Filter Results By:
Products
Applications
Manufacturers
-
product
High Current / High Voltage Pulsers
DEI Division
Berkeley Nucleonics Corporation
is optimized for high impedance capacitive loads, driving extraction grids and deflection plates, and pulsing or gating power tube grids. It generates an output voltage of 6,000 volts with rise and fall times less than 60ns, with very flat voltage pulses from 160 nanoseconds to DC into a capacitive load.
-
product
Switched Filter Banks
Switched Filter Banks typically include multiple filter topologies, including PIN diode and MMIC switch sub-circuits to achieve operational bandwidths of greater than 3 octaves. Pin Diode Based Switched Filter Banks provide the highest level of signal isolation, higher operating power levels, and lower insertion loss and achieve switching speeds of < 40 nanoseconds. GaAs MMIC Based Switched Filter Banks provide switching times as low as 10 nanoseconds with very low power consumption and have the inherent advantage of supporting multi-octave frequency bands with extremely low power consumption.
-
product
Intensified Cameras - Ultra-Sensitive CMOS Cameras from Deep UV to NIR Spectrum
iCameras
The cameras are equipped with a high-resolution sensor with high frame rate for excellent quality of image production, which is well‐suited to detect high speed moving objects or ultra-fast phenomenon.The mechanical architecture of the iCamera is small, compact and light-weight, especially designed for easy integration into any system.The iCamera features an exceptional sensitivity based on high QE image intensifier - ultra-fast gating technology down to a few nanoseconds, which allows it to be coupled with a laser source to perform high fidelity active imaging.
-
product
NTDS I/O Analyzer
The NTDS I/O Analyzer provides insight and visibility, enabling users to quickly and efficiently analyze timing relationships, message protocols, throughput, and data integrity on all types of NTDS interfaces. It is capable of monitoring any combination of NTDS Parallel Type A, B, C, H and NTDS Serial Type D, E channels as defined in the MIL-STD-1397 revision B and C specifications regardless of NTDS mode. The channels are connected to existing NTDS cabling with NTDS tap boxes and extract ongoing communication. Each word of NTDS information received is time-stamped with a 125 nanosecond resolution clock ensuring highly accurate timing measurements. Data collected is stored locally for analysis and can be transmitted to external equipment enabling remote troubleshooting, event reconstruction, or time-critical feedback on system performance.
-
product
Manage Power, Thermal & Control Planes In Real Time
Platform Manager 2 & L-ASC10
*Full fault coverage – monitor all rails and temperature nodes*Manage from 10 to 80 supplies using just the required number of L-ASC10 hardware management expanders*Minimize fault propagation by enabling individual hardware management sub-blocks (power, thermal & control path) to respond to faults in other blocks within nano-seconds*Save CPLD I/O pins by eliminating the need to monitor power-good signals of DC-DC converters*Reliable power & thermal fault detection in hardware, as opposed to software routines
-
product
Pulse & Delay Generators
The benchtop pulse generators feature a fast risetime and low jitter. Our most popular digital delay pulse series 575 and 577 generators are now available with selectable time references. With up to eight channels of delay and width control, each individual channel's reference can be set either to the trigger or to any other channel. So look below if you require a picosecond pulse generator or nanosecond pulse generator for your application.
-
product
Tunable Wavelength Systems (OPOs)
NT342 Series
NT342 series tunable laser system comprises a nanosecond optical parametric oscillator and Q-switched pump laser in a single housing. The system features up to 50 mJ in VIS, no-gap wavelength tuning from 192 nm to 2600 nm, up to 30 Hz repeptition rate, easy maintenance and separate output for pump laser beam.
-
product
SparkFun GNSS Timing Breakout
ZED-F9T (Qwiic)
The SparkFun GNSS Timing Breakout offers a unique entry into SparkFun's geospatial catalog featuring the ZED-F9T GNSS receiver from u-blox. The ZED-F9T provides up to five nanosecond timing accuracy under clear skies with no external GNSS correction making it perfect for applications where timing accuracy is imperative. Need an extremely accurate time reference to maximize the efficiency of your IoT network of 5G devices? The ZED-F9T GNSS Timing Breakout could be the perfect solution.
-
product
Hawk - E Co Processor
9322 E
Basic Hawk Co-Processor card set with 2.0 Mbyte memory and microcoded instructions for Nova 4X and Eclipse S280. Executes ALU instructions in 275 nanoseconds. ISA bus compatible, two slots required. Approximate CPU performance of actual S280.
-
product
Binary BCD Converters
Computer Conversions Corporation
The BCD Series of BCD to Binary Converters will convert 4 digits of scaled BCD angle data with a full scale of 359.9degrees into 12 Bits of binary angle data (MSB=180degrees). These units are entirely digital, require no timing or control signals and do this conversion in less than 500 nano-seconds. Logic levels are TTL/DTL compatable and +5V DC power is required. They are packaged in a 2.6 x 3.1 x .82" H PC board mounting module.
-
product
- RS-232 DB9 Lightning Suppressor
Model 29
FEATURES: PC 386/486 Pentium Com Ports; Nanosecond Response; DB9 Connectors; Protects All 9 Lines; Ground Stud & Wire Included. The Model 29 contains avalanche diodes, one for each line. All diodes are returned to a ground stud. The Model 29 is provided with a 2-foot ground wire and has male and female DB9 connectors.
-
product
Nanosecond Pulsed Lasers
Our nanosecond pulsed lasers feature pulses in the ns range. For picosecond and femtosecond lasers please see Ultrafast Lasers.
-
-
product
Ka-band Power Amplifier (33-37 GHz, 10 Watt Output Power)
*Frequency band, GHz: 33-37 *Output power, typical, W: 10 (40 dBm) *Gain, dB, typical: 30*Gain flatness: 2 dB Max *Pulse width, Max.: 100 nanoseconds - 60 microseconds *Pulse reptition frequency: up to 100 KHz *Oprating temparture: -40 deg. Celsius to 60 deg. Celsius *Dimensions: 245 mm x 124 mm x 30 mm
-
product
Camera Link Frame grabber
Cyton-CXP
CoaXPress (CXP) is a simple, yet powerful, standard for moving high speed serial data from a camera to a frame grabber. Video is captured at speeds of up to 6.25 Gigabits/Second (Gb/S). Simultaneously, control commands and triggers can be sent to the camera 20 Mb/S (with a trigger accuracy of +/- 2 nanoseconds). Up to 13 W of power can also supplied to the camera.
-
product
Air-Cooled Nanosecond DPSS Laser Head
BH9206-80
The BH9206‐80 laser series is a compact, air‐cooled nanosecond DPSS laser designed for industrial, scientific and military applications. Utilizing diode pumped, air‐cooled technologies, the BH9206‐80 is capable of producing 80mJ at 1064nm with repetitions rates up to 30Hz with a 6ns pulse width.
-
product
DFM (Deep and Fast Modulated) generators up to 280 GHz
Insight Product Company offers DFM (Deep and Fast Modulated) mm-wave sources at frequencies from 30 to 280 GHz. DFM generators are designed to go swiftly from the generation to the non-generation mode and back. This process controlled by the external TTL signal. ON/OFF switch time is approximately 2 nanoseconds.
-
product
Interface
R15-EC
The R15-EC card provides the highest level of performance and density for MIL-STD-1553A/B in an ExpressCard form factor. The R15-EC card provides 1 or 2 channels integrated with powerful API software that provides instant access to all 1553 databus functionality and data. Standard features include real-time bus playback (with ability to edit out RTs), aperiodic message insertion, error injection/detection, conditional BC branching, 64-bit, 25 nanosecond message timetagging, and “Oneshot” BC operation. The Bus Monitor mode provides 100% bus monitoring of a fully loaded 1553 bus. IRIG-B Receiver (AM or DC/TTL) Generator (DC/TTL) optionally available.
-
product
Pulse Laser
Is a variable, pulsed high power laser source, a building block ideal for MOPA, LIDAR, OTDR laser systems development and applications. This fully integrated compact module contains a Distributed Feedback (DFB) laser and built-in optical amplifier stage, and a variable nanosecond pulse generation circuits. It provides up to 200 mW optical peak power in 1064 nm wavelength region, with a programmable pulse width from 10 ns to 1000 ns, and a selectable pulse repetition rate from 100 Hz to 1 MHz The optical pulse generation can alternatively be controlled via an external electrical trigger. In a compact design, NPL-CWDM-M is applicable for OEM integration or as a stand alone pulsed laser source. Contact Optilab for more information.
-
product
Shunts
WSM alternating current measuring resistors have compared with traditional direct current shunt resistors with coaxial voltage tap significantly better high-frequency transmission characteristics. This resulted from a production engineering very complicated structural design of the active part.ISM pulse current measuring resistors allow the metrological recording of the time curve fast current changes large amplitude in the nanosecond range. The ISM are designed for the pulse current measurement with broadband oscilloscopes.
-
product
GPS NTP Time Server - SYNTIME
Signals & Systems India Private Limited
Your product description goes hGPS NTP Time Server (SYNTIME) for Network Time Synchronization is a highly accurate time server. It generates time protocols to synchronize NTP/SNTP clients (Simple Network Time Protocol)/PTP clients (Precision time protocol IEEE 1588) over the network and operates at a speed of 10/100/1000Mbps. The NTP server accepts the time and frequency signals from sources like GPS or GLONASS. It achieves nanosecond accuracy and the system clock operates at stratum 1 when synchronized with time sources. It is a sleek, rack-mountable unit that synchronizes and maintains equipment/device time and avoiding any time drifts due to local RTCs. NTP output from time server supports unicast, broadcast, and multicast methods based on selection and behaves like a reference clock for the network. Apart from time synchronization protocols, it supports MD5 (Security key), SNMP, SSH, HTTP (Configuration), TELNET, FTP, and SYSLOG. IP address of the LAN ports can be field configurable.
-
product
SEM- Based Dectors
ScintiFast™
ScintiFast™ is El-Mul’s flagship scintillator technology enabling the next generation of detectors with shorter response time and higher sensitivity. Recently released, ScintFast™ has the highest available photon yield for the nanosecond scintillator category. ScintiFast™ is the scintillator of choice for detectors in SEM-based tools for the semiconductor market as well as in Time of Flight Mass Spectrometry instruments.
-
product
High Level of Customization at an Affordable Price
TLP
The Impulse transmission line pulser (TLP) discharge networks are easily integrated with other instruments for a custom system matched for your device and process applications. Specifications include 1-10 nanosecond rise times, up to 40 amps peak, for 10-500 nanosecond pulse widths. It is a proven design incorporating 15 years of hardware and device development experience. Reliable performance over hundreds of processes, and thousands of products. All TLP systems are built by special request, contact us with your specifications or application.
-
product
UV Nanosecond Lasers
355 nm wavelengthPower: 0.5W* to 5W*Air-cooled design, water cooled optionAll-in-one (AIO) single box design for 0.5 & 1W modelPatented intracavity UV generationCompact, rugged, monolithic laser headTotal pulse controlTEM00 beam with typical M² < 1.2Pulse rates from 1Hz to 300kHzRS232 computer controlField replaceable pump diodes
-
product
Diode Laser Driver
D200
The D200 is a compact, DC-coupled fast laser driver, providing up to 4 amps of regulated constant current. A built-in edge-triggered pulse generator produces up to 1 microsecond pulse widths and 2 nanosecond transition times, capable of driving lasers with forward voltages up to 9 volts. A pulse-follower mode is also provided, accommodating externally-defined trigger widths up to 100% duty continuous-wave (CW). Power, pulse width, drive current and differential triggering functions are accessible through a ribbon cable header for embedded OEM applications. A low-inductance laser drive interface permits direct laser connection or custom interposer and flex-cable attachment.
-
product
Synthesizers
Offering synthesizer architectures supporting operating frequencies from 0.1 to 40 GHz. Our direct analog and digital designs feature fast switching speed of less than 100 nanoseconds and ultra-low phase noise. Our wideband indirect synthesizer designs support your requirements for smaller size and lower power consumption and offer typical switching speed of less than 500 microseconds. Composite architecture designs (Direct and Indirect Synthesis) are also available to optimize phase noise, switching speed, size and power consumption.
-
product
SPDT PIN Diode Switches
Fairview offers a comprehensive selection of 23 different models of SPDT PIN diode switches that cover frequencies ranging from 10 MHz to 67 GHz. The high isolation levels up to 80 dB ensure that unwanted signals will not leak into the desired signal path. Other critical performance features include low insertion loss as low as 1.1 dB and fast switching speed performance as low as 50 nanoseconds. Both absorptive and reflective designs are available and every model utilizes integrated TTL compatible high speed driver logic circuitry. These SPDT switches are constructed using MIL-Grade rugged coaxial packages and several models support field replaceable connectors. All models are EAR99.
-
product
Flashlamp Pumped Actively Q-switched Lasers
NL300 Series
NL300 series electro-optically Q-switched nanosecond Nd:YAG lasers provide up to 800 mJ per pulse at 1064 nm. A wide range of harmonic generator modules for generation up to a 5th harmonic (213 nm) is available. The NL300 series nanosecond lasers are an excellent choice for many applications, including laser ablation and marking, OPO pumping and other critical tasks.
-
product
Jitter Free I/O Access Fast Data Acquisition
TiCoBasic
Shortest available reaction time for fast data acquisition, open- and closed-loop control! This focus of Jger Messtechnik is greatly intensified by the new TiCo processor, which enables real-time processing in the scale of nanoseconds. The TiCo (Timing Controller) being implemented into a Xilinx FPGA enhances the approved ADwin systems by a close-to-I/O, extremely fast pre-processing.
-
product
Radar Level Gauge
HRRD730 Series
HighReach Measuring & Controlling System Co.,Ltd
At The Radar Level gauge Antenna emits and Narrows at The Microwave Pulse. This Pulse propagates in Space AT at The Speed of Light. The When IT Encounters at The Surface of at The the Measured Medium, Part of the ITS Energy IS the REFLECTED the Back and Received by at The Same, Antenna. At The Time interval The Between the transmitted pulse and the received pulse is proportional to the distance from the antenna to the surface of the measured medium.Because the electromagnetic wave propagation speed is extremely high, the time interval between the transmitted pulse and the received pulse is very small (on the order of nanoseconds). It is difficult to confirm. The 90X series 26G radar level gauge uses a special demodulation technology To accurately identify the transmitted pulse and the time interval of the pulse is received to further calculate the distance of the antenna from the surface of the measured medium.
