Filter Results By:
Products
Applications
Manufacturers
-
product
VMEbus Repeater Link
VME-REPEAT-A-L
The VME-REPEAT-A-L is a two-board set which allows VMEbus slave I/O boards residing in one VMEbus chassis to be controlled by a VMEbus master residing in another chassis. The VMEbus chassis in which VMEbus masters reside is referred to as a master chassis, while the VMEbus slave boards reside in a slave chassis.
-
product
Transformer Regulation
Transformer Parallel Control System is designed to monitor & control the tap changers of up to four (4) transformers connected on a common bus & operating in a MASTER FOLLOWER control configuration.
-
product
One Phase Electric Power/Energy Calibrator
MC133
The MC133 master unit model is a one phase electric power/energy calibrator. It can supply the device under test with single phase precise voltage and current with calibrated phase shift along with DC voltage and current capability. Output voltage can be set in five ranges up to 280V and output current in six ranges up to 30A. Simulated electric power can be set independently for each phase. Frequency can be set from 15Hz to 1 kHz with resolution 0.001Hz to 0.01Hz. The MC133 Calibrator is equipped with 5 1/2 digital DC meter with DC ranges 20mA or 10V for direct calibration of various types of power transducers and wattmeters.
-
product
Digital I/O PXI Card
GX5280
The GX5280 Series are high performance, cost-effective 3U PXI dynamic digital I/O boards with 32 TTL input or output channels and 32 LVDS input or output channels. The GX5280 Series offers an industry leading 512 MB of on-board memory and supports test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
product
I2C Fast Mode Interface for USB 2.0, I2C Multimaster and Monitor
Connii MM 2.0
telos EDV Systementwicklung GmbH
Connii MM 2.0 is a small, compact, easy-to-use solution for a PC driven I2C transmitter and receiver. The I2C interface works as an I2C multimaster device. Thus, it is able to drive buses running multiple I2C bus masters. Additionally, Connii MM 2.0 is a limited I2C monitor for traffic up to 400kHz.
-
product
High Performance High Power DC Electronic Load
IT8900A/E Series
IT8900A/E series high performance high power DC electronic load provides three voltage ranges 150V/600V/1200V, stand-alone power from 2kW to 54kW. IT8900A/E series, with ultra-wide voltage and current range, controlled by an independent master unit.
-
product
Ethernet-based Distributed Systems
DMC-3425
The DMC-3425 is the first product in Galil's new E-Series line designed specifically for Ethernet-based distributed systems. The DMC-3425 provides a highly versatile and powerful form of distributed control where multiple DMC-3425 controllers are linked together. When linked, one DMC-3425 is designated as the master over the other DMC-3425 controllers in the distributed system.
-
product
Dynamic Digital I/O (3U), 32 Channel, 50 MHz
GX5291-50
The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 digital input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.Dynamic Digital I/O (3U), 32 ch. up to 50 MHz w/128MB On-Board Memory, 32-ch Domain.
-
product
EtherCAT Master Multi-Axis Motion Controllers
DMC-52xx0
The DMC-52xx0 EtherCAT Master is Galil Motion Control's first 32 axis motion controller. It is a pure EtherCAT controller capable of controlling up to 32 drives and 2 IO modules on one EtherCAT Network in a small, space efficient package. The DMC-52xx0 makes configuration and programming easy with just a handful of EtherCAT configuration commands and Galil’s intuitive, two-letter programming language. The DMC-52xx0 is offered in 2, 4, 8, 16, and 32 axis formats. Coordinated moves can be done within banks of 8 allowing for minimal changes to Galil’s programming language. Galil supports a variety of EtherCAT drives to accommodate most applications. The DMC-52xx0 operates in Cyclic Synchronous Position mode (CSP). In this mode the servo control loop is closed on the EtherCAT drive while the Galil sends motion profile data at a 1 kHz rate. The DMC-52xx0 features 8 uncommitted opto-isolated inputs and 8 uncommitted opto-isolated high power outputs. It also includes 8 uncommitted analog inputs and 8 uncommitted analog outputs. One 100 Mbps Ethernet port and one USB (serial) port are provided for communication with a host PC or external devices.
-
product
Cylindrical Inductive Proximity Sensor (Built-In Amplifier)
GX-300
Panasonic Industrial Devices Sales Company of America
The GX-300 Series of Cylindrical Inductive Proximity Sensors provide state-of-the-art features, enhanced basic performance, improved operability, and an extensive model lineup including IO-Link compatible models that are capable of transmitting sensor data and status information to a host controller through an IO-Link master.
-
product
Brake Fluid Refractometer
DOT3 Fahrenheit
Fahrenheit model – The MISCO Palm Abbe Brake Fluid Refractometer is a precision digital instrument designed for measuring the water content, and estimating the boiling point, of DOT3 brake fluids. It only takes two drops of brake fluid to get an accurate indication of water content or boiling point in only seconds. Brake fluid may be measured from the master cylinder or from each of the wheel cylinders.
-
product
EOC Master
EOM-7224
Hangzhou Softel Optic Co., Ltd.
*EOCM-7224 is the integrate EOC Master with two EOC master module and one ONU module.*EOCM-7224 EOC Master can provide high speed data service based on coaxial cable network. EOCM-7224 built in a ONU. *The module supports IEEE 802.3ah standards. It provide one SC/PC optical EPON uplink port and two 10/100/1000Mauto-negotiable Ethernet RJ45 ports. By using the EPON technology, the ONU Module can provide a high-speed data channel through a single optical fiber with a rate of 1.25 Gbit/s on bi-direction. In addition, it offers the QOS, flexible bandwidth allocated to provide quality high-speed data service, voice service, and video service.
-
product
Redundant Frequency and Timing Systems
A unique feature of our frequency standards and distribution amplifiers is that the two separate parts of the redundant system are identical and can easily be inter-changed, for maintenance purposes. What we mean by this is that that we don't have a "Master" unit and a "Slave" unit. Whatever unit is powered up first becomes the master unit and the other becomes the slave unit.
-
product
10A Continuity Tester
EQUITEST
EQUITEST is connected to its master unit via C2050 cable and to the mains for power supplying.Please refer to the user manual of your HT installation safety tester for the compatibility to EQUITEST.
-
product
Automated CMM Calibrated for High-Production Shop Floor Inspection
CMM Master
The CMM Master provides process control by delivering optimal price and performance to your application. The system brings highly repeatable, thermally insensitive, versatile, and programmable inspection to the shop floor.
-
product
Field Master 3 Electric Fence Charger
FM-3
Power to stop the most stubborn stock! For small to medium pastures. The all new low impedance model for small to medium pastures features advanced solid state circuitry. Shocks through wet weeds and brush. New color coded fence and ground terminals. Red to the fence and Black to ground. Fuse protection, with built-in lightning arresters. Full 3 year warranty covers damage caused by lightning.
-
product
IRIG Time Code Receiver & Generator Module
TCR180
Meinberg Funkuhren GmbH & Co. KG
The module TCR180 has been designed to receive and to generate IRIG-A/B/G, IEEE 1344, IEEE C37.118 or AFNOR NF S87-500 time codes. It is used in applications like data acquisition, standalone computer time synchronization (for systems without a network connection or higher accuracy requirements) or as an IRIG converter device. The frequency locking of the master oscillator to the time code system enables this module to generate fixed and programmable standard frequencies with high accuracy and stability. Various oscillator options allow the cost efficient implementation of different requirements concerning the accurracy of the outputs. The generator of the IMS-TCR module generates pulses per second and per minute and per hour. Four programmable outputs are also available. The pulses are synchronized to UTC-second.
-
product
Master Controller
RatMaster
- Jumper free configuration- Intuitive configuration software- RS-232, TTL and CI-V interfaces- Automatically generates Icom CI-V data stream from non-Icom radios- Configurable band limits- Built-in USB interface- Set default antenna per band- Field upgradeable firmware- Anodized aluminum case- Laser engraved panels
-
product
FerruleMaster Ferrule Auto Test Instruments
CA3003
FerruleMaster could feed, focus, measure and classify the ferrules automatically. It could test over 1000 PCS ferrules in one hour, no laborer required. Ferrule Master has the high performance and accuracy and high repeatablility with the superior image processing. It is intelligent and easy to operate and maintain. Clear user interface, easy to operate, stable performance and powerful analysis capability make the Ferrule Master is the best instrument in material inspection and mass production.
-
-
product
Digital I/O PXI Express Card
GX5292e
The GX5292e is a high performance, cost-effective 3U PXI Express dynamic digital I/O boards offering 32 TTL or LVDS input or output channels with dynamic direction control. The GX5292e also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 100 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
product
Wattmeter
PowerMaster II for SO2R
The Power Master II wattmeter has the ability to have two couplers connected to it, and it has provision to allow switching very easily between the two couplers through only two button presses on the front panel.When operating SO2R, you do not want to have to toggle from one coupler to another. We make matched couplers available for SO2R users and due to the nature of these couplers being high impedancedevices, we can actually connect the two coupler inputs in parallel and instead of toggling between the two couplers, they will both be connected and active at the same time. The first step is to disconnect all connections to the rear panel of your Power Master II and remove the two #6-32 philips screws on either side of the cabinet.
-
product
Optical Switch
5504
The FOD 5504 Optical Switch is a unique handheld instrument for calibration sets and measurement automation. Routine comparison with Master device procedures in calibration laboratories, can be simply performed with before unachievable repeatability. No more need to move fiber and connect it repeatedly. Fix cables on a table, only once clean and connect patchcords.
-
product
Cab Signal Master
Cab Signal Master is a microprocessor based system specially developed to test all cab signal equipment in railroad locomotives and transit cars. Programmable default setting and straight forward operations allow simple "plug it in, turn it on" operation with very little instruction.
-
product
Test Sockets
Yamaichi Electronics Co., Ltd.
A test socket is the ideal point to test your home’s internal phone wiring for faults. You can also use it to identify any potential faults with the phone line outside. Your test socket is located in your master socket. It is the point between the internal phone wiring in your house and the phone line outside. That means by plugging into your test socket you can bypass all the internal wiring and test your device directly on the phone line.
-
product
Master Relay & Fused Circuit Test Kit
69300
Includes 8 Jumpers to fit most popular relays. Includes Test Lead Kit for easily and securely connecting Relay Test Jumpers to a multimeter. Terminal Leads with switch, fuse and power options provide easy access to check current or voltage on many fuses and relays used on vehicles today. Also allows testing of relay configurations not covered by our eight Relay Test Jumpers, Like Volkswagen, BMW and other European vehicles. Relay Puller Pliers easily remove electrical relays. Works without piercing wires.
-
product
VME Controller With USB-2 Interface
VM-USB
The VM-USB is a VME master with high speed USB2 interface. Enhanced functionality is given by the programmable internal FPGA logic which provides a VME command sequencer with 4kB stack and 28kB data buffer. Combined with the 4 front panel I/O ports this allows VME operation and data acquisition / buffering without any PC or USB activity.
-
product
Analysis Tool
CANalarm
Gesellschaft für Mikroelektronikanwendung Chemnitz mbH
The CANalarm is a low priced analysis tool that can be installed in the bus permanently. It makes it possible to build up a separate and redundant monitor without change of configuration and program of the master controller. It works passive and is therefore non reactive
-
product
Inline Handler W/Bypass Line Master
6TL35
A perfect basis for a heavy-duty, reliable, high precision, and automatic integrated Test system for medium to high demanding environments. Important technical and economic advantages due to their modular structure and expansion capability are evident. The production testing environment will be flexible and efficient, helping towards the always valued Return of Investment.
-
product
Sand And Dust Test Chambers
Dongguan Amade Instruments Technology Co., Ltd
Sand and dust test chamber is also referred as dust-proof chamber, which is able to simulate the sand storm by putting the test piece in the chamber to judge the damage of sand-and-dust weather to products. Equipment is mainly applicable to determination of sealing performance of product shells based on the IPX5 and IPX6 degrees. Testing machine features a flow of air carrying dust in a vertical circulation, resulting in cycle use of sand during the test. Sand and dust testing has great significance to master the specimen’s performance to defend the penetration of dust particles, to withstand the abrasion of sands.
