Filter Results By:
Products
Applications
Manufacturers
- LBA Group, Inc
product
Wideband Swept Antenna, Cable Analyzer
SWR TRUE 3013
• A cost-effective SWR Analyzer covering all Cellular and radio communication bands 30-2700 MHz• Measures transmition & antenna impedance, frequency, SWR, return loss, and bandwidth by sweeping band of interest• Built-in synthesized RF sweep generator• SWR TRUE 3013 Antenna Analyzer gives you quick and reliable antenna and cable trouble-shooting capabilities• 5 in 1 analyzes for antenna tuning and control• Measured results can be stored for further analyzing and documentation on internal and external storage media• Time stamp and operator ID capability included• LCD Display works in direct sunlight and with backlight in dark areas
-
product
ASA200
The ASA200 Analog Signature Analyser will assist you in testing, diagnosing and troubleshooting printed circuit boards without powering them (known as ‘power-off testing’).Connected via USB to a compatible PC running our own free software the ASA200 you can easily capture, measure and compare known good signatures (from your ‘golden’ board) with signatures from your suspect board. The built-in gate/bias generator (+/-10V, 100ohm source impedance) can be used to help test active components such as SCR’s, opto-couplers, small relays, TRIAC’s etc. An external dual footswitch can be connected to the ASA200 and can be user configured to control various functions.With the ASA200 we set out to bring the incredibly powerful technique of Analog Signature Analysis to engineers and repair shops at an affordable price.
-
product
USB to I2C Adapter
Model JI-300
The JI-300 is a versatile, easy to use PC hosted adapter used to drive I2C communicationsto/from a target device. The desktop unit can be configured to interface a variety of I2Cnetworks. Bus parameters such as clock frequency, duty-cycle, setup and hold times, busvoltage, and pull-up resistor values can be varied. JI-300''s diagnostic features including"excessive clock-stretch", "bus-not-free", and "bus contention" monitoring, as well as statusreporting at the conclusion of each message transaction simplifies I2C trouble-shooting. AWindows software application manages the setup and control of the instrument.Communications and unit power is provided via a USB 2.0 connection.
-
product
Continuity Testers
Triplett Test Equipment & Tools
Tester performs a TIA568 test on CAT5/6 network cable (RJ45) with instant PASS/FAIL results — opens/shorts, reversals, split pairs, and continuity. It is ruggedized and cushioned for toolbox use with a hidden drawer for remote storage. Includes a built-in tone generator for tracing and troubleshooting.
-
product
Network Analyzers
The LanExpert LE80 Inline network analyzer is a single solution for analyzing and troubleshooting networks from the cabling to the packet. The LE80 tests Wiremap, Length, PoE, Tone and Port ID.
-
product
Network Analyzer, Tester, LED
72-9450
This cable tester allows for quick and easy troubleshooting of RJ45 and USB cables. Checks for continuity, faulty wiring, open, shorts, straight through or cross pinning of cables.
-
product
Transformer Rated Metering Site Training Bench
Model 8833
The PowerMaster® 8813 is a true 3-phase training simulator for metering technicians to help improve their troubleshooting skills for applications encountered in the field. The Model 8813 provides a safe, controlled environment to help the trainee accelerate their education in meter testing and wiring verification. The training simulator also features the ability to simulate over 28 commonly found metering errors in the field. Paired with the Training Administrator Station (TAS), the bench can be controlled remotely over a closed WIFI network, and each trainee’s performance is recorded and time stamped for every session.
-
product
Advanced OTDR
MTP-200
MTP-200 series are the compact multi-functional platform, which are specially designed for FTTx/WAN applications and can meet the test requirements of installers, contractors and service operators during network installation, PC Software Download construction, maintenance and troubleshooting. It is convenient and accurate for auto/manual testing, multi-wavelength testing and multi-functional analysis.
-
product
Benchtop Water Quality Meters
LAQUA F-72
Water quality analysis is repeatedly performed in laboratories on a daily basis. Our high-end benchtop model was developed to provide simplicity with excellent on-site usability - from operation and maintenance through to troubleshooting.
-
product
HVAC/R Environmental Meter
FLIR EM54
The FLIR EM54 is ideal for inspecting and troubleshooting HVAC/R ducting systems within residential, commercial, and industrial facilities. This meter can help you verify that duct inlets and outlets have the specified volumetric flow – a prerequisite to an efficient functional system. Featuring humidity, wet bulb, and dew point functions, the EM54 can measure deviations from proper relative humidity levels. Plus, the included Type-K contact temperature probe is useful to check electric motors and thermal equipment components for proper operating temperatures.
-
product
API Testing with LoadView
Simulate 1,000s of users hitting your API every second to generate 100,000+ calls to your server per load testing session.Define your API tests to simulate traffic at the pace you need by implementing a load curve that increases the number of simultaneous users as necessary to properly test your system.Gather performance metrics consisting of the response times of each session and validation that the API returns the expected results in each response.Visualize how the average response time is affected as you increase the number of simultaneous users.Examine individual test sessions to see error codes and utilize additional troubleshooting tools such as traceroutes, waterfall charts and a copy of the server response.
-
product
Copper & Fiber Network Troubleshooter
NAVITEK NT
The new NaviTEK NT is a network tester for troubleshooting and maintenance of active and passive copper and fibre networks. Incorporating an improved graphical interface NaviTEK NT allows network technicians to pinpoint and solve network connectivity issues faster than ever before. Subsequently, tests can be saved as pdf reports and shared with colleagues and clients using the free IDEAL AnyWare™ app.
-
product
Decade Box, Calibrated W/Data, Resistance, 7, 1ohm to 11.11111Mohm, 1 %
72-7270 CAL D
The 72-7270 CAL D from Tenma is a resistance decade box. It is ideal for service, prototype and experimental use. This useful tool may be set resistance value from 1 to 11,111,110 ohm in one ohm increments. The decade accuracy is ±1% resistors used throughout. It has weight of 320g/0.70lb and dimension 14.7cm × 11.7cm × 5.5cm (5.79" × 4.61" × 2.16"). It is typically used in general applications, troubleshooting, maintenance, education and vocational training, production line testing, radio and TV services, working standards, research design & develop, physics laboratory work.
-
product
Modbus Master Data Scanner
ModScan
ModScan is a Windows application which operates as a modbus master. It allows you to access and change data points in a connected slave device using either the RTU or ASCII Transmission mode. ModScan is ideally suited for quick and easy compliance testing of the modbus protocol and its built-in display of serial traffic allows effective troubleshooting of field connections.
-
product
Avionics Test & Simulation Software
Ballard CoPilot® is an intuitive, graphical software program that allows you to easily monitor, record, replay, analyze, and simulate avionics bus data. With CoPilot you can interact directly with data on multiple buses using Ballard avionics interface hardware or work with previously recorded data. This advanced program features powerful tools for development, testing, troubleshooting and maintenance of avionics equipment and systems.
-
product
Time Domain Reflectometers and S-Parameter Analyzers
The Teledyne LeCroy WavePulser 40iX and the Teledyne Test Tools T3SP15D are a perfect combination of complimentary products to serve the requirements on testing, validating and troubleshooting cables, backplanes, connectors, transmission lines on boards and interconnect.
-
product
6-24V Heavy Duty Circuit Tester
1672
Peaceful Thriving Enterprise Co Ltd
Check on 6, 12 and 24V systems.1. Locate short, ground and open circuit.2. Make it easy to find out where current is present.3. The most essential for troubleshooting automotive electrical systems.4. Checks series-parallel switch and solenoid on tractor-trailer start systems.
-
product
EMC Probes
The Beehive Electronics 100 series EMC probes allow the accurate measurement of magnetic and electric fields. They are useful for EMC troubleshooting, field strength measurement, and troubleshooting of RF circuits.
-
product
Logic analyzers, MSOs
This digital logic analyzer has basic functions, easy operation and a new way of measuring data for monitoring and measuring signals in digital information processes. Thus, the device allows the analysis and troubleshooting in digital systems, such as transmission delays to be analyzed and the result of the information processing of the digital circuit and bus technology.
-
product
Digital Video Inspection Microscope
Contamination is the first reason for troubleshooting optical networks. Proactive inspection and cleaning of fibre connectors can prevent poor signal performance, damage to equipment, and network downtime. DIAMOND’s Video Microscope Kit contains all necessary tools for proper inspection and cleaning of the connector’s front-faces to help ensure optimal connector performance.
-
product
Combo Measuring Receiver/ TV Analyzer
VAROS 106
High accuracy, an easy handling as well as the modularand rugged construction will support the technician onsite in his tasks: perfect troubleshooting in all distribution networks with FM, return channel, DAB/DAB +, DVB-T2, cable TV, WiFi or SAT – the VAROS 106 covers all ranages reliably. By any means a real allrounder.
-
product
JTAG/Background Debug Mode Test System PXI Card
NX5300
The NX5300 is a single slot 3U PXI device and interfaces to the unit under test via an On-Chip Debug (OCD) or JTAG port. The NX5300 is a high performance JTAG based background debug mode (BDM) diagnostic system designed for functional test, development, programming and troubleshooting of microprocessor and microcontroller based embedded processor systems.
-
product
Portable Analyzer and Calibrator
ECD’s portable analyzer and calibrator product lines are a simple convenient way to obtain fast, accurate pH and ORP measurements. They provide a milliVolt output signal for fast field analysis of samples, calibration verification, or trouble-shooting of installed sensors.
-
product
ProfiShark Network TAPs
ProfiSharks are portable traffic capture devices that provide quick packet-level insight anywhere they are deployed. With capture regardless of packet rate and high quality hardware timestamping, ProfiShark delivers high fidelity capture files, forming an ideal starting point for troubleshooting or network forensics. Designed for easy, non-intrusive traffic capture, ProfiShark offers a valuable improvement over less performant options, such as SPAN ports on a switch or direct capture on a laptop. They give reliable insight into the network, ensuring the quality of analysis, and optimizing workflow, without dropping any packets.
-
product
ARINC 818 Analyser
iWave’s ARINC 818 Video Protocol Analyzer (VPA) instantly verifies the ADVB Packets against ARINC818 Standards. ARINC818 VPA software efficiently captures, decodes the ADVB data, and displays the ADVB data, raw video data, and error status. It is an excellent troubleshooting tool that helps to quickly detect and rectify errors in the ARINC 818-2 applications, simultaneously ensuring compliance of the system with the ARINC 818-2 standards.
-
product
Serial Distance Display
TA903-03
This panel mounted or portable display will read Bendix/King serial distance as generated by their DME systems or GPS products. This long standing three wire format of CLK, DATA and REQ can now easily be displayed without the expense of a KTS143 test fixture. This product is ideal for shop and aircraft troubleshooting. The extruded aluminum enclosure is a standard DIN size(1/8) and the unit interfaces through a 25 pin D connector.
-
product
Network Analysis Solution
IOTA
IOTA is a complete network analysis and troubleshooting solution for a variety of use cases in small, mid-size enterprises, remote sites, and small data centers. It is a versatile integrated solution, combining TAP, storage, and analysis capabilities in a single portable device.
-
product
E84 Handheld Tester
E84
The E84 Handheld Tester is the most efficient tool available for quickly testing, trouble-shooting, and resolving E84 problems. This self-contained, battery operated tool integrates the industry-leading automated load and unload routines provided in the E84 Emulator.
-
product
Fiber Optic Test Kit
FTK-130
The SYOPTEK FTK series Single Mode/Multimode Fiber Optic Test Kit is the perfect all-in-one fiber optic test equipment kit. The FTK kit provides a wide selection of fiber optic testing, cleaning, and inspection equipment to enable technicians to install, troubleshoot and maintain fiber optic networks. It is really a cost-effective and easy-to-use solution for testing single mode and multimode fiber optic networks, troubleshooting of fiber networks.
-
product
NTDS I/O Analyzer
The NTDS I/O Analyzer provides insight and visibility, enabling users to quickly and efficiently analyze timing relationships, message protocols, throughput, and data integrity on all types of NTDS interfaces. It is capable of monitoring any combination of NTDS Parallel Type A, B, C, H and NTDS Serial Type D, E channels as defined in the MIL-STD-1397 revision B and C specifications regardless of NTDS mode. The channels are connected to existing NTDS cabling with NTDS tap boxes and extract ongoing communication. Each word of NTDS information received is time-stamped with a 125 nanosecond resolution clock ensuring highly accurate timing measurements. Data collected is stored locally for analysis and can be transmitted to external equipment enabling remote troubleshooting, event reconstruction, or time-critical feedback on system performance.
-
product
Insulation Multimeter
1577
The Fluke 1587 and 1577 Insulation Multimeters combine a digital insulation tester with a full-featured, true RMS digital multimeter in a single, compact, handheld unit, which provides maximum versatility for both troubleshooting and preventative maintenance.
