Filter Results By:
Products
Applications
Manufacturers
-
product
Ultrasonic Thickness Gauges
A widely used nondestructive test technique for measuring the thickness of a material from one side. It is fast, reliable, and versatile, and unlike a micrometer or caliper it requires access to only one side of the test piece.
-
product
Ultrasonic Thickness Gauge
UTG-1500
The new PHASE II UTG-1500 is a hand held microprocessor controlled ultrasonic thickness gauge specifically designed for measuring the thickness of metallic and non-metallic materials such as aluminum, titanium, plastics, ceramics, glass and any other good ultrasonic wave-conductor as long as it has parallel top and bottom surfaces.
-
product
Clamp-On ATEX Ultrasonic Flowmeter
KATflow 170
The flowmeter is intended for permanent operation in Zone 1 and 2 hazardous areas and is an economical choice for a variety of metering applications. The KATflow 170 demonstrates that even the most complex technical requirements can be met with straightforward solutions.
-
product
Wafer Inspection System
AutoWafer Pro™
AutoWafer pro is our most advanced ultrasonic equipment for detecting defects in bonded wafers in a production environment, providing fast, high-resolution scanning of 200mm and 300mm bonded wafers.
-
product
Ultrasonic Level Measurement
Ultrasonic technology is a perfect choice for level applications that require low cost, non-contact measurement of liquids and slurries for level, distance, volume and open channel flow. These products have excellent accuracy and will handle measurements up to 30’.
-
product
Standard Clamp-On Ultrasonic Transmitter
KATflow 100
The KATflow 100 is a compact clamp-on ultrasonic flow transmitter with a robust and practical design for permanent installation and flow measurement on single pipes.
-
product
Ultrasonic Thickness Gauge
72DL PLUS
The Olympus 72DL PLUS™ ultrasonic thickness gauge delivers precision thickness measurements at high speed in a portable, easy-to-use device. With fast scanning, advanced algorithms, and our lowest-ever minimum thickness capability, you can confidently measure the thickness of very thin layers in the most challenging applications.
-
product
Ultrasonic Portable Hardness Tester
UCI-3000
Advanced Ultrasonic Hardness Tester UCI 3000 applies ultrasonic contact impedance method to do comparative hardness measurement for testing pieces, with the high accuracy, efficiency, portability and easy operation. UCI 3000 is a high-precision portable device for quick measuring hardness of small fogging, cast material, weld inspection, heat affected zone, Ion-nitride stamping dies and molds, forms, presses, thin walled parts, bearings, tooth flanks, etc. It is used for measuring the hardness within the ranges of main hardness scales – HB, HRC as well as HV.
-
product
Ultrapulse
The James Ultrapulse is ideally suited for the testing of ceramic materials, refractories, plastics and laminates. Ultrasonic velocity measurement permits accurate and repeatable calculation of modulus of electricity, bulk density and the detection of cracks. Stored data can be uploaded to a PC with the optional hand-held terminal. The Ultrapulse can be used with a wide range of ultrasonic stansducers for all of your ceramic testing needs.
-
product
Ultrasonic Energy Meter
E8
Gentos Measurement & Control Co.
E8 series ultrasonic energy meter that can realize the bidirectional independent measurement function of "cold" and "hot". It adopts advanced modular all-in-one design, independent menu operation, LCD backlight display, and it is suitable for the continuous measurement of cooling and heating energy of central air-conditioning's chilled water and cooling water, meeting different measurement requirements.
-
product
Ultrasonic Portable Hardness Tester
MET-U1A/MET-U1A50/MET-U1A100/MET-U1A110
The PHASE II ultrasonic portable hardness testers are capable of measuring the surface hardness of a broad variety of metals on flat, round, thin or large surfaces. Unlike the standard Dynamic hardness testers, these "state-of-the-art" portable hardness testers incorporate "Ultrasonic UCI" technology, which enables the hardness testing of very thin and small workpieces, which otherwise could not be tested accurately using a portable device.
-
product
PXI Pulser/Receiver Card
The Innerspec PXI Pulser/Receiver is a high-power ultrasonic instrument designed to be installed on a standard PXI or CompactPCI chassis. The instrument provides 8kW (1200Vpp toneburst) of power which is ideal for researchers and integrators interested in a compact, high-power ultrasonic instrument to drive EMAT and piezoelectric transducers (standard or air-coupled).
-
product
Ultrasonic thickness gauge
The frequency range of sound that can be heard by the human ear is about 20Hz to 20KHz, and sound waves with higher frequencies are called ultrasonic waves. In general ultrasonic flaw detection equipment, 5MHz is often used in the range of 1MHz to 20MHz as standard.
-
product
Ultrasonic Energy Meter
D116-PT1000
Gentos Measurement & Control Co.
D116-PT1000 is an upgraded version of D116, adding heat measurement function, so it can detect flow rate and calorie consumption of the fluid at the same time.
-
product
Ultrasonic Inline Flow Meter
SONOFLOW IL.52
The SONOFLOW IL.52 sensor is designed for precise, fast and bidirectional measurement of ultra-low flow rates. Due to its instantaneous measuring method with high repetition rates, the ultrasonic inline flow meter is suitable for quick dosing processes and for measuring pulsating flows.
-
product
Ultrasonic Distance Sensors
Leuze electronic GmbH + Co. KG
Ultrasonic distance sensors can reliably detect partially or fully transparent objects and perform precise distance measurements. In addition, measurements can be performed in dusty, hazy or humid environments. Versions are available either with plastic or metal housing.
-
product
4-CH 10/12-Bit 20 MS/s Simultaneous-Sampling Analog Input Cards
PCI-9812
ADLINK’s PCI-9812 and PCI-9810 are 4-CH, 10 or 12-bit, 20 MS/s simultaneous-sampling analog input cards. The high-speed analog input channels are single-ended, with hardware programmable input ranges of ±1 V, ±5 V and input impedances of 50 Ω, 1.25 k Ω and 15 M Ω. The onboard 32 k-sample A/D FIFO can buffer so data throughput is less than 100 Mbytes/s, the FIFO performs as the temporary A/D sample buffer, and as a rule of thumb, no data loss will occur. When four channels operate at 20 MS/s simultaneously, each sample generates two bytes, resulting in 160 Mbyes/s (4 channels * 20 M * 2 bytes) throughput, which exceeds the peak 132 Mbyte/s bandwidth of PCI bus. To avoid data loss, the 32 k-sample FIFO is the limitation of sample count. In addition to the onboard 40 MHz time base, users are able to supply the external time base in either sine wave or digital forms. The PCI-9810 and PCI-9812 also feature external digital trigger and programmable analog trigger, thus the conversion start point of multiple cards can be synchronized to external events. The trigger modes include software-trigger, pre-trigger, post-trigger, middle-trigger and delay trigger, further expands the capabilities of these high-speed devices. ADLINK"s PCI-9812 and PCI-9810 deliver cost-effective and reliable data acquisition capabilities and are ideal for vibration testing, image digitizing, ultrasonic measurement, biomedical research, ATE and other high-end industrial, scientific, and military applications.
-
product
Ultrasonic Nebulizer
U5000AT+
Using an ultrasonic nebulizer in conjunction with an optical ICP system is a simple, cost-effective way to increase sensitivity and lower detection limits.
-
product
Digital Ultrasonic Flaw Detector
Are modern age portable and processor-based flaw detectors. They are made up of parts including an ultrasonic transducer, hardware & software for capturing signals and analysing them, a data logging module, and a waveform display for viewing the images and graphs.
-
product
Lactoscan MCC Milk Analyser
The Lactoscan MCC Milk Analyser makes quick analysis of milk and liquid Dairy products in just 30 seconds. The MCC uses Ultrasonic analysis to determine a wide range of parameters with just a small milk or Dairy sample.
-
product
Low Noise High Precision High Voltage Amplifier
WMA-280
The WMA-280 is a high voltage, low noise precision amplifier. Its specifications have been designed to serve the needs of a wide variety of high-tech experiments. The WMA-280 can be used for MEMS actuation, EO-modulators, as high voltage driver for PZT (piezo) positioners, ultrasonics, and many other applications. Its output noise is only 300 microVolt rms.
-
product
Handheld Digital Tachometer
TurboTester
The TurboTester® is an innovative and cost-effective handheld digital tachometer for testing and quality control of dental handpieces and ultrasonic scalers. The TurboTester® is a non-contact instrument which measures rotational speed (rotations / revolutions per minute) of high and low-speed handpieces and the vibration frequency of ultrasonic scalers.
-
product
Ultrasonic Wall Thickness
UTG
The PosiTector UTG measures the wall thickness of materials such as steel, plastic and more using ultrasonic technology. Ideal for measuring the effects of corrosion or erosion on tanks, pipes or any structure where access is limited to one side. Multiple echo (UTG M) Thru-Paint models measure the metal thickness of a painted structure without having to remove the coating.
-
product
Ultrasonic Inspection System
PULD 40
The PULD-40 is a versatile and highly accurate ultrasonic inspection system designed to meet the needs of our customers.
-
product
Non-contact level measurement
We provide reliable continuous non-contact level measurement using ultrasound or hydrostatically by using pressure cells as well as reliable measurement of level detection. Our ultrasonic or hydrostatic level measurement systems reliably and accurately detect the levels of liquid media.
-
product
Horn Analyzer
TRZ
The TRZ Horn Analyzer determines the operation frequency of the item to be tested and its impedance and current with the touch of a button. It’s quick and easy. With this quick and easily retrieved information, the user can perform the quality control of transducers, tuning of sonotrodes and ultrasonic horns, preventive and corrective maintenance of acoustic sets and much more (please, see the TRZ Applications).
-
product
50KHZ MEASUREMENT MICROPHONE
M50
The M50 is a precision engineered 50kHz omnidirectional measurement microphone ideally suited for acoustical measurements including high-end loudspeaker design and quality control, scientific research, measurements of ultrasonic or subsonic transducers, or any application where an extremely accurate free-field measurement microphone is required.
-
product
Ultrasonic Thickness Gauge
Shenzhen Linshang Technology Co., Ltd.
Ultrasonic thickness gauges (ultrasonic thickness testers, ultrasonic wall thickness gauges, ultrasonic thickness meters, etc.) measure the wall thickness of materials such as steel, plastic, and more using ultrasonic technology which is ideal for measuring the effects of corrosion on metal, pipes or any structure where access is limited to one side.
-
product
Ultrasonic Metal Welding
Ultrasonic metal welding method is used to join dissimilar metals of aluminum wire and copper for aluminum harnesses, thin copper alloys for vapor chambers and hoop materials, and aluminum laminated foil for rechargeable batteries.
-
