Filter Results By:
Products
Applications
Manufacturers
-
product
Electrodynamic Velocity Pickup
The principle of Reciprocal Pendulum type Pickup is to induce voltage by reciprocal motion of the seismic mass with a coil in the magnetic field being suspended by a diaphragm or coil spring.. Because of its High Sensitivity and Advanced Linearity, it is suitable for detection of malfunction or deterioration of rotational machineries. Due to its structure, mounting should be done carefully for its direction or angle.
-
product
Laser Tracker SMRs & Laser Tracker Ball Probes
Single Piece Aluminum InsertWe have assembled this SMR in a way that the insert will not come out. When you drop the competitions SMR they shift or pop out after a few short drops. With our Rhino Series SMR, Drop, Pickup, and Measure on. You get the performance of a solid SMR that is much more affordable. These are available in High Accuracy SMR versions. We keep the Rhino Series SMR s in stock at all times.
-
product
Leak Locator
XL-2
Lightweight & Strong11 Position filter to pinpoint leak and remove background sounds2 Sensitivity controlsSuper Sensitive magnetic transducerHigh gain, 4-stage amplifierVisual and Audible indicationsCoarse and Fine SensitivityExtremely sensitive pickup with removable 7" (177.8mm) probeBattery operated and with battery condition indicator
-
product
LoadLooker Ammeter
Instead of you manipulating a hinged or clamp-type inductive pick-up, the patented LoadLooker electronically closes the loop for you. Its unique U-shape jaw senses the amperage present between its tines.
-
product
Lock-In Voltage Preamplifier
SR552
Stanford Research Systems, Inc.
The SR552 Voltage Preamplifier is designed to work with SRS lock-in amplifiers, providing gain where it is needed most?right at the experiment. The preamplifier minimizes noise and pickup in the connecting lines and can reduce measurement time in noise-limited experiments.
-
product
Lock-In Voltage Preamplifier
SR550
Stanford Research Systems, Inc.
The SR550 Voltage Preamplifier is designed to work with any SRS lock-in amplifier. Preamplifiers provide gain close to the experimental detector, before the signal-to-noise ratio is permanently degraded by cable capacitance and pickup
-
product
Measuring Wheel
B20-S
Simple and light Measuring Wheel B20-s can measure up to 10,000m at 10cm graduation.The counter is indicated in 5 digits and has reset button. When we use Leak Noise Correlator LC-2500, we need to input the between pick-up sensors.
-
product
Piezoelectric Vibration Pickup
PU-8ALSF
*Side outlet type with assembled *cap nut*Built-in amplifier*Use up to 150 ℃ enabled
-
product
Piezoelectric Vibration Pickup
PU-661D
*Side outlet type*Waterproof (IPX7) and suitable for*high temperature(-10℃ to 150℃)
-
product
Piezoelectric Vibration Pickup
PU-6ALSF
*Side outlet type*Easy to remove due to cap nut type*Use up to 80 ℃ enabled
-
product
Piezoelectric Vibration Pickup
PU-626E
*Connector type with upper outlet*Waterproof (IPX6), suitable for a wide range
-
product
Piezoelectric Vibration Pickup
PU-611E
*Waterproof general purpose,*side outlet type*Water resistant(IPX7)
-
product
Piezoelectric Vibration Pickup
PU-8ANSF
*Side outlet*Easy to remove due to cap nut type*Use up to 150 ℃ enabled
-
product
Piezoelectric Vibration Pickup
PU-6GHT6
*High-sensitivity type for sensoring*low-rotation from 0.2Hz
-
product
Piezoelectric Vibration Pickup
PU-671D
*Upper outlet*Compliant with waterproof (IPX7) and suitable for high temperature (-10℃ to 150℃)
-
product
Piezoelectric Vibration Pickup
PU-8ALT6
*Upper outlet*Built-in amplifier*Use up to 150 ℃ enabled
-
product
Professional Automotive Digital Multimeter
CT8027
Full autorange features. Large 4 digit LCD display with analog bargraph. AC/DC Voltage measurement up to 600 Volt. AC/DC Current measurement up to 10 A. Tachometer function with inductive pickup measures from 30 to 20000 rpm
-
product
Programmable Voltage Reference Plug-In
ProDAQ 3202
The ProDAQ 3202 voltage reference card is used in the ProDAQ 3180 ultra-performance motherboards and LXI function card carriers. The ProDAQ 3202 voltage reference card is plugged directly onto the motherboard or carrier and can distribute the reference voltage to all ProDAQ function cards via two signal lines. This allows the distribution as a differential signal to overcome possible noise pick-up.
-
product
PWC Dynamometers
Mount the DYNOmite absorber (and appropriate pump adapter) in place of the boat's standard nozzle and cone. Each pump adapter (sold separately) incorporates a shaft, driven by the impeller (without impeller removal). A load control valve (fed from your " garden hose) allows you to regulate RPM by varying absorber drag (while holding the throttle open). You can simulate running at any MPH from idle to top end. The DYNOmite's computer captures the engine's RPM from an (integral absorber mounted) magnetic RPM pickup. Torque readings come directly from a full-bridge (temperature- compensated) torque arm. Results are never estimated from vague hydraulic-pump pressures.
-
product
Saluki SE4002 FET Input Preamplifier
The SE4002 is a low-noise, ultra-high input impedance preamplifier with excellent common-mode rejection. It is designed to work with any Saluki digital lock-in amplifier. The preamplifier minimizes noise and pickup in the connecting lines and reduces measurement time in noise-limited experiments.
-
product
Short Circuit Finders
The ShortSniffer locates short circuits in electronics circuits, projects, and printed circuit boards. * locates PCB shorts under solder mask, under components, and even on inner PCB layers * non-contact (inductive) pickup wand * pinpoint short to within 2mm radius (SS2) * rapid location with audio feedback * "follow the sound to the short" * no need for relative or reference measurements * battery operated * diode clamped current drive, won't harm your circuitry
-
product
Speed Pick-up
SU63
The Validyne SU63 is an AC inductive speed pick-up used for RPM measurement on high-speed rotating equipment. The SU63 is a tightly-wound coil with a laminated core that can be conveniently mounted on rotating equipment so that the magnetic field of a magnetized nut or part passes through the coil windings. The moving magnetic field produces a voltage within the coil proportional to its rate of change and the strength of the permanent magnetized part. The frequency of this inductive voltage spike is fed into an oscilloscope or counter to determine RPM.
-
product
Tachometers/Stroboscopes
Shenzhen Graigar Technology Co.,Ltd.
Measurement of the speed of a rotating shaft is a common requirement in many industrial and laboratory applications. Such measurements have usually been carried out in the past with the help of contact type tachometers with friction drive. More recently digital optical non-contact tachometers have been designed which count the reflected pulses from a white patch on the shaft and then display the speed in rpm. The light source is usually a filament lamp operating with dry cells leading to limited life and illumination. A similar ideawith magnetic pick-up from a particular area of the shaft has also been used for speed measurement.
-
product
Truck Chassis Dynamometer
Truck chassis kit includes: heavy-duty tube-steel frame and 30"-diameter "dually" wide-roll assembly with machined-in "traction grooves," air brakes, diamond-tread deck plate, floor anchors, wheel chocks, vehicle tie downs, eddy-current absorber and controller with overdrive, S-beam load cell, DYNOmite-Pro data-acquisition computer, inductive RPM pickup, DYNO-MAX software, electronic auto-load control, 28-channel data harness, engine-temperature thermistor, and more.
-
product
Vacuum Pen
Stand-alone vacuum pick-up system used for pick and place functions. Requires shop air or can be air powered through TS350 Series or TS500R dispensers/controllers. Features an adjustable vacuum control knob to set desired vacuum. Maximum operating pressure 100psi (6.9bar).
-
product
Vibration Analyzers
A vibration analyzer measures and assesses the machinery condition using vibration sensors such as accelerometers, displacement probes, and velocity pickups.
-
product
Vibration Pickup
Constructed so that each Piezoelectric element has shear that is proportional to applied acceleration between the poles. It is useful for low frequency vibration measurement even in the environments of large temperature change because of it is hard to be effected by the Pyroelectricity. Furthermore, it is less sensitive to the strain in the base.