Filter Results By:
Products
Applications
Manufacturers
- Advanced Telemetrics International
product
Band-On Telemetry System
Advanced Telemetrics International
The ATi Band-On Telemetry System transmits real-time sensor data from a rotating shaft while the system is running. The system consists of one or more rotating signal conditioner/ transmitter modules with battery pack and a stationary receiver. Rotating transmitters are available to interface with most any type of sensor including strain gages, thermocouples, thermistors, RTDs and accelerometers.
-
product
Tachometers
SHIMPO offers a wide range of hand-held tachometers that measure the total number of revolutions of a shaft or number of pulses of reciprocating equipment. Our models can measure and record last/min/max and up to 10 reading using up to 16 different units of measure. Our tachometers are designed for applications such as Motor Speed/Conveyor Speed/Fan Speed/Length Measurements that measure rpm of motors or shafts, either contact or non-contact with Laser style combination tachometer.
-
product
Datum Universal Interface
DUI
Datum Electronics specifically designed the Universal Torque Sensor Interface which accepts serial data, displaying the output data and a wide range of additional analogue and digital outputs, s 4-20mA, +/-5Vdc, 0-5Vdc, +/-10Vdc, 0-10Vdc as well as RS232/485 serial data.The Datum Universal Interface (DUI) interfaces with all our rotary, static, reaction, digital torque sensors and torque transducers, as well as shaft power measurement solutions.
-
product
Rectal Probe For Mice (Isolated)
RET-3 ISO
• An isolated sensor (can be used with monitoring equipment where electrical interference from other electrodes may be present).• Reinforced strain relief for applications where probe is in more frequent use.• Smooth ball tip. Stainless steel shaft - 3/4'' long, .028'' diameter. Tip diameter .065'', 5 foot lead length. Time constant 0.5 seconds.
-
product
Immersion Probe For Liquid
DPT-12
DPT-12 Immersion Probe for Liquids - 12'' #304 stainless steel welded shaft. Wooden Handle. Diameter is .3/16'' diameter. Immersible. Maximum temperature 350°C, Time constant 2 Seconds. 5 foot lead. Not isolated.
-
product
Loadpin Load Cell
LP
Designed to replace pins or bolts that carry a loadStainless steel constructionCapable of 100% humidity, 30G mechanical shock and 5G vibrationUsed with clevises, or pulley shafts to monitor loadsCapacity 1,740 lbf
-
product
Measurement
Tachometer
Tachometer is used for measuring the rotation frequency of shafts in machines and mechanisms, as well as for calculating the number of complete revolutions. Typically, for measuring the rotation frequency, optical or induction rpm sensors are used.
-
product
Magnet Wheels Pulse Generators
199SM / 198EM Magnet Wheels
Magnet wheels work with Electro-Sensors Hall Effect shaft speed sensors providing 120 alternating magnetic poles around the circumference of the 3.75" diameter. The 199SM models mount around shafts up to 3" in diameter and are secured with set screws (provided). The 198EM mounts on the end of a shaft with a 10-32 UNF screw (provided - requires center drilling and tapping the shaft).• Use with 906, 906B, 1101 and other Hall Effect, non-metallic-end-capped shaft speed sensors (consult factory)
-
product
Rectal Probe For Rats
RET-2
• Smooth ball tip. Stainless steel shaft - 1'' long, .059'' diameter. Tip diameter .125'', 5 foot lead length. Time constant 0.8 seconds. Not Isolated
-
product
Pro Laser Tachometer
332
The #332 is the ideal tool for easy and accurate measurement of RPM in almost any environment. Simply aim the laser beam at a reflective mark placed on a rotating device, push the button and the RPM reading is immediately displayed. No contact with the shaft or wheel is necessary. The laser beam is not affected by shop light and can detect RPM from longer distances of up to 6 feet away. The #332 can measure up to 99,999 RPM in 1 RPM increments. It can be used to measure RPM on coil-on-plug and diesel engines, where conventional inductive tachometers can not be used. Other uses include generators, compressors, industrial engines, fans, gears and more. Zippered case, reflective tape, instructions & 9V battery included.
-
product
Electrostatic Capacitance-Type Gap Detectors
VE series
VE series are non-contact type of vibration/small displacement detector with high accuracy which can measure the distance between conductor such as metal and sensor’s surface in micron/submicron resolution. It demonstrates its best performance when used for the measurement and control of the axial and surface vibration of rotational shafts such as main shaft of turbines, electric motors, compressors, and of the thickness and width of moving objects. In addition to the measurement of the amount of displacement, a gap detector can also be used for a wide range of other measurement and control applications such as the measurement of the amount of slack or warping. The non-contact measurement process enables to apply no load to rotational or vibration body, and does not affect the material under measurement.
-
product
CamTrac Z-Axis Test Fixture Kits
CT Serie
The CT Series Mechanical Kits, utilizing the patented CAM mechanism1, offset the same precision linear motion. The 'Z' axis motion is ideal for a larger point count mechanical test applications.The CT Series features a hinged 3/8" FR4 probe board, tooling holes for precision alignment, removable sides, precision shafts and cam slide block assemblies, and a pan latch assembly.
-
product
Shaft Alignment
NXA Pro
30 years of innovation continue with the introduction of the NXA Pro.
-
product
Mechanical Counter
SP101/102 Series
The SP-101/102 Series is a heavy duty totalizer. It has a double sided shaft for stability. Available in Revolution or Rotary type movements. Input shaft direction is choice between top going or top coming. Count speed range from 300 ~ 3000 rpm. It is a available in 4 or 5 digits with a large digit size of 6.0 x 4.0mm. Resetting of count value is done easily with the front push button reset.
-
product
Instrumentation Tutor
Unitech Scales And Measurements Pvt. Ltd
This comprises of temperature and speed using different methods. RTD, thermistor and thermocouple are used as sensors with digital temperature indicator to measure temperature. A small water kettle is supplied as a temperature source upto 100°C. Glass bead thermometer is used as standard temperature measurement source to conduct the experiment. Magnetic and photo reflective sensors are used to measure speed. A FHP motor with speed regulator is used as speed source. To the shaft 60 teeth tone wheels are fixed to generate pulses.
-
product
Radio Telemetry
Procter & Chester Measurements Ltd
Radio Telemetry: A transmission of data from a remote source via a radio to a receiving station for recording and analysis. Inductance: A contactless method of supplying power to (in this case) a strain gauge bridge. The signal is then transmitted back to the electronics. Slip Ring: Consists of a conductive band mounted on a shaft and is insulated from it. The wheatstone bridge is connected to the bands (usually four off). Fixed brushes or contacts make contact on to the bands to transfer power to the bridge and signal back to the static instrumentation.
-
product
Linear Hall Sensor
The output of a hall effect sensor is a voltage which changes in proportion to the shaft extension. A constant voltage is required across the supply and ground wires of the sensor. The sensor consists of a Hall Effect element, and a shaft which houses a magnet. When the position of the sensor changes relative to the shaft, the change in magnetic field in the sensor results in a change in output voltage.
-
product
LM Guide Miniature Actuator.
KR15
Ultra miniature actuator with a 15 mm high nut block and a 30 mm wide rail. The integration of the LM guide and ball screw can make a compact, high precision, and high rigidity actuator. The integration of the LM guide and ball screw can make a compact, high precision, and high rigidity actuator. Rustproof stainless steel is adopted in the outer rail, nut block, and ball screw shaft.
-
product
Laser Tachometer
LaserTach™
The LaserTach™ ICP™ tachometer senses the speed of rotating equipment and outputs an analog voltage signal for referencing vibration signals to shaft speed. The sensor allows for measurements in excess of 30,000 RPM from distances as far as 20 inches (51 cm).
-
product
Rotating Ring Disk Electrode
RRDE-3A
RRDE-3A is a constant rotation system for use in hydrodynamic modulation rotating ring disk electrochemistry. A 7 mm diameter electrode with short stainless steel shaft provides for a miniature and concentric circle electrode system that is capable for highly accurate rotation and modulation even at radial modulation rates or wave forms.
-
product
Electrode Holder
HD22.2 - HD22.3
HD22.2: Laboratory electrode holder composed of base plate with built-in magnetic stirrer, shaft and replaceable electrode hold-er. Suitable diameter 12 mm. It holds up to 5 electrodes at the same time. Powered by power supplier SWD10 (optional). HD22.3: Laboratory electrode holder composed of base plate. Flexible arm for free positioning. Suitable for electrodes with diameter 12 mm. It holds up to 5 electrodes at the same time.
-
product
In-Line Full Automatic Testing System
ALMAX
Automated press unit with board loading belt.ALMAX can become automated in-line type in-circuit tester in case our ICT is integrated. And it also can become automated in-line function tester as well.PLC is not used in order to reduce cost as a PC control mechanical part.Press unit is 4 shaft structures which reduce unbalanced load and contact fail of probe pins.
-
product
1, 2, or 3 Channels @ 0.5 VA, 1.5 VA or 3.0 VA
DSx
Synchros are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Digital-to-Synchro simulator is used to convert digital angle/velocity commands to corresponding Synchro/Resolver AC signals.
-
product
Pulse Generators
Split Collar Pulser Wraps
Pulser wraps clamp around a rotating shaft and work with Electro-Sensors shaft speed sensors and are an ideal solution for installations where the end of the shaft is inaccessible. The two halves fasten together around the monitored shaft with recessed Allen head socket screws (provided). Standard and custom models accommodate any shaft diameter, tight spaces, and keyways. • Standard wraps operate to 3,000 rpm (high-speed also available) • Standard wraps available in PVC, aluminum, or stainless steel
-
product
Load Measuring Pins
Magtrol Load Measuring Pins are temperature-compensated transducers used to measure load and force and provide overload protection. The pins are mounted into machines in place of normal shafts and fitted with strain gauges, allowing them to produce a signal proportional to the measured load.
-
product
Rotating Telemetry Systems
2100B Series
Advanced Telemetrics International
Are ideal for transmitting coupled data signals from sensors, which are mounted on rotating shafts or machinery to a stationary receiver.
-
product
Shaft Alignment
AT-200
Connectivity, mobile devices, cloud-based platform, apps are integrated in the AT-200 making it a tool for short response time between machine failures and corrective actions. The smart sensors use CCD technology for a superior measurement performance and precision alignment.
-
product
Tachometers
Is an instrument measuring the rotation speed of a shaft or disk, as in a motor or other machine.
-
product
Signal Analysis
Synchronous Accumulation (Order Analysis)
Order analysis is one of the most convenient and efficient methods for diagnostics and balancing of rotating mechanisms and transmission gears. With an RPM sensor and a vibration sensor, it is possible to study the time characteristics of gear vibration signals. It is a well-known fact that a signal from a vibration sensor is affected by signals from other sources. To tune out from the disturbing signals, the synchronous signal accumulation method is used. For each shaft rotation, the RPM sensor provides a rotation mark. This signal serves as a triggering strobe for the vibration sensor signal sweeping. The obtained signal sweeps are combined. All the sources of the signals related to the shaft frequency (frequency of rotation) are accumulated and increased in the accumulator linearly proportionally to the N number of rotations. All other signals that are not correlated with the shaft frequency are accumulated proportionally to N1/2 and in case of a greater number of averagings, the useful signal exceeds the interference level.
-
product
Level Float Switch
2285
The 2285 Level Float Switch is suitable for level switching of various liquids, sewage in shafts, tanks, basins or cisterns. The double-chambered float is made of injection molded tough polypropylene that ensures good waterproof protection.
