Filter Results By:
Products
Applications
Manufacturers
Potentiometers
Measure the voltage in a circuit or function as voltage dividers.
See Also: Programmable Resistors
- Pickering Interfaces Inc.
product
PXI Resistor Module Dual 12-Channel (no resistors fitted)
40-281-021
The 40-282 is a potential divider with up 24 separate channels. This can be used to emulate potentiometer devices, each channel having a fixed R1 R2 ratio. Additionally, the centre point can be shorted to either of the potentiometer end points.
-
product
PXI Potentiometer Module 2x16 Bit, 0 Ohm to 65K Ohm
40-296-021-2/16
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
product
Power Monitor, AC-Powered, Field Adjustable
YMA/YQA
NAI's YMA and YQA Power Monitors are used to monitor voltage, frequency, and phase characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within predetermined limits.High and low voltage and frequency limits, and "pick-up" and "drop-out" time delay are field-adjustable using potentiometers. These power monitors are ideally suited for rugged defense and industrial applications.
-
product
PXI Potentiometer Module 4x16 Bit, 0 Ohm to 65K Ohm
40-296-121-4/16
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
product
High Power Digital Lab Series Regulated DC Power Supply – 3000W
- 3000W different combination- High current density.- 19″ rack adaptable -5U high- Remote sensing.- Front panel potentiometer to set V&I- 3Digit seven segment display for V&I- High stability and close regulation- Phase controlled preregulation plus linear post regulation Optional, at extra cost- Over voltage protection- 19″ rack mounting
-
product
Linear Potentiometers
They are one of the most common forms of measuring device for linear position. They are incredibly simple to use relative to other devices, infinite resolution, output is proportional to stroke length and very robust.
-
product
Rotary Potentiometers
Panasonic Industrial Devices Sales Company of America
Panasonic Center Space Rotary Potentiometers offer built-in LED options and automotive operating temperatures. Rotary Potentiometers still have many applications for the Medical, Automotive and Measurement Equipment markets and many more.
-
product
Universal Transmitter
Knick Elektronische Messgeräte GmbH & Co. KG.
Universal Transmitter for temperature, load cells / strain gauge, potentiometer and resistance in 6 mm housing. Functional safety up to SIL 2, SIL 3 redundant to parameterization via interface or intuitively, directly on the device. Universal use with 24 V DC or AC power supply.
-
product
High Elongation Extensometers
Model 3800
Jinan Testing Equipment IE Corporation
The main body of this unique extensometer remains stationary during testing, held in position by the adjustable magnetic base included. Only the very light, small traveling heads move as the sample elongates during a test. These attach to the sample with small spring clips. Each head pulls a cord out from the extensometer as the head moves. These models use high precision, low friction potentiometers, and, as a result, have a wide range of factory selectable outputs. The extensometer is driven by an excitation voltage and has output proportional to the input. They can be provided with high level outputs (approximately 2-8 VDC) or ones that mimic strain gaged devices (2-4 mV/V). When set to mimic strain gaged extensometers, the Model 3800 can be used with virtually any signal conditioning electronics designed for strain gaged sensors. The potentiometers employ a hybrid wire wound around conductive plastic, which provides excellent long term stability. The output from the extensometer is readily interfaced with most existing test controllers, and may be directly input to data acquisition systems and chart recorders. Please let us know at the time of order what type of output and connector you require.
-
product
SparkFun Multiplexer Breakout
8 Channel (74HC4051)
The SparkFun Multiplexer Breakout provides access to all pins and features of the 74HC4051, an 8-channel analog multiplexer/demultiplexer. The 74HC4051 allows you to turn four I/O pins into eight multifunctional, individually selectable signals, which can be used to do everything from driving eight LEDs to monitoring eight potentiometers.
-
product
Encoders & Potentiometers
Panasonic Industrial Devices Sales Company of America
Encoders convert the manual rotary operation of an actuator or knob into coded signal outputs and offer options such as various detents, high torque, push-on switch, long life, water proof and center space.
-
product
PCI Standard Programmable Resistor Cards
Pickering's PCI Standard Programmable Resistor Cards include fully programmable resistor and potentiometer cards for applications such as sensor emulation that require fine adjustment with a resolution down to 0.25 Ohm. All of our Programmable Resistor Cards can easily be formed to make Programmable Potentiometers by connecting two channels in series, using the unconnected terminals as the A and B connections and the link between the two channels as the wiper connection.
-
product
Suitable For Temperature And Potentiometer Sensors
SEM1600T
The SEM1600T accepts resistance or mV signals from RTD, Slidewire or Thermocouple sensors.
-
product
10Ch Electronic Potentiometer 8 Bit
YAV90084
The YAV90084 can work autonomously as a 10Ch electronic potentiometer of 8 bit resolution. By default, it features 10kOhm resistors), but other resistor values can be assembled under request.
-
product
Rotator Controller
RA-S1
The RA-S1 has four buttons that are used for configuration and to manually turn the rotator. It has two potentiometers POS and SPEED. POS is used to choose an angle to point-and-shoot and also choosing between options when the RA-S1 is on the setup mode.
-
product
Encapsulated Potentiometers
The R40 potentiometer can be supplied in a dust- proof housing. This has a transparent front cover with a scale to indicate the rotational position.
-
product
Signal Splitters
The DAT4530 can convert any process signal (Thermocouples, RTD, mV, Voltage, mA Resistance and Potentiometer) to a voltage or current output (4-20mA, 0-20mA or 0-10V). Each output can be different and it also has a built in limit alarm which is an SPST relay. The DAT4530 is PC programmable with the aid of the Prodat programmer and the Datasoft software which is available from the Datexel down load page. The DAT4530 is also programmable with the aid of 3 DIP switches which can be found on the side of the DAT4530. There is full isolation between the input, power supply, limit alarm output and two outputs.
-
product
PXI Potential Divider Module 24-Channel (no resistors fitted)
40-282-121
The 40-282 is a potential divider with up 24 separate channels. This can be used to emulate potentiometer devices, each channel having a fixed R1 R2 ratio. Additionally, the centre point can be shorted to either of the potentiometer end points.
-
product
Trip Amplifiers
Datexel manufacture a large range of Trip Amplifiers and Process Limit Alarms that accept universal inputs and provide either relays or NPN or PNP transistor outputs. The DAT5028 is also an isolated signal converter and has a local display with up to 4 relays and is DIP switch programmable. The inputs can be Thermocouples, RTD, mV, mA, Resistance, Potentiometers or Voltage. They can be supplied fully configured set up by PC or DIP switches. The DAT5024 is a trip Amplifier / Temperature limit alarm for RTD's, Thermocouples, Voltage, Resistance and Current with the option of 1 or 2 relay outputs hysteresis and delay timers. The DAT5024 E range is an economical choice with DIP Switch programmable for voltage or current input. Either 1 relay or 2 relays (SPDT) are available with delay timers.
-
product
PCI High Density Potentiometer Card 2-Channel, 12-Bit, 0 To 4k Ohm
50-296A-021-2/12
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
DC Precision Measuring
Precision instruments for calibrating and monitoring. Our line of Precision Bridges, Decade Boxes, Galvanometers, Potentiometers, and standard high precision resistors, allow customers the accuracy and quality demanded in a precision device.
-
product
PXI-2722,16-Bit, 5-Channel PXI Programmable Resistor Module
781985-22
16-Bit, 5-Channel PXI Programmable Resistor Module—The PXI‑2722 is a test module that replicates the behavior of resistance-based inputs and outputs such as potentiometers, resistance temperature detectors (RTDs), voltage dividers, and bridge elements. The PXI‑2722 programmatically controls a series of relays to vary the resistance across each channel of an I/O connector. This function is well suited for simulating environmental conditions in hardware‑in‑the‑loop (HIL) validation. The software provides a simple user interface that accepts inputs in units of temperature or resistance and configures the resistance across each channel.
-
product
Universal Development Board For The Plug-in Module PCAN-MicroMod FD
PCAN MicroMod FD Evaluation Board
The PCAN-MicroMod FD Evaluation Board is a development board for the PCAN-MicroMod FD and enables the design and development of your own circuits with CAN connection and I/O functionality. It can also be used for training purposes for CAN and CAN FD structures. The user can access the resources of the attached PCAN-MicroMod FD via taps, screw terminals, switches and potentiometers and test configurations or test circuits.
-
product
Resistance Measurement Trainer
Unitech Scales And Measurements Pvt. Ltd
Resistance Measurement Trainer comprises of potentiometer to vary the resistance with respect to the angular displacement with digital indicator to read the resistance change in the potentiometer.
-
product
Variable Resistors/Potentiometers
When a design calls for a variable resistance, CTS can supply a solution in the form of a wide variety of rotary and slide-action variable resistors / potentiometers.
-
product
Mini-Joystick Potentiometers
The CTS mini-controllers offer these features often found in many larger products:A choice of through hole or surface mountingA long 1 million cycle lifeA variety of resistance and tolerance optionsExcellent electrical accuracy with a patented mechanism (Pat. Nos.: US 7,199,314, Taiwan 279822, Pat. Pending in China)An optional momentary switch that is operational at all positions to allow excellent navigation and menu selection
-
product
PXI Potential Divider Module 12-Channel (no resistors fitted)
40-282-021
The 40-282 is a potential divider with up 24 separate channels. This can be used to emulate potentiometer devices, each channel having a fixed R1 R2 ratio. Additionally, the centre point can be shorted to either of the potentiometer end points.
-
product
Industrial Automation
NAI offers a variety of resolver-based Astrosystems motion control solutions for the packaging, material handling, and automated manufacturing industries. Specifically designed for rugged defense and industrial applications, our innovative product lines include single- and multi-axis synchronizers, limit switches, encoders, position sensors, and potentiometers.
-
product
Process Counters
TCT201-2ABC
The Process Counter TCT201-2ABC is a 1/16 Din 48 x 48 mm panel mount programmerable digital Counter with two 8 Amp relay outputs and up to 3 inputs. The TCT201-2ABC also has a potentiometer input that can accept either 5K or 10K Potentiometers. Other inputs can be PNP or NPN switches, 2 or 3 wire Proximity switches.
-
product
Electric Linear Actuators
MaxJac
The MaxJac actuator features a smooth high response ball screw and gear motor and utilizes a proprietary guidance bushing to provide precision smooth linear actuation. Standard equipment includes a 12 volt motor with potentiometer feedback. It is ideal for throttle control, solenoid actuation, and valve actuation in such applications as construction equipment, motor vehicles, marine, and blood infusion pumps.
-
product
Signal Conditioners
Datexel has a large range of Signal Conditioners. We manufacture Thermocouple Transmitters, that are either Head Mounted, Din Rail and we even have an OEM version that can fit inside an enclosure smaller than 1" x 1/4". These Temperature Transmitters are PC programmable or DIP Switch programmable. Some are isolated and accept input from various sensors such as RTD's, Thermocouples Voltages, Current, Resistance and Potentiometers. They have current outputs and we even have Temperature converters that have voltage outputs.
