Filter Results By:
Products
Applications
Manufacturers
- TEAM SOLUTIONS, INC.
product
Four Port RS-232 Interface
PCI-COM232/4
Serial ports: 4Configured: Address and interrupt configured through PCI BIOS and supplied driversMax. baud rate: to 460.8 Kbps, software selectable per channel for 115.2, 230.4, or 460.8KbpsSerial modes: 5, 6, 7, or 8 data bits; odd, even or no parity; 0, 1 or 2 stop bitsUART: 16C550 standardInterrupt Status: Each UART interrupt status read from any UARTís Scratchpad RegisterConnector: 37 position D-type with fanout cable to 4 DB-9 or DB-25 male connectorsPower: +5V only
-
product
Serial To Digital Interface MiniBox™
ICS's 2363 Serial Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications. OEM board versions available for inclusion in test chassis.
-
product
Becker Transponder Test Fixture
TA-3400
This transponder test fixture is specific to the requirements for testing Becker Avionics Transponders and provides interface connectors for both the panel mount and remote systems. The panel also provides switches to implement Gillham code altitude as well as separate interfaces for an external parallel or serial encoder. The panel will interface with the RMU 5000 or standard control head. This fixture also comes with voltage and current meters along with an internal dimming source. This panel comes in the standard 19 inch rack width and measures 12 inches in depth.
-
product
Camera Modules
e-con Systems Camera Modules come with parallel & MIPI interfaces. Our CMOS camera modules will be effective in any application or environment because of their versatility and wide range of options. Embedded camera module can be interfaced to processors like Tegra K1, i.MX6, DM3730, OMAP. Further to these HD camera modules, e-con offers evaluation boards with these camera modules interfaced to various development boards featuring these processors. We provide Omnivision Camera Module & Aptina Camera Module (ON Semiconductor) with CMOS Sensors.
-
product
4000W to 50,000W - Single Output
ALE-Rack Mount Series
*Compact, lightweight design*Simple parallel operation for higher power*Worldwide input voltages/frequencies*Fully adjustable output voltage*Full remote control interface*Safety agency approvals
-
product
96/48-CH Opto-22 Compatible PCI Express Digital I/O Cards
PCIe-7248/7296
ADLINK"s PCIe-7248/7296 are high-density parallel digital I/O boards with 96/48 I/O channels. The header connectors are fully compatible with industry Opto-22 standard. Thus, PCIe-7248/7296 can utilize the Opto-22 external devices. The PCIe-7248/7296 devices emulate mode 0 of the industry standard 8255 programmable peripheral interface (PPI) chips. The PCIe-7248/7296 provides 4/2 PPI chips respectively. Each PPI offers three 8-bit ports: Port A, Port B and Port C. The Port C is divided into 2 nibble-wide (4-bit) ports. The PCIe-7248/7296 devices have programmable timer/counters. One 16-bit counter is available for event counting, while the other 32-bit timer is available for timed interrupt generation. The PCIe-7248/7296 devices provide multiple programmable interrupt sources from DIO channels, as well as the output of the timer.
-
product
50 MHz 32-CH High-Speed Digital I/O Card
PCIe-7350
ADLINK's PCIe-7350 is the advanced version of hot-selling PCI/PCIe-7300A featuring high-speed digital I/O with 32-channel bi-direction parallel I/O lines. The data rate can achieve up to 200 MB/s through the x1 PCI ExpressR interface. The clock rate can support up to 50 MHz internal clock or 100 MHz external clock, which is ideal for the applications of high-speed and large-scale digital data acquisition or exchange, such as digital image capture, video playback and IC testing.
-
product
Ethernet To Parallel Digital Interfaces
ICS's 8063 Ethernet Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications.
-
product
NTDS I/O Analyzer
The NTDS I/O Analyzer provides insight and visibility, enabling users to quickly and efficiently analyze timing relationships, message protocols, throughput, and data integrity on all types of NTDS interfaces. It is capable of monitoring any combination of NTDS Parallel Type A, B, C, H and NTDS Serial Type D, E channels as defined in the MIL-STD-1397 revision B and C specifications regardless of NTDS mode. The channels are connected to existing NTDS cabling with NTDS tap boxes and extract ongoing communication. Each word of NTDS information received is time-stamped with a 125 nanosecond resolution clock ensuring highly accurate timing measurements. Data collected is stored locally for analysis and can be transmitted to external equipment enabling remote troubleshooting, event reconstruction, or time-critical feedback on system performance.
-
product
Efficient All-In-One Test Solution for Low-Cost IoT Devices
KT RFCT 2400
The low price point creates a cost effective means for testing wireless communication units, while generating a favorable cost to performance ratio.The calibrated RF test system has a small footprint, integrating seamlessly into test system infrastructures via a single Ethernet connection. GPIOs control the DUT and peripherals. The test system enables communication interfaces like SPI, I2C, UART and CAN. Simple Go/No-Go tests can be performed in parallel. The KT-RFCT 2400A features a 70 MHz to 6 GHz frequency range and includes non-signaling and signaling connections. Bluetooth signaling standards are supported up to 4.1 as well as BT-LE. WIFI signaling standards supported are a, b, g, n and ac.The KT-RFCT 2400A is the perfect test system for a wide range of applications, such as Bluetooth, Infotainment, Keyless Entry, Tire Pressure Measurement, GPS and WIFI.
-
product
e-CAM1M_CU10630_MOD - 1MP OV10633 Custom Lens Camera Module
e-CAM1M_CU10630_MOD is a High Dynamic Range (HDR), Wide Dynamic Range (WDR), custom lens camera module targeted for surveillance and security applications. This HDR camera module based on the OV10633 sensor from OmniVision is e-con’s first Wide Dynamic Range (WDR) camera module that can stream 1280x720p video at 30fps over its 8-bit digital video parallel interface. This 1MP WDR/HDR camera module is compatible with almost all of the popular Application Processor families such as TI OMAP, TI Sitara, NXP/Freescale i.MX, Marvell Xscale, Samsung etc and also compatible with Digital Signal/Media Processors such as TI OMAP35x, TI DaVinci DM37x, DaVinci DM3xx etc. This 1MP WDR/HDR camera module is compatible with almost all of the popular Application Processor families such as TI OMAP, TI Sitara, NXP/Freescale i.MX, Marvell Xscale, Samsung etc and also compatible with Digital Signal/Media Processors such as TI OMAP35x, TI DaVinci DM37x, DaVinci DM3xx etc. The camera module is mounted with an industry-standard S-mount M12P0.5 lens holder allowing our customers to choose a lens of their choice. The camera module is mounted with an industry-standard S-mount M12P0.5 lens holder allowing our customers to choose a lens of their choice.
-
product
Single-Channel Voltage Output D/A Converters
Analog Devices offers a broad portfolio of single-channel voltage D/A converters, which includes many leading products in performance and package size, with resolutions from 8-bit to 20-bit, low power, and a serial SPI, parallel, or I2C interface. Within the industry’s smallest packages, we offer more functionality within smaller board and module sizes. The integration of a precision reference minimizes board area and costs, eliminates the need of calibration, and reduces the number of external components to simplify the design stage.
-
product
PCI Three-Axis High Performance Laser Board with External Sampling
N1231B
The Keysight N1231B PCI Three-Axis Laser Board with External Sampling is a register based PCI bus board that implements three axes of laser interferometer measurement for position monitoring and closed-loop servo control. There are four external sample inputs along with four data hold inputs that allow easy synchronization with user systems. Several threshold compare registers, with both hardware outputs and interrupt capability, can be used for travel limit and in window or out of window detection functions. The dual mode hardware position outputs, controlled by the hold inputs, provide either a 32-bits/axis parallel interface or a 36-bit multiplexed interface to the 36-bit axis position data at rates up to 20MHz. The user can programmatically access the externally sampled position and velocity data, as well as software sampled position and velocity data, over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
product
GPIB Digital Interface
Model 4863
ICS's 4863 GPIB Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications. OEM board versions available for inclusion in test chassis.
-
product
Programmable Gain Amplifiers
Analog Devices programmable gain amplifiers (PGAs) provide excellent gain accuracy, channel-to-channel matching specifications, and low 1 ppm/°C drift. Set your gain with a simple serial or parallel interface from 1 V/V to over 4000 V/V.
-
product
1.3 MP Custom Lens NIR Camera Module (Monochrome)
e-CAM10_CU0130_MOD
The e-CAM10_CU0130_MOD is a 1.3 MP NIR Camera module (Monochrome) based on the Aptina / ON Semiconductor AR0130CS CMOS image sensor with S-mount lens holder attached to it. The AR0130 is a 1/3” Optical Form factor, Electronic Rolling Shutter CMOS sensor with enhanced sensitivity in the Near Infrared region and superior low light performance. The e-CAM10_CU0130_MOD is designed to connect with any Application Processor that has parallel digital video interface. The standard S-Mount lens holder can accommodate a wide range of lenses based on the customer choice. e-CAM10_CU0130_MOD’s S-Mount holder can also house a fisheye lens or a zoom lens to meet their application requirements.
-
product
GPIB Parallel Interface
Model 4813
* Provides 128 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Optional Relay Driver boards add 64 or 128 Relay Drivers.
-
product
IP-Parallel-BA1 "IP-Tape"
The IndustryPack compatible IP-Tape design adds 48 digital parallel IO lines to one slot of your carrier board. The IO is dedicated to a DTC interface. Other interfaces can be implemented. The DTC interface has 22 Address, 16 Data plus Parity, 4 control and 5 status lines. Parity is automatically generated in write mode and checked in read mode.
-
product
LCR Meter, Hand Held, 100 kHz, 2 kH, 20000 µF, 0.2 Gohm
72-10465
The 72-10465 from Tenma is a LCR meter in orange and grey colour. It features an easy to read dual LCD (40mm x 63mm) display measurement of 19999/1999 (main/auxiliary). It also has series and parallel measurement modes which can be used to select quality factor, loss factor, phase location angle and equivalent resistance of measure articles. Intelligent detection and five different test frequencies enable accurate readings for all sizes of capacitors and inductors. The user can also access the stored data on a PC with the included USB connection and interface software. The compact size and case make this unit far more portable than a benchtop meter.
-
product
C012 Communication Board
MS 1728/29
- Suitable for standard desktops- Four channel in single board- Up to 10 Mbits/sec operating speed- Low Cost solution- Standard INMOS link protocol- Communicates with transputers- Converts between serial link and parallel bus- Tristate bidirectional bus interface- Memory mapped registers- Interrupt capability- TTL compatibility
-
product
Serial Parallel Interface
Model 2303
* 2303 Board provides 40 high-power TTL I/O lines that can sink 23 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Dual Serial headers support conections with baud rate switch inputs or to a Serial Flat Ribon Cable Assembly. * Optional Relay Driver board drives 24-40 relays. * 114732 Board has the DIN connector on circuit side for use with the X3DVR Relay Driver Board or for piggyback mounting.* All other specifications are the same as listed above for the 2303.
-
product
Ethernet To Parallel Digital Interface Boards
ICS's Ethernet Parallel Digital Interface boards provide the user with a wide range of IO signals that can be user configured to match virtually any application. These Ethernet boards are available with high power relay driver boards and with optional firmware designed to simplify switching applications. The 80x3 boards have high-power TTL signals that can sink 48 mA and source 24 mA. Pullup resistors make it easy to interface with CMOS logic and to sense contact closures. User configures data byte direction and polarity. The 80x3 boards are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE and support raw socket connections. The new 8113 board is a CMOS close of the 8013 board with user set 3.3 or 5 V logic levels. Pinouts and command set is the same as the 8013 board. The 8113 communicates with TCP/IP(Raw Socket) protocoland and also has a RS-232 Serrial Port. All boards are designed for mounting against the rear panel or inside a chassis and use our Ethernet Wiring Kit for easy connection to a Ethernet Connector on the rear panel.
-
product
32 Channel Multi-Purpose DIOS/TAP Modules/Interfaces for Spare JT 2148 QuadPOD Transceiver Slot
JT 2149/MPV eMPV
The JT 2149/MPV and the JT 2149/eMPV are a 32 channel multi purpose DIOS/TAP pod modules/interfaces that can be plugged into any spare JT 2148 QuadPOD transceiver slot. The DIOS channels of these units I/O interface pods enable increased fault coverage and thus improved diagnostic resolution during boundary-scan testing. The principal difference between the two versions is the use of an extended case on the eMPV that allows standard 0.1″ connections to be used to access ths TAP and static IO signals (see tab below)- on the standard /MPV unit these signals are available at the front face 0.05″ connector. The units are fully supported by JTAG Technologies’ development tools. Additional DIOS modules can be serially connected if more parallel access points are required.
-
product
5.0 MP Custom Lens Camera Module (Monochrome)
e-CAM50_CU9P031_MOD
e-CAM50_CU9P031_MOD is a 5 MP custom lens monochrome camera module based on Aptina's MT9P031 CMOS image sensor with S-mount lens holder attached to it. The MT9P031 is a 1/2.5" Optical Form factor, Electronic Rolling Shutter CMOS sensor. The e-CAM50_CU9P031_MOD is designed to connect with any Application Processor that has parallel digital video interface. The standard S-Mount lens holder can accommodate a wide range of lenses based on the customer choice. e-CAM50_CU9P031_MOD’s S-Mount holder can also house a fisheye lens or a zoom lens to meet their application requirements.
-
product
Basic Power Supply - 80 W Max Output Power
NGA100
The R&S®NGA100 DC power supplies are linear, compact and easy to use in diverse scenarios. All models have excellent readback accuracy with a low-current range for demanding measurements. Data logging, arbitrary waveforms, built-in statistics and remote sensing features make the instruments ideal for various bench applications, such as:- R&D;- Creating IoT low power designs - Manufacturing- Education- General purpose use casesEquipped with a number of different remote interfaces, including USB and Ethernet, R&S®NGA100 DC power supplies are also great for automated tests. The channel fusion feature extends voltage and current range. Get up to 200 V with the R&S®NGA142 in serial mode and up to 12 A with the R&S®NGA102 in parallel mode. Advanced protection functions keep devices connected and power supplies safe.Choose the DC power supply for your use case by selecting the base unit and necessary options in our online configurator. This makes the procedure easy and fully price transparent for fast processing of your order request by our authorized distribution partners. Click "configure and quote" to start your configuration.
-
product
Ethernet Parallel Interface
Model 8013
* Provides 128 high-power TTL I/O lines.* Fully VXI-11 Compliant plus Raw Socket for easy programming with Visual Basic or C, Agilent VEE and LabVIEW.* Standard board has a horizontal Ethernet connector and 150-pin Digital IO connector on the component side. * Mates to Relay Driver Boards with 64 or 128 Relay Drivers.* Mates to 115650 Connector Board with 4 flat ribbon headers.
-
product
Serial Parallel Interface
Model 2313
* Provides 128 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Separate headers for RS-232 and RS-485 signals. * Optional 2313 Flat Ribbon Cables mount DE-9 male or female connectors on the rear panel. * Optional Relay Driver boards with 64 or 128 Relay Drivers.
-
product
Fixed Mount Strobes
Our fixed mount stroboscopes are designed for installation in applications requiring continuous stroboscopic visual inspection. The MVS is available with xenon or LED light output with adjustable pulse width and focal distance for optimized target illumination. Connect your existing trigger signal or the optional Frequency Controller with LCD. Connect multiple units together in parallel for applications with wide illumination area requirements. Use the optional Audio Interface Box and microphone to create stunning audio driven visual effects.
-
product
PXI-6529, 48-Channel, Sink/Source Inputs, Channel-Channel Isolated PXI Digital I/O Module
779949-01
48-Channel, Sink/Source Inputs, Channel-Channel Isolated PXI Digital I/O Module—The PXI‑6529 is an industrial, parallel digital input interface. PXI‑6529 devices are ideal for a variety of applications from automotive design, industrial factory automation, and machine control to aerospace, laboratory research, and biomedical applications. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6529 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
Hyperspectral Cameras With USB3 Vision
XiSpec
*Smallest Hyperspectral camera - Compact, lightweight with only 26.4 x 26.4 x 31 mm, 32 grams (1)*Cost efficient - Excellent value and price through utilizing new imec hyperspectral imaging technology*Cool economy - Low power consumption with 1.6 Watt, minimal heat dissipation, ideal for UAV / UAS*All-around support - USB 3.0 support for Windows 7 and 10, macOS, Linux, ARM*Powerful potential - Highest spatial and spectral resolution, possible with 5Gb/s interface*Optimized - 2048 parallel, "on-chip" integrated spectroscopes with 100 points of spectral resolution each*AIA standard - USB3 Vision standard compliant*Industry standard interface - Compatible with USB 3.0 SuperSpeed specification*Fastest Hyperspectral camera - High speed, high frame rate: based on 170 fps at 2.2 Mpix resolution*Connectivity and Synchronization - Programmable optoisolated input and output, 3 status LEDs*Easy deployment - Range of accessories and wide hardware and software integration*Highly Customizable - Variety of sensor options, which can be further adjusted to match requirements*Interoperability increase - Continuous embrace of new software and hardware partners
-
product
Validation Testers
M Series
The M Series line introduces a new class of massively parallel SerDes validation testers that are ideal for high-volume data collection and characterization. Constructed using a collection of Introspect Technology’s D Series modules that are operated seamlessly using the Introspect ESP software, these massively parallel testers are able to interface to high-speed devices in their entirety.
