degree hybrid couplers with low loss and high power handling
-
product
Coupler And Decoupler Used With Lightning Impulse Simulation Tester
All electric equipments & systems is required Impulse Simulation Test to the to be tested under the condition where the power source is applied to the product-under-test.At this test condition, the decoupler is needed to reduce the impulse flowing through the power line while testing. And the coupler which is inserted between tester and product, to simulate the actual condition, so the electric circuit of decoupler is prescribet by IEC rules.
-
-
product
IPM Drive
IPM drive photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a photo diode and signal processing circuit on the output side in a single chip. This coupler is a high common mode transient immunity (CMR), high CTR type whose pulse width changes according to the operating temperature, making it ideal for driving IPMs (intelligent power modules).
-
product
Hose Couplings
WITT quick couplers / hose couplings SK100 for gases provide a safe, quick and distinctive connection of the hose with outlet points or working equipment.An automatic cut-off valve prevents any gas flow when disconnected. WITT hose couplings have an integrated non-return valves which prevents the formation of explosive gas mixtures in the pipeline.
-
product
Inductive Coupler
CLAMPMITTER™
The CLAMPMITTER™ is a unique tool for inductive coupling. This self-contained inductive transmitter increases productivity, promotes safety and simplifies locates by condensing the transmitter and inductive coupler into one cordless package. Whether climbing down a manhole or accessing a utility box, the Clampmitter is an easy alternative to suiting up with a full transmitter and wired coupler.
-
product
Additional Components
High-quality Splitter, Coupler and RF over Fibre Solutions. Made in Germany.
-
product
Integrated Couplers/ Harmonic Mixers
These waveguide bandwidth integrated coupler/mixers are designed to allow phase locking or signal monitoring of compact millimeter wave systems. RF inputs and outputs are on opposite sides of a thin wafer to obtain minimum insertion length. These devices use silicon Schottky barrier beam-lead diodes on a rugged stripline circuit. Nominal coupling value is 10 dB. For coupling values greater than 10 dB, non-directional coupler models are available (consult factory).
-
product
Ear Simulator
BO1028
The BO1028 Ear Simulator is a special coupler for microspeakers or earbuds that has been designed to be compliant with ATU-T P.57 and IEC 60318-1. While mics in our BP1090 couplers receive sound waves the way they travel through air, the dual compartment chamber of the BO1028 is designed to modify sound pressure so that the mic receives air vibrations the way a human ear drum would receive them.
-
product
RF Calibration Kit
SMK-3000
The SMK calibration kits are precision, high power calibration standards that are used to calibrate RF radios, wattmeters, directional couplers and other high-power RF test equipment in the field or metrology lab. Unlike other calibration solutions, the SMK-3000 calibration kits reduce the cost of ownership and provide a much faster time-to-calibration with lab precision and accuracy you’ve come to expect from Bird.
-
product
Polarization Maintaining Collimator
Zhongke Rayzer Optical Technology Co.,Ltd
The basic element for in-line PM fiber optics components, such as PM Isolator, PM FWDM, PM Filter Coupler and PM Circulator. It has high extinction ratio, low insertion and high return loss. The unique processing and high quality AR coating also enable this collimator tohandle high power.
-
product
Couplers Splitters And Multiplexers
Passive optical devices that are used to split an optical signal into at least 2 and as many as 64 signals.
-
product
Signal Conditioning
To get most out of high-quality sensors, accurate, low-noise processing of the sensor signals that are emitted is essential. Kistler offers an attractive portfolio of solutions for signal processing and subsequent data digitization. Piezoelectric (PE) sensors with a charge output require a so-called charge amplifier. On the other hand, piezoelectric sensors with integrated electronics (IEPE) are supplied by Piezotron couplers which decouple and amplify the signal.
-
product
Fuel Injection Pressure Tester w/2 Gages & Quick Couplers
53950
Tests gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Quick couplers provide for fast and easy hook-up.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Tests all Chrysler cars with Multi-port turbos and some TBI.Use on most Ford TBI systems equipped with or without small Schrader test valve.Tests all Ford vehicles with Multi-port fuel injection systems.
-
product
PhotoIC Couplers
Panasonic Industrial Devices Sales Company of America
A Commercialized PhotoIC Coupler For High-Speed Communication Between Industrial Equipment. Panasonic, a worldwide leader in cutting-edge electronic components, has developed and introduces the NEW APS1 Series PhotoIC Coupler that transmits light signals while allowing electrical insulation. This revolutionary new product is designed for high-speed transmission of signals between industrial equipment such as motors and PLCs.
-
product
Optical Fiber
Thorlabs' full line of optical fiber and fiber optic components are presented here. This includes our industry-leading selection of bare optical fiber and fiber optic patch cables as standard stock items. In addition, custom fiber patch cables can be ordered and shipped within 24 hours. Also available is an extensive line of optical fiber components including collimators, polarization controllers, fiber optic couplers, WDMs, circulators, and attenuators, as well as all of the tools and supplies needed to terminate, inspect, and clean optical fiber and fiber components.
-
product
Coupler Metrology
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Rosenberger provides directional coupler-based measurement techniques as well as probes for comprehensive cross-domain coupling analysis.Nowadays, the introduction of new accessories within vehicles, like rear seat infotainment, smart dashboards, and various advanced driver assistance systems, has increased the demand for high-speed automotive bus systems working in parallel with the high-voltage power networks in electric cars.
-
product
Couplers
Macom Technology Solutions Holdings Inc.
MACOM’s couplers are used extensively in a wide range of aerospace and defense, wireless, and wireline communications applications. Our directional and hybrid couplers are offered in a variety of connectorized and surface mount packages with a broad range of coupling values ranging from 6 to 30 dB. Operating at frequencies from 2 MHz up to 18 GHz our couplers are ideal for real-estate constrained customers who need a high performing device for easy assembly.
-
product
Waveguide Coupler
ZDC8-30W32.9-50G-2389
Crossguide Coupler, Frequency 32.9~50GHz, Coupling 30dB, Waveguide FUGP400, 2.4mm Female
-
product
Needle Hydrophones
Our high-performance needle hydrophone system consists of a range of interchangeable PVdF needle hydrophone probes, a submersible wide-band amplifier and a DC coupler.
-
product
Passive Component Integration - MATRIQ
The Passive is a highly customizable benchtop accessory that can integrate the passive components of your choice for convenient storage and integration into your test set up.We can customize the Passive module with a wide range of passive components: WDM couplers, splitters, circulators, band-pass filters, PM beamsplitters, MUX, DeMUX and more.Our spec sheet contains a selection of popular configurations.Please contact us to discuss your specific requirements at sales@quantifiphotonics.com.
-
product
Signal Splitters
Becker Nachrichtentechnik GmbH
Becker Nachrichtentechnik GmbH offers a comprehensive portfolio of active multicouplers and bi-directional signal splitters for duplicating RF signals from common sources. The multi-couplers are designed in 50 ohm technology and are available as a 19 ", 1 U devices as well as slot-in modules for our 'Modular RF Systems' platform. With help of the slot-in modules, larger scale distribution structures can be realized in a space-saving and cost-effective manner. Some devices are available in variants for AC or DC power supply and provide service-friendly remote monitoring capabilities. For use in the production of infotainment components special multi-couplers with integrated HF and DC test functions are available. The multi couplers are used in applications like radio monitoring and direction finding, in product development, validation, manufacturing, quality assurance and in the field of research.
-
product
VHF & UHF Couplers for the PowerMaster and PowerMaster II
VHF-1.5K (2m), VHF-1.5K-2 (1.35m), UHF1.5K (440-450 MHz), UHF-1.5K-2 (420-440 MHz)
-
product
4-Channel Broadcast Monitor
The COMM-connect Entry Level Broadcast Power Monitor type 3025 can control two external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. Equipped with the RMS Probes the Power conversion algorithms handles multi carrier, multi mode signals. With the 3026 Diode base probe the power readout gives good repeatable results. The power readout is auto scaled and VSWR will be calculated between the two probes. The COMM-connect Entry Level Power Monitor gives a number of application to monitor and control the last part of your RF network installation from transmitters to the antenna.
