Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI 2A Multiplexer, 2-Bank, 64-Channel 1-Pole
40-614-010
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
product
80 Channel Relay Multiplexer
DP-VXI-4017
DP-VXI-4017 is an 80 Channel Relay Multiplexer constructed using ‘2 Form A’ (DPST) relays. It is a ‘C’ size 1 slot register based VXI module. This 80 Channel Relay Multiplexer module is highly configurable. As an 80 channel multiplexer, one input can be multiplexed to any of the 80 outputs or vice versa. The 80 channel multiplexer is divided into 8 banks of 10 channels each. This combination allows the board to be used as one group of 80x1 or two groups of 40x1 or four groups of 20x1 or eight groups of 10x1 differential multiplexer. The banks are isolated from each other by tree switches. 8 tree switches are used, one tree switch for each bank. A common tree switch is used to group all the eight banks. For short circuit protection resistors are provided for all the common terminals.
-
product
1x4 Multiplexer Plug-In
1260-134
The Astronics1260-134 is a sixteen 1x4 multiplexer plug-in card for the Adapt-a-Switch® platform. It installs, easily and directly from the front panel, into the Adapt-a-Switch VXI Carrier, 1260-100.
-
product
PXI 2A Multiplexer, 4-Bank, 16-Channel, 2-Pole
40-614B-007
This 4-bank, 16-channel, 2-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 26.5GHz, 50Ω, SMA, Remote Mount
40-785C-532-E
The 40-785C-532-E (PXI) and 42-785C-532-E (PXIe) are dual SP6T 26.5GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
product
LXI Microwave Multiplexer, 50Ω 6-Channel 11-Bank 26.5GHz SMA
60-801-311
The 60-801-311 is a 6-channel, 11-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
PXI RF Multiplexer, 10x SP4T, 1.3 GHz 75 Ω, Multiway Connectors
40-755-210
The 40-755-210 is a 10xSP4T 75 Ω multiplexer and is part of a range of high density RF multiplexers available in 50 Ω and 75 Ω variants with up to 10xSP4T switches in a single PXI module. They are available with two connector options; SMB that provides a frequency range of 1.8 GHz (50 Ω) / 1.3 GHz (75 Ω), or multiway which limits the bandwidth to 1.3 GHz but offers a high density solution occupying one PXI slot. The connectors used are fully supported by the range of Pickering Interfaces connection solutions.
-
product
PXIe Microwave Multiplexer, Single SP8T, 26.5 GHz, 50 Ω, SMA, Remote Mount, Failsafe
42-788-041-E
The 40-788-041-E (PXI) and 42-788-041-E (PXIe) are single failsafe SP8T 26.5 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
-
product
PCI Very High Density Multiplexer, 49-Channel, 4-Pole
50-670C-022-49/4
The 50-670C-022-49/4 is a 49-channel, 4-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670C shares exactly the same architecture as the established 40-670 range of PXI modules.
-
product
PXI/PXIe RF Multiplexer, Dual 6-Channel, Terminated, 8GHz, 50Ω, SMA
42-881B-002
The 40/42-881B has low VSWR characteristic over the full operating frequency range and consistent insertion loss characteristics. The use of solid state switches ensure a long service life with no wear out mechanism, making the module ideal for ATE systems requiring frequent and fast operating RF switching with no contact bounce.
-
product
PXI Dual SP6T Multiplexer 18GHz 50, SMA, Terminated
40-785B-522-T
The 40-785B-522-T is a dual 6-channel 18GHz terminated microwave multiplexer. The 40-785B range of multiplexers are available as a single or dual 6-channel panel mounted multiplexer with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
product
PXI/PXIe High Voltage Multiplexer, Triple 7-Channel, 2-Pole
40-321-122-HI
The 40-321-122-HI (PXI) and 42-321-122-HI (PXIe) are triple 7-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
product
LXI Microwave Multiplexer, 50Ω 4-Channel 5-Bank 26.5GHz SMA
60-802-305
The 60-802-305 is a 4-channel, 5-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
PXI Dual SP6T Multiplexer 40GHz 50 SMA-2.9
40-784A-042
Pickering Interfaces’ range of 40-784A PXI Microwave Multiplexer Modules have a characteristic impedance of 50Ω and are capable of switching signals up to 40GHz. Available in single, dual or triple, SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors
-
product
PXI/PXIe Very High Density Multiplexer, 49-Channel, 4-Pole
42-675B-002-49/4
The 40-675B-002-49/4 (PXI) and the 42-675B-002-49/4 (PXIe) are 49-channel, 4-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems.
-
product
PXI/PXIe High Density 2A Multiplexer, 4-Bank, 32-Channel, 1-Pole
40-614D-006
The 40-614D-006 (PXI) and 42-614D-006 (PXIe) 4-bank, 32-channel, 1-pole multiplexers are part of the High Density 2A multiplexer module range available in 22 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
PXI 5A Power Multiplexer, 2-Bank, 24-Channel
40-651A-002
The 40-651A-002 is part of our range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats.
-
product
Multiplexed Measurement Unit
YAV90MMU
YAV90MMU module (Multiplexed Measurement Unit) is a powerful subsystem containing 16-channel multiplexer and a 600V data acquisition channel with capability to control external switching and it is expandable through CAN bus.
-
product
PXI 10A Power MUX 8-Bank 4-Channel
40-661-001
The 40-661 is a single pole PXI power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available. Signal connections are made via front panel mounted 20-way GMCT plugs.
-
product
PXI 10 x 4 to 1 RF Multiplexer 500MHz 50 Ohm Multiway Connectors
40-755-010
The 40-755-010 is a 50 Ohm high density RF multiplexer (4 to 1) array with 10 MUXs in a single PXI module. The 40-755 range is available with two connector options, an SMB connector that provides a frequency range of 1.8GHz and is available in single or dual PXI slots, or a Souriau multiway connector which limits the bandwidth to 1.3GHz but offers a high density solution occupying just one PXI slot. The RF switch design is identical in each case.
-
product
PXI/PXIe MEMS Optical MUX, Dual 2-Channel, Single-Mode, 9/125 Fiber
40-855A-122-HI
The 40/42-855A-122-HI is a PXI/PXIe dual 2-channel multiplexer with FC/PC, includes hardware interlock connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
PXI Very High Density MUX 24 Chan 8 Pole
40-675-002-24/8
The 40-675 series of very high density low cost multiplexer modules are available in a versatile range of switching configurations. The modules are supplied pre-configured in one of six multiplexer modes suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
product
PXI/PXIe MEMS Optical MUX, Single 2-Channel, Single-Mode, 9/125 Fiber
40-855A-112-HI
The 40/42-855A-112-HI is a PXI/PXIe 2-channel multiplexer with FC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
PXI Dual 4 to 1 RF Multiplexer 3GHz 50 Ohm MCX
40-872-102
The 40-872-102 is a 50 Ohm 4 to 1 RF MUX with 2 banks in a single PXI slot. It exhibits low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths of the 40-872 has been minimized by careful attention to the mechanical and electrical design.
-
product
PXI/PXIe RF Multiplexer, Quad 4-Channel, 3GHz, 75Ω, SMB
40-832A-004
The 40-832A-004 (PXI) and 42-832A-004 (PXIe) are 75 Ohm 4 to 1 RF multiplexers with 4 banks in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
product
PXI Triple SP6T Multiplexer 18GHz 50 SMA
40-784A-023
Pickering Interfaces’ range of 40-784A PXI Microwave Multiplexer Modules have a characteristic impedance of 50Ω and are capable of switching signals up to 40GHz. Available in single, dual or triple, SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors
-
product
LXI Microwave Multiplexer, SP6T, 2-Bank, 40GHz, 50Ω, SMA-2.92, Terminated
60-800-502
Our 60-800-502 is a 2 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 40GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
PXI 2 Amp MUX, Single 16-Channel 2-Pole
40-635-102
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
PXI/PXIe Wide Current Range Multiplexer Module, Dual 12-Channel, 1-Pole
40-514-107
The 40-514-107 (PXI) and 42-514-107 (PXIe) are low density multiplexers in dual 12-channel, 1-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
product
PXI 2 Amp Multiplexer, Single 8-Channel, 8-Pole
40-635A-004
The 40-635A-004 is a single 8-channel, 8-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
PXI Solid State Multiplexer Module, Dual 3-Channel, 10 A, Hardware Interlock
40-666B-011-HI
The 40-666B-011-HI is a dual 3-channel 10A MUX with hardware interlock and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
