Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI Solid State MUX, 10 bank, 16 channel
40-680-002
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
product
Ferrous Wear Meter
Parker Kittiwake
Parker Ferrous Wear Meter (FWM) detects abrasive ware metal iron particles in an oil samples taken from lubricated engine, liner and cylinder machinery.
-
product
13 GHz Programmable Attentuator
PA13
This device has low impedance mismatch, high bandwidth, wide dynamic range and is capable of rapid state change. The PA13 can be an attractive alternative to either the manually operated microwave attenuator switches, which are expensive and are switched very slowly, or the relay attenuators which are expensive and wear out quickly.
-
product
PXI/PXIe RF Multiplexer, Dual 6-Channel, Terminated, 8GHz, 50Ω, SMA
42-881B-002
The 40/42-881B has low VSWR characteristic over the full operating frequency range and consistent insertion loss characteristics. The use of solid state switches ensure a long service life with no wear out mechanism, making the module ideal for ATE systems requiring frequent and fast operating RF switching with no contact bounce.
-
product
Universal Wear Tester
TF213
TESTEX Testing Equipment Systems Ltd.
Universal Wear Tester, to determine the wear and abrasion resistance of fabric used in clothing, footwear and industrials. Universal wear tester Supplies with surface abrasion head (inflated diaphragm method) and Flex abrasion head as well as necessary weights and initial supply of abrasives. Accessories are available for conducting frosting, pilling and edge abrasion tests.
-
product
High Speed Test Bench
AT444
AC motor with mechanical multiplying gearbox test benches allow precise programming of all drive parameters required for accurate rotating devices test.The use of special high-speed bearings, mechanical components and parts wear resistant leads to a large life. The supply includes the electronic drive and control as well as the entire oil cooling unit.
-
product
Mechanical Tester
NANOVEA Mechanical Tester is the most versatile nanoindenter and scratch tester capable of precisely measuring the micro- to nanomechanical properties of wide ranges of materials from thin films, coatings, ceramics and composites to polymers and bio materials via Indentation, Scratch and Friction testing. All NANOVEA Mechanical Tester models come with true feedback load control from independent load and depth sensors that provide unmatched accuracy and the highest repeatability available on the market. This technology allows a user to perform Nanoindentation and Microindentation for Hardness and Elastic Modulus Testing, Stress vs Strain Analysis, Creep and Relaxation, Loss and Storage Modulus, Yield Strength and Fatigue, Fracture Toughness and Nano-scratch & Micro-scratch for Scratch Hardness Testing, Multi-pass Wear Test, Cohesive and Adhesive Failure Testing as well as Coefficient of Friction testing, all available on one system.
-
product
Wrist Strap & Footwear Tester
STME-COMBI
Statclean Technology (S) Pte Ltd
The Wrist Strap and the Footwear Tester checks for the operating conditions with the strap on the wrist or foot wear on the foot. It clearly indicates whether or not the resistance of the wrist strap/ footwear system including the wearer is at least 0.75 Meg ohms and not more than 10/ 100 Meg ohms respectively.
-
product
Non-destructive Eddy Current Testing of Long Products such as Tubes, Rods, Wire, and Profiles
DEFECTOMAT® Product Familiy
Foerster Instruments, Incorporated
The DEFECTOMAT systems by FOERSTER were specially developed for quality testing and process monitoring of long products. From hot testing to all bright steel processing steps, the surfaces of semi-finished products made from austenitic, (non) ferromagnetic metals can be tested for defects. The DEFECTOMAT systems operate in a contactless and non-destructive manner in accordance with the eddy current method and are used for detecting short defects, such as holes or localized defects and transverse defects. The systems detect defective materials fully automatically and reliably. Defects can be marked, classified, and automatically discarded. the test speed of up to 150 m/s facilitates 100% testing, even at high production speeds. The systems benefit from low operating costs and frugal energy consumption as well as low maintenance costs, few wear parts, and low use of materials.
-
product
Contactless Safety Technology
The use of contact-free locking facilities, in particular for monitoring movable safety guards, offers the following advantages: * Simple adjustment, * No broken actuator, *High degree of tolerance to vibrations, moved doors and hoods, * No wear Exceptionally easy cleaning.
-
product
RJ45 Port Saver
#21025C
Extend the life of your tester by using the RJ45 PortSaver as your sacrificial cable. Eliminates the wear and tear from constantly plugging in and out of the tester port and minimizes the risk of damaging the RJ45 jack if the connector contacts are not crimped completely. Compatible with all Platinum Tool testers with built-in […]
-
product
Tribometers/Abrasion Testers
AEP Technology offers several ASTM, ISO DIN compliant friction and wear tester models optimized for various applications. The modular design allows it to run on one platform (rotary, linear reciprocating, linear, block-to-ring, etc.), and to ensure high repeatability, during the testing process our downward force friction and wear testing machine controls several standard tests. High-end electronics, multi-core 64-bit processor that allows it to use multiple in-situ sensing technologies (recording friction, wear, displacement, force, volume, temperature, humidity, position, speed, etc., during testing) with high resolution Embedded powerful platform imaging head (sections of atomic force microscopes, etc.). Ease of use and robust unique design make AEP Technology a powerful tool in friction and wear testing machine development and production environments.
-
product
ICI Mace Snag Tester
TESTEX Testing Equipment Systems Ltd.
ICI Mace Snag Tester, to determine the tendency of fabrics to snag (pull yarn loops from fabric) in normal wear (mace snag). ICI Mace Snag Tester complies with ASTM D3939, etc. Please contact us for more information about snagging test.
-
product
PXI Quad 4 to 1 RF Miltiplexer 6GHz 50 Ohm SMA Terminated
40-882-004
A 50 Ohm 4 to 1 6GHz PXI RF multiplexer available as a single MUX in one PXI slot, a dual MUX in two PXI slots, or triple and quad MUXs in three slot PXI modules. This PXI multiplexer exhibits low VSWR characteristically over the full operating frequency range and consistent insertion loss characteristics. The use of solid state switches ensures a long service life with no wear out mechanism, making the 40-882 MUX ideal for ATE systems requiring frequent and fast operating RF switching.
-
product
PXI Solid State Very High Density Matrix
40-501-001
The 40-501 is a very high density matrix using solid state switching configured as a 64x4 1-pole matrix in a single slot 3U PXI module. It is ideal for applications requiring fast operation and a long service life with frequent switch operations at high voltages. Since the design is based on solid state relays the matrix has no wear out mechanism.
-
product
Core Loss Testers
S30 and S30S Series
Stacks built with punched laminations can have a lot of quality issues. Even though the lamination material is tested in sheet format before any process, that alone is not sufficient to guarantee good quality stators. Wear and tear of the punch, bad welding, bad insulating coating in annealing add to the magnetic losses in the stator. It is always advisable to test the stator core in it's final format before winding to ensure good quality throughout the production batch.
-
product
Assay System (Rest System for Longevity)
New polymers are constantly being developed and component manufacturing techniques appear, allowing the gradual replacement of metallic materials by plastics or composites, in various fields of application, in different industries. In particular, in the air conditioning, heating and water supply sector, plastic components are subject to the aging process due to the temperature to which they are subjected or due to the amount of oxygen in the fluids. The Test System for Longevity and Accelerated Aging Tests developed by Controlar allows to foresee, in accelerated test, the wear throughout the life of the plastic components of the hydraulic systems, in order to prevent eventual failures during the useful life cycle of the DUT.
-
product
Laboratory Ferrography
T2FM 500
The SpectroT2FM 500 Analytical Ferrography Laboratory is a complete analytical system for the separation and interpretation of wear and contaminant particles in used lubricant oils, hydraulic fluids, coolants and fuels. It consists of the T2FM Ferrogram maker, a bichromatic microscope, video camera and image capture software.
-
product
PXI Solid State MUX, 1 bank, 160 channel
40-680-006
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
product
6, 8 GHz, 4 Channel Programmable Attentuator
QPA8, PA8
This device has low impedance mismatch, high bandwidth, wide dynamic range and is capable of rapid state change. The QPA8 can be an attractive alternative to either the manually operated microwave attenuator switches, which are expensive and are switched very slowly, or the relay attenuators which are expensive and wear out quickly. Attenuation is controlled in standard steps of 0.0625 dB. The 10 bit programmable range results in the full 210=1024 steps yielding a dynamic range of 0 to 63.9375dB. Non-standard custom step sizes are available.
-
product
13 GHz, 4 Channel Programmable Attentuator
QPA13
This device has low impedance mismatch, high bandwidth, wide dynamic range and is capable of rapid state change. The QPA13 can be an attractive alternative to either the manually operated microwave attenuator switches, which are expensive and are switched very slowly, or the relay attenuators which are expensive and wear out quickly.
-
product
Magnetic Switches / Magnetic Sensors
BERNSTEIN offers electromechanical reed contact magnetic switches and electronic versions which operate according to the Hall and magnetoresistive principle.The electronic versions are characterised by their enhanced mechanical properties (extremely high resistance to vibration, shock or impact) and are not prone to wear in operation. Thanks to the use of only one single “active” component (reed contact), “traditional” electromechanical magnetic switches are extremely reliable in operation. The universal current capability and low procurement costs allow these switches to be used in a wide range of applications.
-
product
Automated Wear Debris Analyzer
LaserNet 200 Series
The LaserNet 200 Series allows reliability professionals to quickly and easily assess machinery health in just minutes. By testing only a few milliliters of fluid, users see a complete picture of machine wear and particulate contamination. This enables the user to determine filtration efficiency, the type of wear mode occurring, and the change in ferrous debris concentration, for maintenance action.
-
product
Non-terminated SPDT Indium Phosphide Active RF Switch
Part No. InP1012-40
Non-terminated SPDT Indium Phosphide Active RF Switch • 3mm x 3mm x 1mm package size • 100ns switching time• Monolithic solid-state switch with no mechanical wear• Flip-chip packaging provides shock & vibration resistance• ENEPIG surface finish for solder bonding• Low loss package with organic overmold• Test board with K-connectors can be providedDC-40GHz40Gbps
-
product
Non-terminated SPDT Indium Phosphide Active RF Switch
Part No. InP1012-20
Non-terminated SPDT Indium Phosphide Active RF Switch • 3mm x 3mm x 1mm package size • 100ns switching time• Monolithic solid-state switch with no mechanical wear• Flip-chip packaging provides shock & vibration resistance• ENEPIG surface finish for solder bonding• Low loss package with organic overmold• Test board with K-connectors can be providedDC-20GHz
-
product
Three Phase Power Monitoring
PRÜFTECHNIK Condition Monitoring GmbH
A three-phase power monitor detects changes in electrical variables. With power monitoring on your assets, you can help reduce wear and damage, while also identifying what’s causing it. The Fluke 3540 FC three-phase power monitor can be used remotely or through a stationary connection.
-
product
Wear Testing Machine
M-2000
Jinan Testing Equipment IE Corporation
Model M-2000 Wear Testing Machine is to be used test the anti-wear performance for metal and non-metal specimen under the sliding, rolling, and sliding-rolling condition. The Wear Testing Machine can also test various materials under dry-friction and wet-friction. The wear testing system can calculate friction work & friction coefficient by the data acquired. The Wear Testing Machine is widely used in universities, research & scientific institutes.
-
product
PXI Solid State MUX, 5 bank, 32 channel
40-680-003
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
product
Noise & Vibration Measurement Systems
BK8600
Rotation can produce noise and extraneous vibration for any number of reasons and could cause wear, discomfort, or other problems. The BK8600 series of testers are specially designed to test for these.
-
product
Industrial Vibration Sensor
IVS-500
The new IVS-500 Industrial Vibration Sensor is the key to fast acoustic quality inspection, structure-borne noise analysis and reliable pass-fail decisions. This Laser sensor measures reliably, in demanding industrial environments, without contact and therefore without wear and on virtually all surfaces. Costs and yields are therefore optimized by reducing false rejects in the production and assembly process. The simple setup and ruggedized sensor design of the IVS-500 enable a smooth integration into production test systems. Complemented with the software tool QuickCheck, Polytec offers a comprehensive solution for reliable pass/fail analysis.
-
product
Axis Play Tester
PMS 3.5 | VP 225012
Maschinenbau Haldenwang GmbH & Co. KG.
The axis play tester PMS 3.5 is used to reliably determine defects and wear on steering parts, wheel bearings, suspension and suspension by counter-rotating transverse and longitudinal movement of the test plates. The built-in hydraulic drive ensures a powerful and even movement of the test plates. An automatic mode and other different operating modes make the PMS 3.5 easy to use.
