Filter Results By:
Products
Applications
Manufacturers
Seismic Accelerometers
sense ground vibration.
See Also: Seismic, Seismometers, Seismic Arrays, Earthquake
- TEAM SOLUTIONS, INC.
product
Dual-Axis Accelerometer For HS3/4/4-DIFF Handyscopes, +/- 2G
TP-ACC20-25
The Accelerometer is a low cost, low power, complete dual-axis accelerometer with signal conditioned voltage outputs. The output signals are analog voltage proportional to acceleration. The Accelerometer is capable of measuring both positive and negative accelerations to at least +/- 2G.
-
product
Triaxal Seismograph
BC 1313 TRIAXIAL SEISMOGRAPH
BC 1313 seismographs are seismic accelerometers, the parameter measured – vibration acceleration. For BC 1313 seismic transducers, the system is provided for sensing element electrical stimulation using an actuator to determine conversion ratio true value during periodic recalibration without dismantling. Power check system is also allowed for in BC 1313 seismographs.
-
product
High Sensitivity Accelerometers
Metra Mess- und Frequenztechnik in Radebeul e.K.
The piezoelectric accelerometers on this page are intended for the measurement of lowest vibrations. Typical fields of application include the monitoring of buildings, dams, bridges, oil platforms and pipelines. These sensors are often called seismic accelerometers because they are used to monitor construction activity, volcanoes and earthquakes. Their high sensitivity is achieved -unlike other high sensitivity accelerometers- by the sensing element itself and not by internal amplification. From this results highest resolution and lowest noise.
-
product
Force Balanced Accelerometer
PA-23, PA-23BH, S-230
The Geotech Model S-230 is a high resolution, 1-component, force balanced accelerometer capable of meeting the noise and stability requirements of the most demanding seismic studies. It features a very wide frequency response (DC to 90 Hz) and an internal calibration coil.
-
product
Linear Accelerometers
Columbia Research Laboratories
Columbia Research Labs line of Force Balance Linear Accelerometers offers low cost, high performance, general purpose single axis accelerometers that are ideal for DC and low frequency measurements, with both voltage and current signal outputs available. Also offered are Columbia's Solid State Sensors and our specialized Airborne Sensors that generate outputs specifically designed to operate from +24 to +32VDC aircraft power, that is excellent for airborne telemetry applications. And our Low Noise Sensors are designed for use in seismic, low level, low frequency motion studies.
-
product
Accelerometers
ROGA-Instruments provides a broad range of accelerometers for General applications, Seismic measurements, High acceleration and shock, Light test objects, Triaxial measurements and Industrial applications.
-
product
Piezoelectric
Columbia Research Laboratories
The Columbia product line of piezoelectric accelerometers is widely known for reliable performance, quality and ruggedness and is always expanding to meet the unique challenging and ever changing requirements of our customers. The selection of specifications, sizes and configurations is large and diverse and suitable for use on many applications requiring features such as, high performance, high accuracy, high temperature, seismic event, 4-20mA output, airborne, miniature size and general purpose use.
-
product
Digital Magnetic Compass
SeaTRAX
The SeaTRAX with PNI’s high sensitivity magnetometers and accelerometers is a COTS high- performance heading sensor for seismic streamers and towed arrays.
-
product
Seismic Transducers Calibration System
Calibration of the seismic sensors should be conducted in the low-frequency domain, which means, that the relative method used for calibration of the vibration transducers is not applicable since it does not guarantee the required accuracy level. The problem is that the reference accelerometers have uneven AFR characteristic in the low-frequency domain. Thus, calibration of seismic transducers requires implementation of a different approach.
-
product
Miniature
Columbia Research Laboratories
This group is made up of the 6000 and 7000 Series Accelerometers. The 6000 Series offers detachable cables and connector assemblies, a special inverted seismic element for mechanical isolation and other features normally available only on standard size sensors. The 7000 Series are true "shear-mode" design accelerometers which offer performance characteristics and accuracies normally only available with standard size accelerometers. High temperature models of these series are available and will operate to +500°F. For best performance use with Columbia Model 4601 Charge Amplifier or Model 5810 Inline Charge Converter.
-
product
Accelerometers
Columbia Research Laboratories
The force balance accelerometer has a classical critically-damped, second-order frequency response. There is no peaking in the response but simply a smooth roll-off above the natural frequency. This property along with the excellent characteristics of the "HP" torquer design makes Columbia accelerometers the best choice for demanding applications where precise DC and near-DC measurements are needed in demanding shock and wide band vibration environments. Columbia force balance accelerometers are available to cover virtually all applications. Low noise, high output units can be used for seismic structure motion studies while miniature, high range versions are optimum for measuring more violent high G environments encountered in many industrial, aircraft and missile applications.
-
product
Accelerometers
An accelerometer is used in manufacturing machine maintenance to inspect equipment vibration. An accelerometer also is used in product testing to measure the vibration of various components.A triaxial accelerometer, also called a 3-axis accelerometer, provides measurements of the following parameters: vibration acceleration, vibration velocity and vibration displacement. In this way, vibration is measured and recorded with great precision.Most accelerometer products offered by PCE Instruments are portable devices. Many feature memory functionality so that readings can be stored and retrieved later for in-depth analysis. Some accelerometer models come with a manufacturer's calibration certificate. Some accelerometer models can be calibrated to ISO standards optionally for an additional fee.
-
product
Accelerometers
A device that measures the vibration, or acceleration of motion, of a structure.
-
product
Seismic Digitizers / Recorders
SMART Series
The SMART Series of instruments represent the logical solution for seismological data acquisition: a common design for a digitizer, portable recorder, and strong motion recorder(the all-in-one solution).
-
product
Seismic Vibration
Seismic vibration instrumentation is used to measure structural vibration on bearing housings, piping, machinery housings, and machine support structures. It is particularly suitable for machinery with rolling-element bearings. These types of bearings will generally transmit both shaft-and bearing-related vibration to the outside of the machine where it can be detected by seismic measurements.
-
product
Bandwidth-Controlled Seismic Source
eSource
Teledyne Bolt, Inc. has engineered a new type of airgun designed to reduce the potential impact of seismic acquisition operations on marine life while also delivering optimal bandwidth for subsurface imaging. eSource is designed to reduce the high-frequency components believed to have most potential for causing disturbance to marine life while retaining the low-frequency components critical to seismic exploration.
-
product
Digital Accelerometer
ZET 7052-N
Digital accelerometer ZET 7052-N is equipped with a compact sensing element and is designed for linear acceleration and vibration acceleration variable constituent measurement via three mutually perpendicular planes. Small weight of sensing element (1,5 g) considerably reduces self-mass load and compact dimensions (8,5×8,5×8,5 mm) enable use of the digital accelerometer ZET 7052-N for vibration measurements in systems with small active area.
-
product
Advanced Seismic Source
GI-SOURCE
Sercel developed the GI-SOURCE to reduce and suppress the bubble oscillation from a single impulsive source to simplify processing. The GI-SOURCE impulsive source is based on the same technology as the GI-SOURCE but is different in that it has two independent air chambers within the same casing : the Generator (generating the primary pulse and creating the main bubble) and the Injector (injecting air inside the main bubble so that it collapses quickly).
-
product
Industrial Accelerometers
Metra Mess- und Frequenztechnik in Radebeul e.K.
These piezoelectric vibration transducers have been designed for application under rough environmental conditions. They are dust and water protected. Their mounting base is insulated to avoid ground loops which may cause errors, particularly, close to big machinery.
-
product
Miniature Accelerometers
Metra Mess- und Frequenztechnik in Radebeul e.K.
These piezoelectric accelerometers are particularly suited for small and light test objects. Of particular advantage may also be their high resonant frequencies. Due to the piezoelectric principle with its wide dynamic range both high acceleration and lowest vibration can be measured with the same sensor.
-
product
Three Axis Accelerometers
TAA
The Inertial Labs MEMS TAA-308, TAA-315 and TAA-340 are the third generation of the Inertial Labs MEMS, three-axis high-precision accelerometers released in a stand-alone design. The TAA-308, TAA-315 and TAA-340 are revolutionary, compact, self-contained, strapdown, Navigation-grade Accelerometers that measure linear accelerations with high precision due to their unique design and developed by Inertial Labs over last 20 years several significant know-know and technics in calibrations of inertial sensors. Measured by TAA Accelerometers accelerations are determined with low noise and very good repeatability for both motionless and dynamic applications.
-
product
Kit for Seismic Research Performance
The kit for seismic research performance is used for performing measurements in various climatic zones. Splash-proof connections GSC-4H (Herma-4) are used for establishing a reliable connection between the geophones within the seismic system.
-
product
Triaxial Accelerometers
Metra Mess- und Frequenztechnik in Radebeul e.K.
Triaxial accelerometers are intended for simultaneous measurement of vibration in 3 perpendicular axis. All models have a central drilling for easy screw attachment and convenient axis alignment.
-
product
Accelerometers
Dytran accelerometers are used for product testing & development, structural monitoring, and industrial machinery health monitoring management. We offer a wide range of piezoelectric & VC MEMS sensors.
-
product
Angular Accelerometers
Columbia Research Laboratories
Columbia Research Labs offers Angular Accelerometers that use the fluid rotor concept of sensing angular acceleration resulting in a highly accurate precision Angular Accelerometer that provide excellent bias stability and rejection of linear acceleration. We also offer smaller electrically damped Angular Accelerometers that provide exceptional high frequency characteristics for an angular acceleration within its range of sensitivity. Lastly we offer a Variable Range Angular Accelerometer allowing the customer to change the measurement range of the sensor to meet their requirements.
-
product
Accelerometers
Honeywell Industrial Automation
Honeywell Sensotec Accelerometers are manufactured as standard, modified standard, and custom to provide the fastest possible delivery. Many units can be shipped from our extensive accelerometer stocking program within 24 hours. We offer a wide range of frequencies from DC to 6000 Hz and full ranges of 5 G to 2000 G. These units will survive overloads up to 500% (varies with model) and are also designed to cope with operating temperature between 100 and 500 degrees Fahrenheit.
-
product
Triaxial Linear Accelerometers
Columbia Research Laboratories
The Triaxial Force Balance Linear Accelerometers range from general purpose, low cost sensors, capable of measuring DC and low frequency acceleration simultaneously in three axes, to Miniature Airborne, Highly Reliable Sensors that operate from +24 to +32VDC Aircraft power. Also offered are compact, premium performance, extremely rugged sensors, well suited for demanding missile and airborne applications.
-
product
Seismic Refraction&Reflection System
WZG-24B
Based on WZG-24 engineering seismograph, WZG-24B 24 channels Engineering Seismograph is developed as a 24bit instrument under Chinese/English version WINDOWS operating system. With years of designing and manufacture experiences, and accepting latest electronic technologies and design ideas, WZG-24B features multi-function, high accuracy, high speed, reliable data and good expandability.
-
product
Accelerometer
EMIC offers many kinds of accelerometers available for various vibration measurements. They are a ultra small light weight accelerometer for highly precise measurement, a special tri-axial accelerometer for simultaneously measuring a vibration in three orthogonal axes, a large output accelerometer for measuring an earthquake and a suitable accelerometer for measuring and analyzing a building structure.
-
product
Accelerometers
356A02
Sensitivity (10 %)10 mV/g1.02 mV/(m/s) Measurement Range:500 g pk4900 m/s pk Frequency Range: (5 %)1 to 5000 Hz1 to 5000 Hz Frequency Range: (10 %)0.5 to 6000 Hz0.5 to 6000 Hz Resonant Frequency:25 kHz 25 kHz Broadband Resolution (1)0.0005 grms 0.005 m/s rms Non-Linearity: (400 g, 3920 m/s)1 % 1 % Non-Linearity (500 g, 4900 m/s)2 % 2 % Transverse Sensitivity:5 % 5 %.
-
product
ICP® Shock Accelerometers
Piezoelectric ICP® accelerometers afford a very high signal output (+/- 5 volts full scale) and the ease of two-wire electrical connectivity. Their inherent ruggedness enables them to be severely over ranged without damage. The addition of internal mechanical isolation minimizes the high frequency stress that would otherwise be encountered by their ceramic sensing elements. This mechanical isolation, coupled with an internal 2-pole electrical filter, built into the ICP® circuitry, tailors the overall accelerometer response to assure data quality to frequencies as high as 10 kHz. Depending on the specific model, accelerations in excess of 50 kg can be successfully measured. These modern designs, with their internal elastomeric isolation materials are verified through calibration to remain dynamically linear and are enabling piezoelectric accelerometers to operate in increasingly severe acceleration environments.
